Danfoss MMIGRS2 Manual de usuario

520H9703

Installation Guide

MCX rooftop controller

Instruction guide

DKRCC.PI.RI0.L1.22 / 520H9703 | 1

DKRCC.PI.RI0.L1.22

520H9703

MCX152V

Ordering no.

080G0304 = 110/230vac

Identication:

Connection:

MCX08M (Optional)

Ordering no.

080G0029 = 110/230vac

MMIGRS2 (Optional)

Ordering no.

080G0294

IP 20

-20 – 60 °C (0 – 140 °F)

RH max. 90% non condensing

CE COMPLIANCE

This product is designed to comply with the following EU standards:

Low voltage guideline: 73/23/EEC Electromagnetic compatibility EMC:

89/336/EEC and with the following norms:

EN61000-6-1, EN61000-6-3 (immunity for residential, commercial and

light-industrial environments)

EN61000-6-2, EN61000-6-4 (immunity and emission standard for

industrial environments)

EN60730 (Automatic electrical controls for household and similar use)

UL APPROVAL

UL ﬁle: E31024

Supply Voltage

85 – 265 V AC, 50/60 Hz

Maximum power consumption: 27 W, 48 VA

Insulation between power supply and the extra-low

voltage: reinforced

Plugs normally not used

Stepper Motor 1, Stepper Motor 2, Stepper Backup,

RS485-2, Digital Input 18

Modbus

It is important that the installation of the data

communication cable be installed correctly.

Remember to terminate each end of the bus.

See separate literature No. RC8AC.

DO - Digital outputs, 15 pcs. DO1 – DO15

DO1 - DO15, all are relays, no solid state relays

The relays are de-rated to the speciﬁed values

AO - Analog output, 6 pcs. AO1 – AO6

Outputs are 0 – 10 V DC by default

AI - Analog Inputs, 14 pcs. AI1 – AI14

All temperature sensors default to PT1000, Pressure

transducers default to 0.5 – 4.5 V DC ratiometric with

5 V DC supply. All other inputs are 0 – 5 V DC by default

DI - Digital switch inputs DI1 – DI17

All Dry contacts except DI17,

(24 V AC or 230 V AC driven)

Technical data:

2 |DKRCC.EI.RL0.I1.02 / 520H9646 © Danfoss | DCS (za) | 2015.08Installation guide | MCX rooftop controller

110 mm - 4.33 in.

280 mm - 11.02 in. 63 mm - 2.48 in.

Dimensions:

Modbus topology:

AK-SM800:

The cable must be EIA485 rated. The cable is connected from controller to controller, and no branches are allowed on the

cable. If the cable length exceeds 1200 m a repeater must be inserted. One repeater must be added for every 32 controllers.

If the data communication cable runs through an electrically noisy environment which impairs the data signal, one or more

repeaters must be added to stabilise the signal.

When conﬁguring Modbus devices on the control bus, the highest device address that can be used is 124

(max 120 modbus control devices in total - max 45 MCX RTC).

The wires are looped from device to device. A is connected to A and B is connected to B. The screen must be connected to the

system device, all controller and any repeaters. A screen must always be looped from device to device.

The screen must not be connected to anything else.

See AK-SM800 User Guide for system 485 wiring instructions.

Manual can be found at: http://food-retail.danfoss.com/knowledge-center/software/ak-sm-800/

Be sure to conﬁgure the Modbus repeater AKA 222 (code#084B2240) to the correct baud rate.

MCX-RTU baud rate must be set to 38.4 K when used with the AK-SM800. MCX-RTU cannot be on the same 485 bus with SLVs.

Termination

Repeater

DKRCC.EI.RL0.I1.02 / 520H9646 | 3© Danfoss | DCS (za) | 2015.08 Installation guide | MCX rooftop controller

Wiring Diagram MCX152V -bottom and top

STEPPER

MOTOR 2

RS485-1

SD/MMC

ST2 4

ST2 3

ST2 2

ST2 1

RS485-2

MEMORY CARD

MCX152V TOP

ANALOG OUTPUT 1-6 ANALOG INPUT 1-7

ANALOG INPUT 8-14

STEPPER

MOTOR 1

ST1 4

ST1 3

ST1 2

ST1 1

AO 6

AO 5

AO 4

COM

AO 3

AO 2

AO 1

COM

15V+

AI 7

AI 6

AI 5

5V+

AI 4

AI 3

AI 2

AI 1

Not used

Damper AO

VS compressors 4

VS compressors 3

Modbus connection

Mixed Air (PT1000)

Outdoor Temp (PT1000)

Fan CT (0 – 5 V DC)

Compr 1 Press (5 V DC)

Compr 2 Press (5 V DC)

Compr 3 Press (5 V DC)

Compr 4 Press (5 V DC)

DP Outside/Mixed Air

Zone CO2(0 – 5 V DC)

Outdoor RH(0 – 5 V DC)

Zone RH(0 – 5 V DC)

Return Air(PT1000)

Supply Air(PT1000)

Zone Temp(PT1000)

COM

15V+

AI 14

AI 13

AI 12

5V+

AI 11

AI 10

AI 9

AI 8

COM 1

D1 +

D1 -

COM 2

D2 +

D2 -

VS compressors 2

VS compressors 1

Fan AO

Contact info:

www.danfoss.com

Installation guide | MCX rooftop controller DKRCC.EI.RL0.I1.02 / 520H9646 | 4

DIGITAL INPUT 18 DIGITAL OUTPUT 9-12 DIGITAL OUTPUT 13-15

STEPPER BACKUP DIGITAL INPUT 1-8 DIGITAL INPUT 9-16

POWER

SUPPLY

MCX152V BOTTOM

CANCAN-RJ ETHERNET DIGITAL INPUT 17

COM

CANL

CANH

R120

COM 17

DI 17

DIGITAL OUTPUT 6-8

NO 8

C 8

NO 7

C 7

NO 6

C 6

DIGITAL OUTPUT 1-5

NO 3

C 3

NO 2

C 2

NO 5

C 5

NO 4

C 4

NO 1

C 1

CAN-RJ

ETH

DI 17H

Input Voltage

110 – 230 V AC

Optional IO Expansion

Optional - Remote Display

Not Used

Cool 4 Proof

Aux Heat 4 (N.O.)

Aux Heat 3 (N.O.)

Aux Heat 2 (N.O.)

Aux Heat 1 (N.O.)

Cool 4 (N.O.)

Cool 3 (N.O.)

Cool 2 (N.O.)

Cool 1 (N.O.)

Stepper Backup

NOT USED

Fan Proof

Phase Loss

Shutdown 1

Shutdown 2

Fan Drive Fault

Compr 1 Drive Fault

Compr 2 Drive Fault

Compr 3 Drive Fault

Compr 4 Drive Fault

Filter Clogged Fault

Damper Override

Title 24

Schedule Override

Cool 1 Proof

Cool 2 Proof

Cool 3 Proof

Reheat (N.O.)

Damper (N.O.)

Heat Reclaim 1 (N.O.)

Heat Pump (N.O.)

Fan Low Speed (N.O.)

Fan High Speed (N.C.)

COM

+ BATT

15V+

COM

DI 9

DI 10

DI 11

DI 12

COM

DI 13

DI 14

DI 15

DI 16

COM

DI 1

DI 2

DI 3

DI 4

COM

DI 5

DI 6

DI 7

DI 8

DI 18H

DI 18

COM 18

C 9

NO 9

C 10

NO 10

C 11

NO 11

C 12

NO 12

C 13

NO 13

NC 13

C 14

NO 14

NC 14

C 15

NO 15

NC 15

Wiring Diagram MCX152V -bottom and top

Otros manuales para MMIGRS2

Este manual sirve para los siguientes modelos

Otros manuales de Controladores de Danfoss

Danfoss

Danfoss ACI 30-1 Manual de usuario

Danfoss

Danfoss EKC 201 Manual de usuario

Danfoss

Danfoss WP75- RF Instrucciones de montaje

Danfoss

Danfoss ERC 213 Manual de usuario

Danfoss

Danfoss VLT 6000 series Manual de usuario

Danfoss

Danfoss MCO 305 Guía

Danfoss

Danfoss EKC 202C-MS Manual de usuario

Danfoss

Danfoss AME 435 QM Manual de usuario

Danfoss

Danfoss AME 445 Manual de usuario

Danfoss

Danfoss PLUS+1 MC0XX-1 series Manual

Danfoss

Danfoss AMV 610 Manual de usuario

Danfoss

Danfoss VT2800 Series Guía

Danfoss

Danfoss ADAP-KOOL AK-PC 651 Manual de usuario

Danfoss

Danfoss EET Series Manual de usuario

Danfoss

Danfoss ADAP-KOOL Drive Manual de usuario

Danfoss

Danfoss AK-PC 530 Manual de usuario

Danfoss

Danfoss AK-PC 351 Manual de usuario

Danfoss

Danfoss AK-CH 650 Manual de usuario

Danfoss

Danfoss AME 55 Manual de usuario

Danfoss

Danfoss DMS 300 Manual de usuario

Danfoss

Danfoss VLT MCD 200 Manual de usuario

Danfoss

Danfoss ECL Comfort 100M Manual de usuario

Danfoss

Danfoss OBC 80 Series Manual de usuario

Danfoss

Danfoss AMV 150 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario