Danfoss AMI 140 Series Manual de usuario
Data sheet AMI 140
Actuator for two point control
DH-SMT/SI VD.KH.B1.02 © Danfoss 03/2008 1
Description AMI 140 is 2 point 3 wires actuator used with
AB-QM (DN 10-32) and VZ, VZL, VRBZ valves.
The actuator can be used with fan coil units,
induction units, small re-heaters, re-coolers and
zone applications in which hot/cold water is the
controlled medium. The actuator provides with
factory default setting (actuators spindle fully
stem up):
- normally closed function for AB-QM and
- normally open function for VZ, VZL, and VRBZ
Note: it is possible to change setting from normally closed
to normally open function (see “Wiring” part jumper
setting, page 2.
Main data:
• 2-point3wiresversions
• Forceswitch-oatstemdownposition
prevents overload of actuator and valve
• Notoolsrequiredformounting
• Maintenancefreeduringlifetime
• Lownoiseoperation
• Supplied with 1.5 m cable.
Ordering
Type Supply
voltage Speed Code No.
AMI 140 24 V~ 12 s/mm 082H8048
230 V~ 082H8049
Technical data
Power supply 24 Vac, 230 Vac; +10 to –15%
Power consumption 1 VA - 24 Vac; 8 VA - 230 Vac
Frequency 50 Hz / 60 Hz
Close of force 200 N
Stroke 5.5 mm
Speed 12 s/mm
Max. medium temperature inside the pipe 130 °C
Ambient temperature 0 … 55 °C
Storage and transport temperature –40 … +70 °C
Protection code IP 42
Weight 0.3 kg
- marking in accordance with standards
Low Voltage Directive 73/23/EEC, EMC-Directive 2006/95/EEC:
- EN 60730-1, EN 60730-2-14
Spare parts
Type Code No.
Cable (5m) - 24 V 082H8052
Cable (5m) - 230 V 082H8053
Actuator for two point control AMI 140Data sheet
DH-SMT/SI
VD.KH.B1.02 © Danfoss 03/2008
2
Installation Mechanical
The actuator should be mounted with the valve
stem in either horizontal position or pointing
upwards.
The actuator is fixed to the valve body by means
ofamountingringwhichrequiresnotoolsfor
mounting. The ring should be tightened by hand.
Electrical
Important: It is strongly recommended that the
mechanical installation is completed before the
electrical installation.
Each actuator is supplied with the connecting
cable for the controller.
Wiring
AMI 140 - 230VAMI 140 - 24V
Commissioning The factory setting of the spindle is the fully
stem up position because of easier mechanical
connection of the actuator on the valve.
Disposal The actuator must be dismantled and the
elements sorted into various material groups
before disposal.
BLACK
RED
GRAY
Top view
Jumper setting
sw=OFFactuatorretracted
sw=ON actuator extracted sw=OFFactuatorextracted(pushed)
sw=ON actuator retracted (pulled)
default setting for use with ABQM valve
BLUE
BLACK
BROWN
Top view
Jumper setting
sw=OFFactuatorretracted
sw=ON actuator extracted sw=OFFactuatorextracted(pushed)
sw=ON actuator retracted (pulled)
default setting for use with ABQM valve
Common
Black
Bed
Gray
Common
Blue
Black
Brown
Data sheet
DH-SMT/SI VD.KH.B1.02 © Danfoss 03/2008 3
Actuator for two point control AMI 140
a) Check the valve’s neck. The actuator should
be in steam up position (factory setting) .
Ensure that the actuator is mounted securely
on the valve body.
b) Energise the actuator according to the wiring
diagram - see page 2.
c) The direction of stem movement can be
observed on the position indicator .
Installation and
commissioning procedure
(if required)
Manual override
(for service purposes only)
1. Remove the cover.
2. Insert the Allen key 6 into the spindle.
3. Press and hold the button (on the bottom side
of the actuator) during manual override.
4. Pull out the tool.
5. Place cover back on the actuator.
Do not touch anything on
the PCB! Before removing
the cover in need of hand
operation with Allen key
power supply must be
disconnected.
Lethal voltage!
Caution:
Do not manually operate the
drive under power! Remark:
A ”click” sound after energizing the actuator
means that the gear wheel has jumped into
normal position.
position indicator
push
Allen key 6mm
stem up
stem down
4
Actuator for two point control AMI 140Data sheet
VD.KH.B1.02 Produced by Danfoss A/S © 03/2008
Dimensions (mm)
Actuator - valve
combinations
AMI 140 + AMI 140 + AMI 140 + AMI 140 + AMI 140 +
VZ 2, VZL 2 VZ 3, VZL 3 VZ 4, VZL 4 VRBZ AB-QM
Otros manuales para AMI 140 Series
1
Otros manuales de Controladores de Danfoss
Danfoss
Danfoss RAVK Manual de usuario
Danfoss
Danfoss PLUS+1 Series Manual
Danfoss
Danfoss VLT FC 100 Manual de usuario
Danfoss
Danfoss AK-PC 572 Manual de usuario
Danfoss
Danfoss VLT AutomationDrive FC 302 Manual de usuario
Danfoss
Danfoss VLT AutomationDrive FC 302 Manual de usuario
Danfoss
Danfoss PLUS+1 Series Manual
Danfoss
Danfoss 51 Series Manual de usuario
Danfoss
Danfoss vlt aqua Guía
Danfoss
Danfoss ERC 21 Series Manual de usuario
Danfoss
Danfoss AK-PC 560 Manual de usuario
Danfoss
Danfoss VLT 5000 Series Manual de usuario
Danfoss
Danfoss OPTYMA Manual de usuario
Danfoss
Danfoss VLT HVAC Drive FC 102 Instrucciones de funcionamiento
Danfoss
Danfoss AK-PC 420 Manual de usuario
Danfoss
Danfoss AME 655 Manual de usuario
Danfoss
Danfoss 102 Manual de usuario
Danfoss
Danfoss FC 300 Guía
Danfoss
Danfoss ECL Comfort 301 Manual de usuario
Danfoss
Danfoss 4033 Guía
