Danfoss FP715 Instrucciones de montaje

FP715 Electronic 2-channel

full programmer for

heating & hot water

Installation & User Instructions

Index

Installation

Product speciﬁcation 3

Installation 4

Wiring 5

DIL switch settings 5

Wiring Conversion 6-13

User

Your programmer 14

Preset programmes 14

Resetting the unit 15

24hr or AM/PM display 15

Setting the Time and Day 15-16

Accepting the preset programmes 16

Changing the preset programmes 17

Programming heating - 5/2 day 18-19

Programming heating - 7 day 20-21

Programming heating - 24 hour 22

Programming hot water 23

Running the programme 24

Temporary overrides 25

Changing clocks forward/back 26

Troubleshooting 27

Contact details 28

Central Heating

1HR override

Central Heating

MAN override

RESET

Central Heating

Mode SELECT

+1HR

MAN

+1HR

MAN

Hot Water

1HR override

Hot Water

MAN override

Hot Water

Mode SELECT

INDEX

Installation & Speciﬁcation

Please Note:

This product should only be installed by a qualiﬁed

electrician or competent heating installer, and

should be in accordance with the current edition of

the IEEE wiring regulations.

Speciﬁcation

Power supply 230 Vac, ±10%, 50/60 Hz

Switching action

2 x SPDT internally linked, Type 1B

Switch rating 230 V ac, 3(1)A

Battery back-up 24 hours minimum

Programme resolution 1 minute

Dimensions, mm (W, H, D) 135 x 88 x 32

Design standard EN 60730-2-7

Control Pollution Situation Degree 2

Rated Impulse Voltage 2.5kV

Ball Pressure Test 75°C

Product speciﬁcation

Installation Instructions

Installation

 Remove wallplate from unit by unscrewing the two

screws on the bottom edge of the unit.

From the top left hand corner of the wallplate, there

must be clearances of at least 140 mm to the right,

15mm to the left, 30mm above and 100mm below in

order to mount the plug-on module.

The wallplate must be securely mounted either directly

to the wall using suitable wood screws or to a ﬂush

mounted 1-gang electrical accessory box using M3.5

screws.

Cable access can either be from behind for concealed

cabling, or from below for surface cabling. If surface

cable is used, cut out cable access slot on plug-on

module prior to mounting the module.

For wiring connections refer to diagram on page 5.

FP715 models are double insulated and do not require

an earth connection, however a parking terminal is

provided on the wallplate. This is clearly marked with

an Earth symbol.

Prior to mounting the plug-on module, DIL switches

on the rear of the plug-on module must be set. See

diagram on page 5 for available options.

Mount plug-on module to wallplate by locating tabs on

top of wallplate in apertures on rear of module, hinge

down and press ﬁrmly to wallplate before tightening

securing screws on bottom of wallplate.

Installation

CP715 FP715 (3028 12/01)

2 ON/OFFs

PUMPED

7 DAY or 24 HOUR

24 HOUR

3 ON/OFFs

GRAVITY

5/2 DAY

7 DAY

SW.1

SW.2

SW.3

SW.4

Wiring & DIL switch settings

Wiring

Always switch off mains ﬁrst and never ﬁt

programmer to a live wallplate.

For Wiring Conversion tables see - pages 6-13

Remember to tick the

INSTALLER SETTING box on

the inside ﬂap label to notify

user in which

mode their unit

is set (24hr, 5/2

day or 7 day).

DIL Switch Settings

Before mounting the unit, ensure

the 4 DIL switches on the rear of

the unit have been moved to the

required settings

INSTALLER SETTING

24 Hour

5+2 Day

7 Day

WIRING CONVERSIONS

Wiring conversions can be used when replacing the following programmers

with the FP715. Some time controls are connected differently depending on

the type of system they are controlling. Consult the column headed “NOTE

Table A

DANFOSS RANDALL

FP715, CP715

(PUMPED)

MAINS DHW

OFF

HTG

OFF

DHW

NL12 3

DANFOSS RANDALL 922/972 NL14 3

DANFOSS RANDALL 4033 7653 4

DANFOSS RANDALL SET 5 NL36 1

HORSTMANN 423, AMETHYST 7 & 10 2,3 1 4 6 5

HORSTMANN 424 GEM 2,3 1,10 6 9 4

HORSTMANN LEUCITE 423 & 424 2148 3

HORSTMANN 425 DIADEM NL36 1

HORSTMANN 525 & 527 NL36 1

HONEYWELL ST669 NL74 6

HONEYWELL ST6300 & ST6400 NL12 3

PEGLER SUNVIC SP50/SP100 NL14 2

POTTERTON EP2000, EP3000 NL12 3

RANDALL TSR3+3 3,6 7 2 5 1

RANDALL 3033 1,7 6 5 3 4

RANDALL 702 NL42 3

SANGAMO FORM 1 410 & 414 4,5 6 2 7 1

SANGAMO S409/1 N,1,3 L - - 2

This conversion ...” to determine whether Table A (pages 6-9) or Table B

(pages 10-13) should be used. If in any doubt, contact our Technical Services

Department before proceeding with the replacement. *Any wires connected

to switch COMMONS which are linked LIVE on existing wallplates must be

transferred to the LIVE terminal on the new wallplate.

HTG

Wires other

than links

in these

terms got

to LIVE

NOTE

This conversion applies

only if....

An additional terminal

block may be required

where these discon-

nected leads (or pairs)

should be terminated

4LL

ABCD

625 Programmed

selectors UNLINKED

21-

425

7-- 8

7 5 8 Terminals 5,8 & 10 are LINKED

6 5 7 Terminals 5 & 7 are LINKED

425 Programme

selectors UNLINKED

425 Programme

selectors UNLINKED

385

4--

53- SS

4-5 Programme

selectors UNLINKED ABCD

4--

2--

165

83-

5--

Table A cont..

DANFOSS RANDALL

FP715, CP715

(PUMPED)

MAINS DHW

OFF

HTG

OFF

DHW

NL12 3

SANGAMO S409/3 3,6 7 4 2 5

SATCHWELL LIBRA & DHP 2201 1285 6

SATCHWELL ET 1401 & 1451 1285 7

SMITHS IND. CENTROLLER 90 12- - 5

SMITHS IND. CENTROLLER 1000 NL12 3

SWITCHMASTER 800 & 805 NL42 3

SWITCHMASTER 900 & 9000 NL42 3

SWITCHMASTER SONATA NL36 1

VENNER CHC/W2 (WITH STAT) N,2,4 L - - 1

VENNER CHC/W2 (AIR STAT LINKED) N,2,4 L - - 1

VENNER VENOTROL 80M & 80PM

(WITH AIR STAT) N,3 L 1 4 2

VENNER VENOTROL 80M & 80PM

(AIR STAT LINKED) N,3 L 1 4 2

HTG

Wires other

than links in

these terms

got to LIVE

NOTE

This conversion applies

only if....

An additional terminal

block may be required

where these discon-

nected leads (or pairs)

should be terminated

4LL

ABCD

1--

374

463

4-- 36

4-- Programme

selectors UNLINKED

1--

1-- Programme

selectors UNLINKED ABC

4--

A/S - - Used in a system having

independent control of water

and heating

A/S

3--

A/S - - A/S

5--

Table B

DANFOSS RANDALL

FP715, CP715

(PUMPED)

MAINS DHW

OFF

HTG

OFF

NL12

DANFOSS RANDALL 922/972 NL14

DANFOSS RANDALL 102/102E/102E7 5 3,6 - -

HORSTMANN 423 DIAMOND POTTERTON 423 N L,1,3 - -

HORSTMANN 424 DIAMOND N L,1,3 - -

HORSTMANN CORAL 423 & 424 2,3 1 - -

HORSTMANN 425 DIADEM NL36

HORSTMANN 525 & 527 NL36

HONEYWELL ST669 NL- -

POTTERTON EP2000, EP3000 NL12

RANDALL TSR2P 3 1,2 - -

RANDALL MKII R6 3 1,2 - -

DANFOSS RANDALL 3060 & 3020P 1,7 6 - -

RANDALL 701 NL42

DANFOSS RANDALL SET 2 NL36

SANGAMO M5 410 FORM 4 4,5 3 2 7

SANGAMO S409 FORMS 1 & 4 N,1,3 L - -

SANGAMO (EARLY MODEL) S410 FORM 4 N,2 L - -

SATCHWELL LIBRA 1285

Otros manuales para FP715

Tabla de contenidos

Otros manuales de Controladores de temperatura de Danfoss

Danfoss

Danfoss MBT 5252 Manual de usuario

Danfoss

Danfoss 102 Instrucciones de montaje

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss ECL Comfort 100M Manual de instrucciones

Danfoss

Danfoss 103E7 Instrucciones de montaje

Danfoss

Danfoss 3060 Instrucciones de montaje

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss ECL Comfort L76 Manual de usuario

Danfoss

Danfoss ECL Comfort 310 Manual de usuario

Danfoss

Danfoss Optyma Plus OP-MPS Manual de usuario

Danfoss

Danfoss FHV-A Manual de usuario

Danfoss

Danfoss M150 Manual de usuario

Danfoss

Danfoss RX1 Manual de usuario

Danfoss

Danfoss MBT 400 Manual de usuario

Danfoss

Danfoss FP735Si Manual de usuario

Danfoss

Danfoss ECL Comfort 296 Manual de usuario

Danfoss

Danfoss Optyma AK-RC 204B Manual de usuario

Danfoss

Danfoss EKC 319A Manual de usuario

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss Link RS Manual de usuario

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss EKC 361 Manual de usuario

Danfoss

Danfoss CP715 Si Instrucciones de montaje

Danfoss

Danfoss ECL Comfort P30 Manual de usuario

Manuales populares de Controladores de temperatura de otras marcas

Swegon

Swegon LUNAd MB Manual de usuario

Lucky Reptile

Lucky Reptile Thermo Control II Manual de usuario

SENSORMETRIX

SENSORMETRIX Argon 100 Manual de usuario

Fuji Electric

Fuji Electric PXE4 Manual de usuario

Yuyao gongyi

Yuyao gongyi XMT-808 series Manual de usuario

Selec

Selec TC544C Manual de usuario

P.W. KEY

P.W. KEY rt-208gt Manual de usuario

Future Design

Future Design FDC-9200 Manual de usuario

BH Thermal

BH Thermal BriskONE Manual de usuario

Omron

Omron E5EX-H Manual de usuario

West Control Solutions

West Control Solutions KS 45 Guía de inicio rápido

MCS

MCS RITC-15B Manual de usuario

SMC Networks

SMC Networks Thermo-con INR-244-639 Manual de usuario

eltherm

eltherm Ex-TC It Series Manual de usuario

Omron

Omron C200H-TV Series Manual de usuario

industrie technik

industrie technik CA1 Manual de usuario

KRAL

KRAL EET 32 Manual de usuario

dixell

dixell XR420C Diagrama de cableado