Dell PowerEdge 1600SC Manual de usuario

Dell™PowerEdge™1600SCSystemsInstallationandTroubleshooting

Guide

Introduction

Indicators, Codes, and Messages

Finding Software Solutions

Running the System Diagnostics

Troubleshooting Your System

Installing System Options

Installing Drives

Getting Help

Jumpers, Switches, and Connectors

I/O Ports and Connectors

Abbreviations and Acronyms

Information in this document is subject to change without notice.

©2003DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge, Dell OpenManage,DellNet,Dell Precision,Dimension,Inspiron, OptiPlex,and Latitude are trademarks of Dell Inc.; Intel is a

registered trademark of Intel Corporation; MS-DOS is a registered trademark of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Initial release: 22 Sep 2003

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page



Jumpers, Switches, and Connectors

Dell™PowerEdge™1600SCSystemsInstallationandTroubleshootingGuide

Jumpers—A General Explanation

System Board Jumpers

System Board Connectors

Disabling a Forgotten Password



This section provides specific information about the system jumpers. It also provides some basic information on jumpers and switches and describes the

connectors on the various boards in the system.



Jumpers—A General Explanation



Jumpers provide a convenient and reversible way of reconfiguring the circuitry on a printed circuit board. When reconfiguring the system, you may need to

change jumper settings on circuit boards or drives.



Jumpers



Jumpers are small blocks on a circuit board with two or more pins emerging from them. Plastic plugs containing a wire fit down over the pins. The wire connects

the pins and creates a circuit. To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s) indicated. FigureA-1 shows an

example of a jumper.

Figure A-1. Example Jumpers



A jumper is referred to as open or unjumpered when the plug is pushed down over only one pin or if there is no plug at all. When the plug is pushed down

over two pins, the jumper is referred to as jumpered. The jumper setting is often shown in text as two numbers, such as 1–2. The number 1 is printed on the

circuit board so that you can identify each pin number based on the location of pin 1.



FigureA-2 shows the location and default settings of the system jumper blocks. See TableA-1 for the designations, default settings, and functions of the

system's jumpers.



System Board Jumpers



FigureA-2 shows the location of the configuration jumpers on the system board. TableA-1 lists the jumpers settings.

Figure A-2. System Board Jumpers



CAUTION: Ensure that the system is turned off before you change a jumper setting. Otherwise, damage to the system or unpredictable results

may occur.



Table A-1.SystemBoardJumperSettings



System Board Connectors



See FigureA-3 and TableA-2 for the location and description of system board connectors. FigureA-3 also indicates expansion slots and bus operating speeds.

Figure A-3. System Board Connectors



Jumper

Setting

Description

J11 pins 1 and



(default)

The password feature is enabled.



The password feature is disabled.

J11 pins 3 and



(default)

The configuration settings in NVRAM are retained at system boot.



The configuration settings in NVRAM are cleared at next system boot (see "Resetting Corrupted BIOS Configuration" in

"Troubleshooting Your System").

jumpered unjumpered



Table A-2. System Board Connectors



Disabling a Forgotten Password



Connector

Description

BATTERY

System battery

CHASSIS INTRUSION

Chassis intrusion switch

COM1/LPT/VGA

Serial, parallel, and video

CPUn

Microprocessors (2)

CPUnFAN

Microprocessor fan power (2)

DIMMx

Memory modules (4)

DRACIII/XT

Systems management

FDD

Diskette drive

FRONT PANEL

Front-panel switches and indicators

FRONT SYS FAN

Front system fan power

KB/MS

PS/2 keyboard and mouse

LAN

NIC

PRIMARY IDE

Primary IDE

PWR CONN

System board power

SCSI CONN

SCSI controller

SCSIB CONN

SCSI backplane

SECONDARY IDE

Secondary IDE

SLOTn

Expansion slots:

l1–2: 64-bit/66-MHz PCI

l3–4: 64-bit/100-MHz PCIX

l5–6: 32-bit/33-MHz PCI

REAR SYS FAN

Back system fan power

USB

USB (2)

12V

System board power

NOTE: For the full name of an abbreviation or acronym used in this table, see "Abbreviations and Acronyms."

The system's software security features include a system password and a setup password, which are discussed in detail in "Using the System Setup Program"

in your User's Guide. The password jumper enables these password features or disables them and clears any password(s) currently in use.



1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2. Remove the cover (see "Removing the Cover" in "Troubleshooting Your System").

3. Lay the system on its right side.

4. Remove the password jumper plug.



See FigureA-2 to locate the password jumper on the system board.

5. Stand the system upright.

6. Install the cover (see "Installing the Cover" in "Troubleshooting Your System").

7. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.



The existing passwords are not disabled (erased) until the system boots with the password jumper plug removed. However, before you assign a new

system and/or setup password, you must install the jumper plug.



8. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

9. Remove the cover (see "Removing the Cover" in "Troubleshooting Your System").

10. Lay the system on its right side.

11. Install the password jumper plug.



See FigureA-2 to locate the password jumper on the system board.

12. Stand the system upright.

13. Install the cover (see "Installing the Cover" in "Troubleshooting Your System").

14. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

15. Assign a new system and/or setup password.



To assign a new password using the System Setup program, see "Using the System Setup Program" in your User's Guide.

Back to Contents Page



CAUTION: Before you perform this procedure, see "Safety First—For You and Your System" in "Troubleshooting Your System."

CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information Guide.

NOTE: If you assign a new system and/or setup password with the jumper plug still removed, the system disables the new password(s) the next

time it boots.

Back to Contents Page



I/O Ports and Connectors

Dell™PowerEdge™1600SCSystemsInstallationandTroubleshootingGuide

I/O Connectors

Serial Connector

Parallel Connector

PS/2-Compatible Keyboard and Mouse Connectors

Video Connector

USB Connector

Integrated NIC Connector

Network Cable Requirements



I/O Connectors



I/O connectors are the gateways that the system uses to communicate with external devices, such as a keyboard, mouse, printer, or monitor. This section

describes the various connectors on your system. If you reconfigure the hardware connected to the system, you may also need the pin number and signal

information for these connectors. FigureB-1 illustrates the connectors on the system.

Figure B-1. I/O Connectors



TableB-1 shows the icons used to label the connectors on the system.



Table B-1. I/O Connector Icons

Icon

Connector



Serial connector



Parallel connector



Mouse connector



Keyboard connector



Video connector



USB connector



Serial Connector



Serial connectors support devices such as external modems, printers, and mice that require serial data transmission. The serial connector uses a 9-pin D-

subminiature connector.



Serial Connector Autoconfiguration



The default designation of the integrated serial connector is COM1. When you add an expansion card containing a serial connector that has the same

designation as the integrated connector, the system's autoconfiguration feature remaps (reassigns) the integrated serial connector to the next available

designation. Both the new and the remapped COM connectors share the same IRQ setting. COM1 and COM3 share IRQ4, while COM2 and COM4 share IRQ3.



Before adding a card that remaps the COM connectors, check the documentation that came with the software to make sure that the software can

accommodate the new COM connector designation.



FigureB-2 illustrates the pin numbers for the serial connector and TableB-2 defines the pin assignments for the connector.

Figure B-2. Serial Connector Pin Numbers



Table B-2. Serial Connector Pin Assignments



Parallel Connector



The integrated parallel connector, intended primarily for use by printers that require data in parallel format, uses a 25-pin D-subminiature connector on the

system's back panel. The default designation of the system's parallel connector is LPT1. If you add an expansion card containing a parallel connector

configured as LPT1 (IRQ7, I/O address 378h), use the System Setup program to remap the integrated parallel connector. See "Using the System Setup

Program" in the User's Guide. FigureB-3 illustrates the pin numbers for the parallel connector and TableB-3 defines the pin assignments for the connector.

Figure B-3. Parallel Connector Pin Numbers



NIC connector

NOTE: If two COM connectors share an IRQ setting, you may not be able to use them both at the same time. In addition, if you install one or more

expansion cards with serial connectors designated as COM1 and COM3, the integrated serial connector is disabled.

Signal

I/O

Definition

1

DCD

I

Data carrier detect

2

SIN

I

Serial input

3

SOUT

O

Serial output

4

DTR

O

Data terminal ready

5

GND

N/A

Signal ground

6

DSR

I

Data set ready

7

RTS

O

Request to send

8

CTS

I

Clear to send

9

RI

I

Ring indicator

Shell

N/A

Chassis ground



Table B-3. Parallel Connector Pin Assignments



PS/2-Compatible Keyboard and Mouse Connectors



The PS/2-compatible keyboard and mouse cables attach to 6-pin, miniature DIN connectors. FigureB-4 illustrates the pin numbers for these connectors and

TableB-4 defines the pin assignments for these connectors.

Figure B-4. Keyboard and Mouse Connector Pin Numbers



Table B-4. Keyboard and Mouse Connector Pin Assignments



Signal

I/O

Definition

1

STB#

I/O

Strobe

2

PD0

I/O

Printer data bit 0

3

PD1

I/O

Printer data bit 1

4

PD2

I/O

Printer data bit 2

5

PD3

I/O

Printer data bit 3

6

PD4

I/O

Printer data bit 4

7

PD5

I/O

Printer data bit 5

8

PD6

I/O

Printer data bit 6

9

PD7

I/O

Printer data bit 7

10

ACK#

I

Acknowledge

11

BUSY

I

Busy

12

PE

I

Paper end

13

SLCT

I

Select

14

AFD#

O

Automatic feed

15

ERR#

I

Error

16

INIT#

O

Initialize printer

17

SLIN#

O

Select in

18–25

GND

N/A

Ground

Signal

I/O

Definition

1

KBDATA or MFDATA

I/O

Keyboard data or mouse data

2

NC

N/A

No connection

3

GND

N/A

Signal ground

4

FVcc

N/A

Fused supply voltage

5

KBCLK or MFCLK

I/O

Keyboard clock or mouse clock

6

NC

N/A

No connection

Shell

N/A

Chassis ground

Video Connector



You can attach a VGA-compatible monitor to the system's integrated video controller using a 15-pin high-density D-subminiature connector. FigureB-5

illustrates the pin numbers for the video connector and TableB-5 defines the pin assignments for the connector.



Figure B-5. Video Connector Pin Numbers



Table B-5. Video Connector Pin Assignments



USB Connector



The system's USB connector supports USB-compliant peripherals such as keyboards, mice, and printers and may also support USB-compliant devices such as

diskette drives and CD drives. FigureB-6 illustrates the pin numbers for the USB connector and TableB-6 defines the pin assignments for the connector.



Figure B-6. USB Connector Pin Numbers



Table B-6. USB Connector Pin Assignments

NOTE: Installing a video card automatically disables the system's integrated video controller.

Signal

I/O

Definition

1

RED

O

Red video

2

GREEN

O

Green video

3

BLUE

O

Blue video

4

NC

N/A

No connection

5–8, 10

GND

N/A

Signal ground

9

VCC

N/A

Vcc

11

NC

N/A

No connection

12

DDC data out

O

Monitor detect data

13

HSYNC

O

Horizontal synchronization

14

VSYNC

O

Vertical synchronization

15

NC

N/A

No connection

NOTICE: Do not attach a USB device or a combination of USB devices that draw a maximum current of more than 500 mA per channel or +5 V. Attaching

devices that exceed this threshold may cause the USB connectors to shut down. See the documentation that accompanied the USB devices for their

maximum current ratings.

Signal

I/O

Definition

1

Vcc

N/A

Supply voltage

2

DATA

I

Data in

3

+DATA

O

Data out

4

GND

N/A

Signal ground



Integrated NIC Connector



The system's integrated NIC functions as a separate network expansion card while providing fast communication between servers and workstations. FigureB-

7illustrates the pin numbers for the NIC connector and TableB-7 defines the pin assignments for the connector.

Figure B-7. NIC Connector



Table B-7. NIC Connector Pin Assignments



Network Cable Requirements



The NIC supports a UTP Ethernet cable equipped with a standard RJ45-compatible plug. Observe the following cabling restrictions.



lUse Category 5 or greater wiring and connectors.

lDo not exceed a cable run length (from a workstation to a hub) of 100 m (328 ft).



For detailed guidelines on operation of a network, see "Systems Considerations of Multi-Segment Networks" in the IEEE 802.3 standard.

Back to Contents Page



Signal

I/O

Definition

1

TD+

O

Data out (+)

2

TD–

O

Data out (–)

3

RD+

I

Data in (+)

4

NC

N/A

No connection

5

NC

N/A

No connection

6

RD–

I

Data in (–)

7

NC

N/A

No connection

8

NC

N/A

No connection

NOTICE: To avoid line interference, voice and data lines must be in separate sheaths.

Otros manuales para PowerEdge 1600SC

Tabla de contenidos

Otros manuales de De oficina de Dell

Dell

Dell XPS Gen 3 Manual de usuario

Dell

Dell GX620 - 3.6GHz Desktop 1GB RAM 80GB Windows XP... Manual de usuario

Dell

Dell Dimension 07Y887A01 Manual de usuario

Dell

Dell 5820 Manual de usuario

Dell

Dell OptiPlex 9020 Manual de usuario

Dell

Dell OptiPlex GX50 Manual de usuario

Dell

Dell XPS 720 Manual de usuario

Dell

Dell Precision Tower 5810 Manual de usuario

Dell

Dell Precision PD055 Manual de usuario

Dell

Dell Precision N8151 Manual de usuario

Dell

Dell PowerEdge 1400 Manual de usuario

Dell

Dell Precision MD506 Manual de usuario

Dell

Dell OptiPlex 3000 Thin Client Manual de usuario

Dell

Dell OptiPlex 9010 AIO Manual de usuario

Dell

Dell XPS H2C Instrucciones de uso

Dell

Dell ChengMing 3900 Tower Manual de usuario

Dell

Dell 5820E Manual de usuario

Dell

Dell Inspiron 620 Manual de usuario

Dell

Dell OptiPlex 3010 Small Form Factor Manual de usuario

Dell

Dell OptiPlex 3011 AIO Manual de usuario

Dell

Dell XPS 8930 Manual de usuario

Dell

Dell Inspiron 2100 Guía del usuario

Dell

Dell OptiPlex 330 Manual de usuario

Dell

Dell Inspiron 2100 Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

HP Z1 Manual de usuario

Everex

Everex eXplora Manual de usuario

Lenovo

Lenovo ThinkCentre M75e Manual de usuario

Compaq

Compaq iPAQ Internet Device Manual de usuario