DECKED MT5 Manual de usuario
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 1
Watchshortinstallationvideosatwww.decked.com/video|Register yoursystem at www.decked.com/warranty
Installation Instructions:
MT5 / MT7
TOOLS REQUIRED
TOYOTA TACOMA
5'1” BED LENGTH
MT5 20052018 / MT7 2019CURRENT
VERSION1.1
DECKED.COM | 208.806.0251
@DECKEDUSA | #DECKEDUSA
FOLLOW US:
• Adjustable wrench (that opens to about 1”)
• 1/2” open end wrench
• #2 Phillips screwdriver,
• Short 7/32” hex wrench
• 7/16” deep socket
• 3/8” socket
• Electric drill
• 9/64" drill bit
• 1/4” drill bit
• 5/16" drill bit
• Drill stop
• T40 Torx Driver
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 2
CAB
▼ ASSEMBLY OVERVIEW ▼
CENTER VERT
CABSIDE VERT
LEFT DECK
(NARROW)
RIGHT DECK
(WIDE)
LEFT AMMO
CAN
RIGHT AMMO
CAN
LEFT STUD
RIGHT STUD
LEFT AMMO
CAN LID
RIGHT AMMO CAN LID
TORSION
BRACE
RIGHT
CCHANNEL
LEFT
CCHANNEL
TAILGATE
CONTENTS
DECKED carton
LEFT deck half - 1
RIGHT deck half - 1
Center vert - 1
Cabside vert - 1
Drawer - 2
Left ammo can - 1
Right ammo can - 1
Left stud - 1
Right stud - 1
Ammo can lid - 2
C-channel - 2
Ruler - 1
Hardware box - 1
Bottle opener - 1
Torsion brace - 1
Hardware box - unbagged components
(inside DECKED carton):
Shims - 4
Weather strips - 2
HARDWARE box - bagged components
PREP-MT5 or MT7 - 1
S1 1
S2 - 1
N1 - 1
J4 - 2
DRAWER 1 1
DRAWER 2 1
WHEELS 1
FINAL MID 1
PREPEXTRA 1
MS WASHERS 1
(MT7 ONLY) TACOMA TD 1
RULER
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 3
▼ ASSEMBLY OVERVIEW ▼
▼ HEY! TORQUE BOY: READ BEFORE YOU INSTALL DECKED ▼
1. DON’T be anidiotread the instructions.
2. DON'T over tightenbolts,getem' hand-tight.
3. DON'Tuse powertools.
4. Ifyoudon't followdirectionsand
do
usepowertools:
1). Setclutchat a verylowsetting. 2). If you blowit,seeNOTE.*
NOTE*Twoextrathreadedinsertsareincluded inBAG PREP-EXTRA. That’s allyouget. Theinsertswillreplaceany
strippedinsertsin the tailgate ammocans, but NOTTHECENTER VERT, sohand tighten until snugonly! Youcan
alsoscrewthe insertsback in ifdislocated.Thereis astraightscrewdriver slotonthe undersideofthe insert.
5. Startallboltswithfingerstoavoid cross-threading
6. DON'T over tightenJ-hooksduring installation.
Make 'emgood and snug enoughtokeepthe
systemfrommovingin the bed.
7. Nicejob if you’restillreading.
Prevent abusive, expletitive-filled language, watch our detailed installation video
or give us a call. We’re happy to help!
208.806.0251 | DECKED.COM/INSTALLVIDEO
A
CAB
➡
MAKE SURE MARK SITS AT LEAST
14" HIGH (SO YOU CAN SEE IT)
DETAIL A
PREP BED: MARKCENTEROFBED
• Usea marking pen orwaxpenciltomark
thecenterofthe bed (blue)onthe raisedbead.
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 4
DETAIL A
Alignshimtochannelin floorshown 3”from
cabsidepanelofbed(red).
DETAIL B
Alignshimtochannelin floorshown. Place
shim6 1/2”fromrear ofbed (red).
3”
6 1/2”
A
B
PLACE LARGE SHIM OVER FACTORY BED BOLT
AS SHOWN. REPEAT PASSENGER SIDE.
➡
CAB
PREP BED: SHIMS
• 2 SMALL shimsand2 LARGE shims(with holes)arelooseinyourhardwarekit.
• Usingthe informationbelow:
1) Cleanthe bedsurfacewheretheshims willbelocated.Isopropylalcohol(do notdrink) is recommended.
2) Remove tapefilmand apply shim withthestrengthof 1000mena.k.a push reallyhard.
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 5
PREP BED: TAILGATEBRACKET
NOTE: You will need to grab a pal for this step (or have incredibly long and flexible arms).
• Remove toprearfactorycompartment boltfromthepassengerside with a T40TorxDriver.Keepbolt.
• Looselyattach passanger sidetailgate bracket with factory bolt in top hole. Make sure the tie down opening is
angled toward the driver, not the tailgate; BAG PREP-MT5 or MT7.
• Alignbracket so it'sparallelwithverticaledge ofcompartment.Tightenfactorybolt atlast!
• Usingthebottomholeinbracketasa guide,drill a5/16"holewitha1/2" drillstopthroughcompartmentandbedwall.
• Installa1" bolt throughthe bracketandbed wall. Install1"washerandflanged nut and tightensecurely;
BAG PREP-MT5 or MT7.
• Repeatdriverside unlessyoudon'thave a driver'sside cubby. If not,follow the instructionsfordriver'ssideon
nextpage.NOTE: On passenger side ONLY, you will need to add a washer; BAG PREP-MT5 or MT7...
We know it's strange, trust us.
DRIVER SIDE
FACTORY BOLT
PASSENGER SIDE
HELPFUL TIP: Feel free to remove doors of cubbies
so you can still somewhat use them. Use will be
compromised, but hey, life ain't always fair, right?!
HELPFUL TIP:The power outlet can stillbe used if you
inserta flat head pigtail extensioncordBEFORE you
installthe decks.Makesureto havethe outletcapped
to keep water out.
ANGLE TIEDOWN
TOWARD DRIVER
➡
CAB
➡
CAB
FLANGED
NUT
WASHER
FLANGED
NUT
REALLY OLD DRILL
WE FOUND ONLINE
1" BOLT
1" BOLT
RECOMMENDED TORQUE:
Bolts in labeled bag PREP-MT5 or MT7 - 53 in-lb.
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 6
PREP BED: TAILGATEBRACKET
(FOR TACOMAS WITH NO DRIVER SIDE TAILGATE CUBBY)
NOTE:DisregardthispageifyouHAVEadriver'ssidetailgatecubby.
• ReferencingdimensionalinfoinDETAILAmarkholelocationsanddrill(2)5/16"holes(withdrillstopsetat.62").
• Referencing DETAIL A install J-hook mounting bracketas shownwith bolts,backing plateand nuts.
Tighten bolts securely. BAGPREP-MT7,BAG TACOMA TD.
DETAIL A
DRIVER'S SIDE ONLY
HOLE DRILLING
DETAIL A
DRIVER'S SIDE ONLY
BOLT INSTALLATION
DRILL 5/16" HOLE 2 PLACES
DRILL STOP
5/16" DRILL BIT
.62"
2.75"
7.5" TO
BOTTOM
OF BED
5.75" FROM
REAR OF BED BOLT
BACKING
PLATE
NUT
DETAIL A
RECOMMENDED TORQUE:
Bolts in labeled bag PREP-MT7 - 53 in-lb.
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 7
ASSEMBLY: CENTERVERT+CABSIDEVERT
NOTE: Perform the next few steps on a flat surface like a garage floor.
• Attach centerverttocabside vert with fourbolts.Alternate to tighten; BAG S1.
CENTER VERT
CABSIDE VERT
S1
PLACEHOOKONCENTER VERT
OVERNOTCHIN CABSIDEVERT
HELPFUL TIP: BAG S1, a.k.a "Bunker Hill,"is required
for most of the steps, so keep it close! These bolts are
highlighted throughout instructions in RED.
RECOMMENDED TORQUE:
Bolts in labeled bag S1 - 27 in-lb.
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 8
ASSEMBLY: LOOSELYATTACHSTUDS(YUP)
• LOOSELY attachstudstocabside vertwith sixbolts;BAG S1.
CENTER VERT
PASSENGER
SIDE STUD
CABSIDE VERT
DRIVER
SIDE STUD
KEEP LOOSE
(YOGAHELPS)
S1 KEEP LOOSE
S1
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 9
HELPFUL TIP: This step seems like a waste of time,
but Dr. DECKED says it's important...don't skip out.
ASSEMBLY: ALIGN&TIGHTENSTUDS(YUP)
NOTE: This step ensures the studs are properly located before tightening bolts. It's important.
• Placeammocanstosupporttailgateendofdeckpanels.
• Liftdeckpanelsoncentervert+stud+cabsidevertassembly.
• SlidestudsaroundL-Runtildeckpanelsareseated.
• DETAILA:Looselysecurefourboltstoholddecksontostuds; BAGS1.
• Nowyoucansecurelytightentheboltsthatholdthestudstothecabsidevert.
• Unboltdeckfromstuds,removedeckpanels,savebolts,removeammocansandsetasideforlaterassembly.
DETAIL A
S1
A
YOU WILL REMOVE AND SAVE THESE BOLTS
AFTER TIGHTENING CABSIDE VERT + SHIM
BOLTS
TIGHTEN AND SECURE RECOMMENDED TORQUE:
Bolts in labeled bag S1 - 27 in-lb.
DECKED.COM |#DECKEDUSA |@DECKEDUSA MT5 / MT7 | v.1.1 | Page 10
STUD BRACKET
TOP HOLE
CABSIDE BRACKET
(GREY)
STEP 1 STEP 2
NOTE: Make sure centerline arrows on
cabside vert are aligned with your
centerline mark (blue).
STEP 3
KEEP LOOSETIGHTEN
THREE
3 1/2"
BOLTS
3/4" BOLT
CAB
➡
➡
CAB
ASSEMBLY: BRACKETS+MOUNTING
• STEP1:Securely attach studbracket todriverside stud usingthree3 1/2"boltsandthreeflanged nuts;
BAG PREP-MT5 or MT7.
• STEP 2: Loosely attachcabsidebracket tothe tophole in studbracket with 3/4"bolt and flanged nut;
BAG PREP-MT5 or MT7. KEEP LOOSE.
• Repeat STEP 1 and STEP 2 on passenger side.
• STEP 3: While supporting both ends, lift center vert + stud + cabside vert assembly in truck bed.
FLANGED NUT
➡
CAB
FLANGED
NUTS
RECOMMENDED TORQUE:
For all fasteners - 27 in-lb.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios para automóviles de DECKED
DECKED
DECKED DS1 Manual de usuario
DECKED
DECKED VAN SHELVING Manual de usuario
DECKED
DECKED DR6 Manual de usuario
DECKED
DECKED Slide Guía de referencia
DECKED
DECKED MT6 Manual de usuario
DECKED
DECKED LADDER Manual de usuario
DECKED
DECKED TOOL BOX Manual de usuario
DECKED
DECKED MG3 Manual de usuario
DECKED
DECKED DS1 Manual de usuario
DECKED
DECKED ToolBox Ladder Bracket Manual de usuario
