Danfoss CDS 803 Manual de usuario

•

1 Introduction

1.1 Purpose of the Installation Guide

This Installation Guide describes the replacement and the software update for the control card in VLT® Compressor Drive CDS 803.

VLT®is a registered trademark for Danfoss A/S.

1.2 Safety Instructions

Only Danfoss authorized, qualified personnel are allowed to repair this equipment. The personnel must be familiar with the instruc-

tions and safety measures described in the VLT® HVAC Basic Drive FC 101 Service Manual.

WARNING

DISCHARGE TIME

The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be

present even when the warning indicator lights are off.

Failure to wait the specified time after power has been removed before performing service or repair work could result in death or

serious injury.

Stop the motor.

Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and

DC-link connections to other drives.

Wait for the capacitors to discharge fully. The minimum waiting time is specified in the table Discharge time and is also visible

on the nameplate on the top of the drive.

Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors

are fully discharged.

Table 1: Discharge Time

Voltage [V]

Power range [kW (hp)]

Minimum waiting time (minutes)

3x200

6.0–10 (8.0–15)

3x400

6.0–7.5 (8.0–10)

3x400

10–30 (15–40)

1.3 Item Supplied

The following item is supplied:

Control card

Table 2: Code Numbers for Control Cards

Control card type

Code number

Control card, H3, H4, and H5

132B0700

Control card H6

132B1174

Installation Guide

Control Card

VLT® Compressor Drive CDS 803

Danfoss A/S

Ulsnaes 1

DK-6300 Graasten

vlt-drives.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogs, brochures, and other printed material. Danfoss reserves the right to alter its products without notice.

This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already

*130R1211*

*M0032601*

2 Replacing the Control Card

2.1 Disassembly and Replacement

Follow the instructions in the VLT® HVAC Basic Drive FC 101 Service Manual to disassemble the drive and replace the control card.

2.2 Software Compatibility

After repairing or upgrading hardware, it is important to ensure that the entire product runs on the latest released firmware. Down-

load the latest product firmware using VLT® Motion Control Tool MCT 10.

Table 3: Available Firmware Versions

Hardware version

Firmware version

Control card H3, H4, and H5

2.xx(1)(2)

Control card H6

61.xx(1)

1On units produced up until week 33, 2017, fan speed control is not available and the fan runs continuously at full speed.

261.xx update is required for 18.5–22 kW

When downloading the latest firmware, follow the firmware update procedure in the VLT® Motion Control Tool MCT 10 Operating

Guide. MCT 10 can be downloaded from www.danfoss.com in the Service and support/Downloads section.

NOTICE

An internal fault, Alarm 38, occurs if a firmware update is required. Use the normal MCT 10 firmware update to resolve this error.

Replacing the Control Card

Control Card

Installation Guide

Tabla de contenidos

Otros manuales de Accionamiento de CC de Danfoss

Danfoss

Danfoss FC 300 Guía

Danfoss

Danfoss VLT 4000 ME Manual de usuario

Danfoss

Danfoss VLT 8000 AQUA series Manual de usuario

Danfoss

Danfoss VLT Inverter Scroll CDS 801 Manual de usuario

Danfoss

Danfoss VLT AutomationDrive FC 302 Manual de usuario

Danfoss

Danfoss VLT HVAC Basic Drive FC 10 Manual de usuario

Danfoss

Danfoss VLT AQUA Drive FC 200 Manual de usuario

Danfoss

Danfoss VLT AutomationDrive FC 360 Guía del usuario

Danfoss

Danfoss VLT Micro Drive PK18 Guía

Danfoss

Danfoss VLT CDS 803 Guía

Danfoss

Danfoss 176F3167 Guía del usuario

Danfoss

Danfoss VLT series Instrucciones de funcionamiento

Danfoss

Danfoss VLT Midi Drive FC 280 Instrucciones de funcionamiento

Danfoss

Danfoss ADAP-KOOL Drive Instrucciones de funcionamiento

Danfoss

Danfoss VLT Active Front End AFE 302 Manual de usuario

Danfoss

Danfoss VLT AutomationDrive FC 361 Manual de usuario

Danfoss

Danfoss VLT CDS 803 Manual de usuario

Danfoss

Danfoss MCB 113 Manual de usuario

Danfoss

Danfoss VLT AutomationDrive FC 361 Guía

Danfoss

Danfoss AME 435 QM Manual de usuario

Danfoss

Danfoss VLT AQUA Drive FC 202 Instrucciones de funcionamiento

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 100 Series Guía

Danfoss

Danfoss VLT FC 300 Manual de usuario

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador