Dell Dimension 5100 Manual de usuario

Dell™Dimension™5100ServiceManual

Before You Begin

Removing the Computer Cover

AboutYourDell™Dimension™5100Computer

Advanced Troubleshooting

Removing and Installing Parts

Replacing the Computer Cover

Specifications

Technical Overview

System Setup

Notes, Notices, and Cautions

IfyoupurchasedaDell™nSeriescomputer,anyreferencesinthisdocumenttoMicrosoft®Windows®operating systems are not applicable.

Information in this document is subject to change without notice.

©2005DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and Dimension are trademarks of Dell Inc.; Intel and Pentium are registered trademarks of Intel Corporation; Microsoft and

Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Model DCSM

October2005Rev.A01

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

AboutYourDell™ Dimension™5100Computer

Dell™Dimension™5100ServiceManual

Front View of the Computer

Back View of the Computer

Front View of the Computer

cover latch

release

Use this latch to remove the computer cover.

location of

Service Tag

Use the Service Tag to identify your computer when you access the Dell

Support website or call technical support.

CD or DVD

eject button

Press to eject a disk from the CD or DVD drive.

CD or DVD

activity light

The drive light is on when the computer reads data from the CD or DVD

drive.

FlexBay

Can contain an optional floppy drive or optional Media Card Reader. For

more information about the Media Card Reader, see your computer

Owner's Manual.

microphone

connector

Use the microphone connector to attach a personal computer microphone

for voice or musical input into a sound or telephony program.

On computers with a sound card, the microphone connector is on the

card.

headphone

connector

Use the headphone connector to attach headphones.

diagnostic

lights (4)

Use the lights to help you troubleshoot a computer problem based on the

diagnostic code. For more information, see "Diagnostic Lights."

hard-drive

activity light

The hard drive activity light is on when the computer reads data from or

writes data to the hard drive. The light might also be on when a device

such as a CD player is operating.

power

button,

power light

Press the power button to turn on the computer. The power light in the

center of this button indicates the power state. See "Specifications" for

more information.



NOTICE: To avoid losing data, do not use the power button to turn off

the computer. Instead, perform an operating system shutdown.

USB 2.0

connectors

(2)

Use the front USB connectors for devices that you connect occasionally,

such as joysticks or cameras. It is recommended that you use the back

USB connectors for devices that typically remain connected, such as

printers, keyboards, and mice, or for bootable USB devices, which may

not function properly if attached to the front connectors.

vents

For adequate cooling, do not block any of the vents.



NOTICE: Ensure that there is a minimum of two inches of space between

all vents and any object near these vents.

Back View of the Computer



NOTICE: Do not lift or carry the computer by the vents to avoid damage

to the computer.



NOTICE: Keep the vent area clean and dust-free to ensure that the

computer is adequately ventilated. Use only a dry cloth to clean the vent

area to avoid water damage to the computer.

voltage selection switch (may not be available on all computers)

See the safety instructions in the Product Information Guide for more information.

power connector

Insert the power cable.

back panel connectors

Plug USB, audio, and other devices into the appropriate connector.

card slots

Access connectors for any installed PCI and PCI Express cards.

link integrity light

lGreen —A good connection exists between a 10-Mbps

network and the computer.

lOrange —A good connection exists between a 100-Mbps

network and the computer.

lOff —The computer is not detecting a physical connection

to the network.

network adapter

connector

To attach your computer to a network or broadband device,

connect one end of a network cable to either a network jack or

your network or broadband device. Connect the other end of the

network cable to the network adapter connector on the back

panel of your computer. A click indicates that the network cable

has been securely attached.



NOTE: Do not plug a telephone cable into the network connector.

On computers with a network connector card, use the connector

on the card.

It is recommended that you use Category 5 wiring and connectors

for your network. If you must use Category 3 wiring, force the

network speed to 10 Mbps to ensure reliable operation.

network activity light

Flashes a yellow light when the computer is transmitting or

receiving network data. A high volume of network traffic may make

this light appear to be in a steady "on" state.

Back to Contents Page



surround connector

Use the black surround connector to attach multichannel-capable

speakers.

line-in connector

Use the blue line-in connector to attach a record/playback device

such as a cassette player, CD player, or VCR.

On computers with a sound card, use the connector on the card.

line-out connector

Use the green line-out connector (available on computers with

integrated sound) to attach headphones and most speakers with

integrated amplifiers.

On computers with a sound card, use the connector on the card.

micro-phone/side

surround connector

Use the pink and silver connector to attach a personal computer

microphone for voice or musical input into a sound or telephony

program.

On computers with a sound card, the microphone connector is on

the card.

The side-surround output provides enhanced surround audio for

computers with 7.1 speakers.

center/subwoofer

connector

Use the yellow connector to attach a speaker to a Low Frequency

Effects (LFE) audio channel.

VGA video connector

If your monitor has a VGA connector, plug it into the VGA

connector on the computer.

USB 2.0 connectors

(5)

Use the back USB connectors for devices that typically remain

connected, such as printers, keyboards, and mice, or for bootable

USB devices which may not function properly if attached to the

front connectors (see "System Setup" for more information on

booting to a USB device)

It is recommended that you use the front USB connectors for

devices that you connect occasionally, such as joysticks or

cameras.

Back to Contents Page

AboutYourDell™ Dimension™5100Computer

Dell™Dimension™5100ServiceManual

Front View of the Computer

Back View of the Computer

Front View of the Computer

cover latch

release

Use this latch to remove the computer cover.

location of

Service Tag

Use the Service Tag to identify your computer when you access the Dell Support website or call technical support.

CD or DVD eject

button

Press to eject a disk from the CD or DVD drive.

CD or DVD

activity light

The drive light is on when the computer reads data from the CD or DVD drive.

FlexBay

Can contain an optional floppy drive or optional Media Card Reader. For more information about the Media Card Reader, see your

computer Owner's Manual.

microphone

connector

Use the microphone connector to attach a personal computer microphone for voice or musical input into a sound or telephony program.

On computers with a sound card, the microphone connector is on the card.

headphone

connector

Use the headphone connector to attach headphones.

diagnostic

lights (4)

Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see "Diagnostic

Lights."

hard-drive

activity light

The hard drive activity light is on when the computer reads data from or writes data to the hard drive. The light might also be on when

a device such as a CD player is operating.

power button,

power light

Press the power button to turn on the computer. The power light in the center of this button indicates the power state. See

"Specifications" for more information.



NOTICE: To avoid losing data, do not use the power button to turn off the computer. Instead, perform an operating system

shutdown.

USB 2.0

connectors (2)

Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras. It is recommended that you use

the back USB connectors for devices that typically remain connected, such as printers, keyboards, and mice, or for bootable USB

devices, which may not function properly if attached to the front connectors.

vents

For adequate cooling, do not block any of the vents.



NOTICE: Ensure that there is a minimum of two inches of space between all vents and any object near these vents.



NOTICE: Do not lift or carry the computer by the vents to avoid damage to the computer.



Back View of the Computer

NOTICE: Keep the vent area clean and dust-free to ensure that the computer is adequately ventilated. Use only a dry cloth to

clean the vent area to avoid water damage to the computer.

voltage selection switch (may not be available on all computers)

See the safety instructions in the Product Information Guide for more information.

power connector

Insert the power cable.

back panel connectors

Plug USB, audio, and other devices into the appropriate connector.

card slots

Access connectors for any installed PCI and PCI Express cards.

link integrity light

lGreen —A good connection exists between a 10-Mbps network and the computer.

lOrange —A good connection exists between a 100-Mbps network and the computer.

lOff —The computer is not detecting a physical connection to the network.

network adapter

connector

To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or

your network or broadband device. Connect the other end of the network cable to the network adapter connector on the back

panel of your computer. A click indicates that the network cable has been securely attached.



NOTE: Do not plug a telephone cable into the network connector.

On computers with a network connector card, use the connector on the card.

It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force

the network speed to 10 Mbps to ensure reliable operation.

network activity light

Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make

this light appear to be in a steady "on" state.

surround connector

Use the black surround connector to attach multichannel-capable speakers.

line-in connector

Use the blue line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.

On computers with a sound card, use the connector on the card.

line-out connector

Use the green line-out connector (available on computers with integrated sound) to attach headphones and most speakers

with integrated amplifiers.

On computers with a sound card, use the connector on the card.

micro-phone/side

surround connector

Use the pink and silver connector to attach a personal computer microphone for voice or musical input into a sound or

telephony program.

On computers with a sound card, the microphone connector is on the card.

Back to Contents Page



The side-surround output provides enhanced surround audio for computers with 7.1 speakers.

center/subwoofer

connector

Use the yellow connector to attach a speaker to a Low Frequency Effects (LFE) audio channel.

VGA video connector

If your monitor has a VGA connector, plug it into the VGA connector on the computer.

USB 2.0 connectors (5)

Use the back USB connectors for devices that typically remain connected, such as printers, keyboards, and mice, or for

bootable USB devices which may not function properly if attached to the front connectors (see "System Setup" for more

information on booting to a USB device)

It is recommended that you use the front USB connectors for devices that you connect occasionally, such as joysticks or

cameras.

Back to Contents Page

Before You Begin

Dell™Dimension™5100ServiceManual

Getting Started

Recommended Tools

Turning Off Your Computer

Before Working Inside Your Computer

Getting Started

This section provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the

following conditions exist:

lYou have performed the steps in "Turning Off Your Computer" and "Before Working Inside Your Computer."

lYouhavereadthesafetyinformationinyourDell™Product Information Guide.

lA component can be replaced by performing the removal procedure in reverse order.

Recommended Tools

The procedures in this document may require the following tools:

lSmall flat-blade screwdriver

lPhillips screwdriver

lFlash BIOS update program floppy disk or CD

Turning Off Your Computer



1. Shut down the operating system:

a. Save and close any open files, exit any open programs, click the Start button, and then click Turn Off Computer.

b. In the Turn off computer window, click Turn off.

The computer turns off after the operating system shutdown process finishes.



2. Ensure that the computer and any attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut

down your operating system, press and hold the power button for 4 seconds.

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.



1. Turn off your computer.

NOTICE: To avoid losing data, save and close any open files and exit any open programs before you turn off your computer.

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal

mounting bracket. Hold a component such as a processor by its edges, not by its pins.

NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not

covered by your warranty.

NOTICE: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with

locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and

aligned.

NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer.

NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network port or device.



2. Disconnect any telephone or telecommunication lines from the computer.



3. Disconnect your computer and all attached devices from their electrical outlets, and then press the power button to ground the system board.



4. Remove the computer cover.

Back to Contents Page



CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.

NOTICE: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the

computer. While you work, periodically touch an unpainted metal surface to dissipate any static electricity that could harm internal components.

Back to Contents Page

Before You Begin

Dell™Dimension™5100ServiceManual

Getting Started

Recommended Tools

Turning Off Your Computer

Before Working Inside Your Computer

Getting Started

This section provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the

following conditions exist:

lYou have performed the steps in "Turning Off Your Computer" and "Before Working Inside Your Computer."

lYouhavereadthesafetyinformationinyourDell™Product Information Guide.

lA component can be replaced by performing the removal procedure in reverse order.

Recommended Tools

The procedures in this document may require the following tools:

lSmall flat-blade screwdriver

lPhillips screwdriver

lFlash BIOS update program floppy disk or CD

Turning Off Your Computer



1. Shut down the operating system:

a. Save and close any open files, exit any open programs, click the Start button, and then click Turn Off Computer.

b. In the Turn off computer window, click Turn off.

The computer turns off after the operating system shutdown process finishes.



2. Ensure that the computer and any attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut

down your operating system, press and hold the power button for 4 seconds.

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.



1. Turn off your computer.

NOTICE: To avoid losing data, save and close any open files and exit any open programs before you turn off your computer.

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal

mounting bracket. Hold a component such as a processor by its edges, not by its pins.

NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not

covered by your warranty.

NOTICE: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with

locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and

aligned.

NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer.

NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network port or device.

Otros manuales para Dimension 5100

Tabla de contenidos

Otros manuales de De oficina de Dell

Dell

Dell OPTIPLEX 9010 ALL-IN-ONE Manual de usuario

Dell

Dell Inspiron 20 Manual de usuario

Dell

Dell INSPIRON DCMF Manual de lista de piezas

Dell

Dell Vostro 3910 Manual de operación y mantenimiento

Dell

Dell OptiPlex 3080 Small Form Factor Cable Cover Manual de operación y mantenimiento

Dell

Dell OptiPlex 990 Desktop Manual de usuario

Dell

Dell OptiPlex Small Form Factor 7010 Manual de usuario

Dell

Dell Inspiron 1420 Instrucciones de uso

Dell

Dell Latitude 3440 Guía del usuario

Dell

Dell Inspiron 530sa Manual de usuario

Dell

Dell Optiplex-620 Manual de usuario

Dell

Dell XPS 8900 Manual de usuario

Dell

Dell vostro Manual de usuario

Dell

Dell Dimension 3100/E310 Manual de usuario

Dell

Dell OptiPlex 5040 Series Manual de usuario

Dell

Dell Inspiron 3252 Manual de usuario

Dell

Dell OptiPlex 3070 Small Form Factor Manual de operación y mantenimiento

Dell

Dell Vostro 3650 Manual de usuario

Dell

Dell OptiPlex 330 Manual de usuario

Dell

Dell Alienware Aurora R15 Manual de usuario

Dell

Dell OptiPlex 9020 Manual del propietario

Dell

Dell ALIENWARE AURORA - GAMING MACHINE - ALIENWARE... Manual de usuario

Dell

Dell Precision WorkStation Vostro 220 System Manual de usuario

Dell

Dell OptiPlex 3080 Micro Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

HP Z1 Manual de usuario

Everex

Everex eXplora Manual de usuario

Lenovo

Lenovo ThinkCentre M75e Manual de usuario

Compaq

Compaq iPAQ Internet Device Manual de usuario