Danfoss VLT MCD 200 Manual de usuario

MCD USB Module Instructions Introduction

MI.17.C1.02 – VLT®is a registered Danfoss trademark 1

INSTALLATION INSTRUCTIONS: MCD USB MODULE

1. Introduction

The USB Module can be used in conjunction with WinMaster to manage Danfoss soft starters.

These instructions detail the installation, set-up and configuration of the USB Module. For details on

using WinMaster, refer to the WinMaster help file.

2. Installation

CAUTION

Remove mains and control voltage from the soft starter before attaching or removing accessories.

Failure to do so may damage the equipment.

MCD 200

Plug the module onto the side of the soft starter.

MCD 500:

To plug the module onto the side of the soft starter, line

the interface up with the comms port slot.

Press the top retaining clip of the module into the soft

starter chassis first, then press in the bottom retaining

clip.

177 HA58 5.10

Remove the module using the following procedure:

1. Remove control power and mains supply from the soft

starter.

2. Take the module off-line.

3. Disconnect the USB cable from the module.

4. Push a small flat-bladed screwdriver into the slots at the top

and bottom of the module and depress the retaining clips.

5. Pull the module away from the soft starter.

177HA378.10

Connection MCD USB Module Instructions

MI.17.C1.02 - VLT®is a registered Danfoss trademark 2

3. Connection MCD 200 MCD 500

MCD 200 MCD 500 (Remote mode)

USB Module 17, 18: Stop input

USB port 25, 18: Reset input

USB Module

USB port

For the USB Module to accept serial commands, a link must be fitted across terminals A1-N2 on MCD

200 starters.

Input links are required across terminals 17 and 25 to18 if the MCD 500 soft starter is being operated

in Remote mode. In Local mode, links are not required.

N.B.!:

MCD 500 parameter 3-2 selects whether the soft starter will accept Start and Stop

commands from the Serial Network Master while in Remote Mode. See the soft starter

user manual for parameter details.

MCD USB Module Instructions Configuration

MI.17.C1.02 – VLT®is a registered Danfoss trademark 3

4. Configuration

To bring the USB Module on-line:

1. Remove control power and mains supply from the soft starter.

2. Attach the module to the soft starter as illustrated.

3. Connect the module to the PC via a USB cable. The PC should detect the module and the

Hardware Update Wizard will open.

4. Install the supplied USB UART driver to operate the module as follows.

The driver can be found in the USB Comms Drivers folder on the supplied CD. Click on the Browse

button then navigate to the drivers folder and select the appropriate folder for your operating

system.

Click on Ok, then Next. The software will install. If you see a prompt, click Continue Anyway. Once

installation is complete, click Finish.

5. The PC will prompt you to install serial port driver software. Repeat the procedure in

Step 4. You may need to restart your PC once the driver software is installed.

Configuration MCD USB Module Instructions

MI.17.C1.02 - VLT®is a registered Danfoss trademark 4

6. Identify the USB Serial Port assignment by checking Control panel > System > Hardware >

Device Manager> Ports (COM & LPT).

N.B.!:

If the USB port is not shown, disconnect then reconnect the cable. If the problem

persists, restart your PC.

7. Open WinMaster and change the Network Settings to:

Protocol: AP Binary or AP ASCII

Baud rate: 9600

Serial Port: Use the serial port number identified above

8. Apply control voltage to the soft starter. Bring WinMaster on-line, then Search for Network

Starters.

N.B.!:

The starter may trip on Starter Comms while the Master is off-line. Reset the soft starter

and place the Master on-line.

N.B.!:

The drivers will configure the USB port that the module is connected to. You must use

the same physical USB port every time you connect the module to the PC.

MCD USB Module Instructions Specifications

MI.17.C1.02 – VLT®is a registered Danfoss trademark 5

5. Specifications

Order code

...................................................................................................................... 175G9009

Enclosure

Dimensions ............................................................. 35 mm (W) x 157 mm (H) x 90 mm (D)

Weight ...................................................................................................................... 250 g

Protection ................................................................................................................... IP20

Mounting

Spring-action plastic mounting clips (x 2)

Connections

Soft starter ........................................................................................... 6-way pin assembly

Network ................................................................................................................... USB-B

Maximum cable length ..................................................................... 3 metres (not supplied)

Settings

Protocol

MCD 200 ....................................................................................................... AP ASCII

MCD 500 ........................................................................................................... Binary

Address .......................................................................................................................... 20

Data rate (bps) ........................................................................................................... 9600

6. Troubleshooting

Symptom Cause and solution

“Unknown Device has been

detected” message when interface

is first plugged in

The USB cable may be too long.

Use a standard USB cable less than 3 metres long.

WinMaster goes offline and soft

starter trips on Starter Comms The USB cable has been unplugged.

Ensure the cable is plugged in at both ends, then bring

WinMaster back on-line.

WinMaster locks up when on-line.

Log view indicates comms failure

and a change to offline mode

Severe external electrical disturbance or equipment

failure.

Reconnect the USB cable, the close and restart

WinMaster. Bring WinMaster on-line.

If the problem persists, contact your local supplier.

Otros manuales para VLT MCD 200

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Danfoss

Danfoss

Danfoss PVG 128 Manual de usuario

Danfoss

Danfoss 088U0200 Manual de usuario

Danfoss

Danfoss EV220BW 15-50 Manual de usuario

Danfoss

Danfoss ICF 15 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss AMZ 112 Manual de usuario

Danfoss

Danfoss ICLX 100 Manual de usuario

Danfoss

Danfoss AK-CC 550A Manual de instrucciones

Danfoss

Danfoss BVTS Manual de usuario

Danfoss

Danfoss TWA-Z Gen. 2011 Manual de usuario

Danfoss

Danfoss Icon Master Guía del usuario

Danfoss

Danfoss POV Series Manual de usuario

Danfoss

Danfoss ICF 15 Manual de usuario

Danfoss

Danfoss PVG 16 PVH/Covers Manual

Danfoss

Danfoss MCO 101 Manual de usuario

Danfoss

Danfoss PVG-EX 32 Manual

Danfoss

Danfoss GPS 40-150 Manual de usuario

Danfoss

Danfoss AB-QM series Manual de usuario

Danfoss

Danfoss ASV-PV Manual de usuario

Danfoss

Danfoss SVA-S 15-200 Series Manual de usuario

Danfoss

Danfoss PVG 32 Manual

Danfoss

Danfoss PVG 120 Manual

Danfoss

Danfoss PVG 100 Manual

Danfoss

Danfoss AFQM Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario