Danfoss RET2001RF Manual de usuario

Installation Guide

RET2001RF & TP5001RF

RF Room & Programmable Room Thermostats

www.danfoss.com

AN30483490055001-000103 RET2001RF & TP5001RF2

Installation Guide

Full product instructions can be be found at www.danfoss.

com

SIMPLIFIED EU DECLARATION OF CONFORMITY

The simplied EU declaration of conformity referred to in

Article 10(9)

shall be provided as follows:

Hereby, Danfoss A/S declares that the radio equipment type

RET2001RF and TP5001RF are in compliance with Directive

2014/53/EU. The full text of the EU declaration of conformity

is available at the following internet address:

https://assets.danfoss.com/approvals/latest/200388/

ID365935467494-0301.pdf

Danfoss Climate Solutions AN30483490055001-000103 3

Installation Guide ...................................4 EN

Manuel d’installation...............................10 FR

Installationsanleitung ..............................16 DE

Installatiehandleiding ..............................22 NL

Installationsvejledning .............................28 DK

Guía de instalación.................................34 ES

Guida all’installazione ..............................40 IT

Kurulum Kılavuzu ..................................46 TR

Montavimo vadovas ...............................52 LT

   ........................58 RU

Illustrations ...................................64

Installation Guide

AN30483490055001-000103 RET2001RF & TP5001RF4

1. Installation Steps

User Guide can be downloaded from: heating.danfoss.com.

1. Installation must be done by an authorised

electrician.

2. The room thermostat should be installed at approx.

1.5 m above oor and where the eects of sunlight,

draught or other heat sources (eg. TV’s) are avoided,

see g. 1 on page 64.

3. Decide location of RX1-S V2 receiver, ensuring a

minimum space of 30cm from boiler housing. There

must be no large metal objects, such as boiler cases

or other large appliances, in line of sight between

the thermostat and the receiver as this will prevent

RF communication, see g. 1 on page 64.

4. Remove and mount RX1-S V2 back plate direct

to wall or on wall box, and wire as required for

application, see g. 2 on page 64.

5. Locate hooks at top of RX1-S V2 into top of back

plate and lower into position and tighten retaining

screw. Switch on mains power to start RF pairing.

6. Loosen lower retaining screw of thermostat and

carefully remove back plate, see g. 3 on page 64.

7. Insert 2 x AA Alkaline batteries to front part taking

care to insert correctly as indicated. Check RF

connection between Thermostat and RX1-S V2

Receiver before xing in nal position, see RF Pairing

below.

Installation Guide

Danfoss Climate Solutions AN30483490055001-000103 5

Installation Guide

8. Mount back plate direct to wall or on wall box. The

backplate included within the product packaging

should be used for the installation.

9. Locate hooks at top of front part into top of back

plate and lower into position and tighten retaining

screw.

2. Dimensions and Wiring

See g. 4 for dimensions and g. 5 for wiring diagram

on page 65.

AN30483490055001-000103 RET2001RF & TP5001RF6

3.1 RF Pairing

1. Ensure power to RX1-S V2 receiver is switched on

and batteries are inserted into thermostat.

2. Ensure the display is illuminated. If not, press any

button once to illuminate.

3. Press and hold M button on thermostat for 6

seconds until display changes to show setting

options.

4. Release and press M button to navigate through

menu until setting option 10 is shown.

5. Press > button to change setting to 01.

6. Press the upper part of the setting ring for

RET2001RF and for TP5001RF to accept

the setting. RF aerial icon will ash to indicate

thermostat is in learn mode.

7. Press both PROG and CH buttons on RX1-S V2 until

button LEDs ash.

8. If pairing is successful RF icon on thermostat will

stop ashing and remain on.

9. If pairing is not successful, try moving thermostat to

alternative position and retry.

Installation Guide

Danfoss Climate Solutions AN30483490055001-000103 7

Installation Guide

3.2 Legacy - RF Pairing

Use this guide when replacing the RF thermostat only,

existing RX1-S (087N7774) is used for receiver. If both

products are changed follow normal pairing procedure,

see 3.1 RF Pairing, page 6.

• RET2001RF (087N6473)

• TP5001RF (087N7933)

1. Ensure power to the RX1-S receiver is switched on

and batteries are inserted into the thermostat.

2. Ensure the display is illuminated, if not, press any

button once to illuminate it.

3. Press and hold <and Mfor 5 seconds, the RF aerial

icon will start ashing on the thermostat until

paired.

4. Press both PROG and CH buttons on RX1-S until

button LEDS ash.

5. If pairing is successful RF icon on thermostat will

stop ashing and remain on.

6. If pairing is not successful, try moving thermostat to

alternative position and retry.

AN30483490055001-000103 RET2001RF & TP5001RF8

EN 4. Error codes

Display Description

E1 Sensor Failure

EE EEPROM Failure

Lo Measured temperature below 0 °C

Hi Measure temperature above 50 °C

E3 RF Pairing Failed

E4 RF Signal Lost

E5 RF Hardware Failure

E6 Real Time Clock Failure(TP5001RF Only)

5. Technical Specications

Specications RET2001RF /

TP5001RF RX1-S V2

Operating Product is designed

forcontinuoususe

Operating Voltage 2.5–3VDC

(2 x AA alkaline

batteries)

230Vac

50/60Hz

Output - Volt free

Setting temperature

range 5 °C to 35 °C -

Operating temperature

range 0 °C to 40 °C

Installation Guide

Danfoss Climate Solutions AN30483490055001-000103 9

Specications RET2001RF /

TP5001RF RX1-S V2

Battery life 2 years -

Switch rating - 3A (1) at

250Vac

Switch type - 1x SPDT Type

1B

Terminals 1 to 2.5 mm wires

IP rating IP30 (installed)

Load compensation

control Yes -

On/o control Yes -

ErP class Class IV, ef-

ciency gain

2% -

Construction EN60730-2-9 EN60730-1

Pollution degree rating Degree 2

Rated impulse voltage - 4kV

Ball pressure test 75 °C

Dimensions H86 x W86 x

D30 H84 x W84 x

D30

Software classication A

Operating Frequency 433.100-434.750MHz

Maximum radio-

frequency power

transmitted 10dBm

Running and setting

accuracy (forthermostats

with build in timer)

Setting resolution 1 minute.

Accuracy +/- 1 minute per

month.

Installation Guide

AN30483490055001-000103 RET2001RF & TP5001RF10

1. Étapes d’installation

Le guide de l’utilisateur peut être téléchargé sur: heating.danfoss.com.

1. L’installation doit être réalisée par un électricien

agréé.

2. Le thermostat d’ambiance doit être installé à environ

1,50m au-dessus du sol et à l’écart du rayonnement

solaire, des courants d’air et d’autres sources

dechaleur ( téléviseurs, etc.) (voir g. 1 à la page 64).

3. Choisissez l’emplacement du récepteur RX1-S V2,

enassurant un espace minimum de 30cm par rapport

aucapot métalliquede la chaudière. Il ne peut y avoir

de gros objets métalliques, tels que des enveloppes

de chaudière ou d’autres gros appareils, dans la

ligne de visée du thermostat et du récepteur, car ils

risquent d’empêcher la communication radio (RF)

(voir g. 1 à la page 64).

4. Retirez et montez la plaque arrière RX1-S V2

directement au mur ou sur le boîtier mural et câblez

selon les besoins de l’application.

5. Repérez les crochets au sommet du RX1-S V2 dans

lehaut de la plaque arrière, abaissez-les pour

lespositionner et serrez la vis de retenue. Activez

l’alimentation secteur pour démarrer l’appairage RF.

6. Desserrez la vis de retenue inférieure du thermostat

etretirez soigneusement la plaque arrière (voir g. 2

à la page 64).

Manuel d’installation

Otros manuales para RET2001RF

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss TP5000 RF Si Guía

Danfoss

Danfoss ST-D1 Manual de usuario

Danfoss

Danfoss TP75 Manual de funcionamiento

Danfoss

Danfoss DEVIreg 233 Manual de usuario

Danfoss

Danfoss C37 Manual de usuario

Danfoss

Danfoss HP8211-1RJ Manual de usuario

Danfoss

Danfoss RET2001RF Manual de usuario

Danfoss

Danfoss FH-CWT Manual de usuario

Danfoss

Danfoss Icon Master Manual de usuario

Danfoss

Danfoss KPU 19 Manual de usuario

Danfoss

Danfoss living connect Z Manual de usuario

Danfoss

Danfoss FP975 Manual de usuario

Danfoss

Danfoss Devireg 535 Instrucciones de uso

Danfoss

Danfoss FP715Si Manual de usuario

Danfoss

Danfoss HC75A-1 Manual de funcionamiento

Danfoss

Danfoss RET2000 M Manual de usuario

Danfoss

Danfoss Icon Master Manual de usuario

Danfoss

Danfoss TP9000 Guía

Danfoss

Danfoss 103E5 Manual de usuario

Danfoss

Danfoss ECtemp 316 Manual de usuario

Danfoss

Danfoss TP9 Manual de usuario

Danfoss

Danfoss TP7001 series Manual de usuario

Danfoss

Danfoss Link FT Manual de usuario

Danfoss

Danfoss RET 230 HC-1 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario