Danfoss 088U0200 Manual de usuario

088U0200 / 088U0205

Instruction CF-MC Master Controller

Instruktion CF-MC Hauptregler

Vejledning CF-MC Masterregulator

Instruction Régulateur principal CF-MC

Bruksanvisning CF-MC Master Controller

Instruction CF-MC Master Controller

VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Instruktion . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Vejledning . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Bruksanvisning .........................44

Instruction CF-MC Master Controller

2VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-MC Master Controller

VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

1. Introduction ................................................................................................ 4

2. CF2 System Overview ................................................................................ 4

3. Functional Overview.................................................................................. 4

4. Mounting ..................................................................................................... 5

4.1 Wall ......................................................................................................................... 5

4.2 DIN-Rail ................................................................................................................. 5

5. Installation Procedure (Sequential) ........................................................ 5

5.1 24V Actuators...................................................................................................... 5

5.2 Relays for Pump & Boiler Control................................................................. 5

5.3 Input for Global Standby ................................................................................ 6

5.4 Input for Heating & Cooling........................................................................... 6

5.5 Wiring..................................................................................................................... 6

5.6 Power Supply...................................................................................................... 6

5.7 External Antenna (CF-EA) .............................................................................. 7

5.8 More (2-3) Master Controllers ....................................................................... 7

5.9 Other System Components ........................................................................... 7

5.10 Transmission Test (Link Test) ....................................................................... 8

6. Conguration.............................................................................................. 8

6.1 Actuator Outputs............................................................................................... 8

6.2 Relays for Pump & Boiler Control................................................................. 9

6.3 Input for Global Standby and Heating & Cooling.................................. 9

6.4 Relays on more (2-3) Master Controllers................................................... 10

7. Replacing / Resetting the Master Controller ........................................ 11

7.1 When?.................................................................................................................... 11

7.2. How? .................................................................................................................... 11

8. Specications.............................................................................................. 12

9. Troubleshooting ......................................................................................... 12

10. Figures and illustrations ......................................................................... A-B

Index

Instruction CF-MC Master Controller

4VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

• The Master Controller, CF-MC, is a part of the new trend-setting CF2 wire-

less hydronic oor heating control system from Danfoss. Based on 2-way

wireless communication technology CF2 oers high transmission safety,

easy wireless installation, a high level of individual room temperature

control, and thus optimal comfort and improved energy eciency.

• The system has a variety of benecial features and easily accessed applica-

tion functionalities. This includes a Master Controller, CF-MC, with short-

circuit protected outputs, regulation by ON/OFF or Pulse Width Modula-

tion (PWM) principles, global standby, separate relays for both pump

and boiler control, self-diagnostic program and error indication, wireless

transmission (link) test possibility on each type of Room Thermostat, easy

wireless system access and extended functionality via the optional Remote

Controller, and Repeater Unit for extended wireless range.

a) Master Controller, CF-MC

b) Room Thermostats, CF-RS, -RP, -RD and -RF

c) Remote Controller, CF-RC

d) Repeater Unit, CF-RU

e) External Antenna, CF-EA

1. Introduction

2. CF2 System Overview - g. 1

3. Functional Overview - g. 2

Menu selection button

Menu LEDs

Output and conguration selection button

OK button

Output LEDs

Output cable xing

Relays for pump and boiler

Input for heating/cooling (external ON/OFF switch)

Input for global standby (8°C) (external ON/OFF switch)

Power supply (230V)

Front cover release

External antenna connection

Instruction CF-MC Master Controller

VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

4. Mounting

4.1 Wall

•Remove the front cover (g. 3)

•Mount with screws and wall plugs (g. 4)

4.2 DIN-Rail

•Mount DIN-rail parts (g. 5)

•Click on DIN-rail (g. 6)

•Release from DIN-rail (g. 7)

Note: The Master Controller should be mounted in an horizontal upright position

5. Installation Procedure (Sequential)

Important Note: Complete all the installations on the Master Controller

described below before connecting to a 230V power supply !

5.1 24V Actuators

•Connect the two actuator wires to an output (g. 8)

•Fix the cable

Round cable (g. 9)

Squared/at cable (g. 10)

Note: If NC (normally closed) actuators are installed for ON/OFF regulation, no

further actuator output conguration is needed (see 6.1) !

5.2 Relays for Pump & Boiler Control

•Pump: Connect the live wire (L) across the Pump Relay from an external

power supply. Make sure the power supply is switched o. Then connect

the live wire, and complete other connections to the pump in accordance

with existing law. (g. 11)

•Fix the cable (g. 12)

•Boiler: Connect the live wire (L) across the Boiler Relay from an external

power supply. Make sure the power supply is switched o. Then connect

the live wire, and complete other connections to the boiler in accordance

with existing law.

Note: The relays for pump and boiler are potential free contacts and can thus

NOT be used as direct power supply. Max. load is 230V and 8A / 2A (inductive) !

Instruction CF-MC Master Controller

6VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

5.3 Input for Global Standby

•Connect the two wires from an external switch (ON/OFF) to the two termi-

nals for the Global Standby input. (g. 13)

When this switch is closed (ON) the system will override the current set

point for all the room thermostats and change it to 8°C

•Fix the cable. (g. 14)

Note: The Global Standby ensures a set room temperature xed at 8°C for all

Room Thermostats, but it can be changed with the Remote Controller, CF-RC.

5.4 Input for Heating & Cooling

•Connect the two wires from an external switch (ON/OFF) to the two termi-

nals for the heating and cooling input. (g. 15)

When this switch is closed (ON) the system will switch from heating to

cooling mode.

•Fix the cable. (g. 16)

Note #1: When the system is in cooling mode the actuator output will be acti-

vated (ON when NC actuators / OFF when NO actuators) when the temperature

in a room exceeds the set point.

Note #2: When the system is in cooling mode an independent dew-point alarm

function should be installed.

Danfoss oers the below listed components (see example g. 17)

EDA-24V: Electronic dew-point alarm - 088H3001

EDA-S: Dew-point sensor - 088H3011

TWA-A: 24V-NO actuator – 088H3111

RA-C 20: Danfoss cooling valve* - 013G3096

•This valve must be dimensioned according to the placement on the

primary side if the application structure in the example is chosen!

5.5 Wiring

5.6 Power Supply

•When all actuators, pump and boiler controls and other inputs are in-

stalled, connect the Master Controller’s power supply plug to a 230V

power supply. (g. 18)

Note: If the power supply plug is removed from the power supply cable dur-

ing installation make sure that the connection is made according to existing

law/legislation.

LNLN

91087654321

Actuator outputsRelays

Input

Global Standby

Heating/Cooling

External

Antenna

Instruction CF-MC Master Controller

VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

5.7 External Antenna (CF-EA)

Note: The External Antenna is installed as diverter when there is NO transmis-

sion possible through a large building, heavy construction or metal barrier, e.g.

if the Master Controller is located in a metal cabinet/box

•Remove the plastic cover from the antenna connection on the Master

Controller. (g. 19)

•Connect the External Antenna. (g. 20)

•Place the External Antenna on the other side of the transmission barrier

away from the Master Controller.

5.8 More (2-3) Master Controllers

Notes: Master Controller #1 should be the one connected to the local supplying

pump.

Up to 3 Master Controllers can be connected in one system.

If there are 2 or 3 Master Controllers, connect them to a 230V power sup-

ply within a distance from Master Controller #1 that allows simultaneous

handling of all the Master Controllers

Activate Install mode on Master Controller #1(g. 21)

• Use the menu selection button to select the Install mode. Install LED

ashes

• Activate Install mode by pressing OK . Install LED goes ON

Initiate installation on Master Controller #2 or #3(g. 22)

• Activate installation to Master Controller #1 by pressing OK

• Install LED and ickers during communication

and goes OFF when installation is complete

• Relocate Master Controller #2 and/or #3 if necessary. Link test will be

initiated automatically on reconnection to 230V power supply

• If Master Controller #2 and/or #3 has it’s own pump, the relays for pump

and boiler must be congured accordingly (see 6.4)

Note: Later removal of Master Controller #2 or #3 from Master Controller #1 can

only be done by resetting Master Controller #1 (see 7.2)

5.9 Other System Components

Note: The Installation procedure of other system components to the Master

Controller (Room Thermostats, Remote Controller, and Repeater Unit ; see 2.) is

described in the enclosed instructions for these system components. Please see

these instructions for specic installation procedures

Instruction CF-MC Master Controller

8VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

5.10 Transmission Test (Link Test)

Note: The transmission test (link test) between the Master Controller and other

system components, is initiated from the other system components like Room

Thermostats, Repeater Unit, Remote Controller, etc.

Please see the enclosed instruction for these components for transmission test

(link test) procedures.

Room Thermostats:

When the transmission test (link test) from a Room Thermostat is received

by the Master Controller, the assigned output(s) will ash. This makes it pos-

sible to identify the outputs to which a Room Thermostat has been assigned

(Fig. 23 - )

6. Conguration

6.1 Actuator Outputs

Activate Output mode on Master Controller (g. 23)

• Use the menu selection button to select the Output mode. Output LED

ashes

• Activate Output mode by pressing OK . Output LED goes ON

Select the output conguration

• Press the output selection button and toggle between the possible out-

put congurations - the output LEDs will be ON – indicated below:

• 1 LED: The outputs are congured to NC actuators with ON/OFF regulation

(default)

• 2 LEDs: The outputs are congured to NO actuators with ON/OFF regula-

tion

• 3 LEDs: The outputs are congured to NC actuators with Pulse Width

Modulation (PWM) regulation for oor heating

• 4 LEDs: The outputs are congured to NO actuators with Pulse Width

Modulation (PWM) regulation for oor heating

• 5 LEDs: A Remote Controller is installed, and it is not possible to change

settings from the Master Controller

• Activate selected output conguration by pressing OK

Note: During periods with no output activations the Master Controller will run a

valve motion program every 2 weeks and it will last for up to 12

minutes. Individual output conguration is possible with Remote Controller,

CF-RC, see separate instruction.

Instruction CF-MC Master Controller

VI.UH.K2.80 Produced by Danfoss Floor Heating Hydronics 01.2006

6.2 Relays for Pump & Boiler Control

Activate Relay mode on Master Controller (g. 23)

• Use the menu selection button to select the Relay mode. Relay LED

ashes

• Activate Relay mode by pressing OK . Relay LED goes ON

Select the Relay conguration

• Press the output selection button and toggle between the possible

Relay congurations - the output LEDs will be ON – indicated below:

• NO LEDs: The relays are not used

• 1 LED: Pump control

• 2 LEDs: Boiler control

• 3 LEDs: Pump and boiler control

• 4 LEDs: Pump control with 2min. start/stop delay

• 5 LEDs: Pump and boiler control, with 2min. start/stop delay on pump

(default)

• Activate selected relay conguration by pressing OK

Note: If the pump relay is active, the Master Controller will run a pump motion

program every 3rd day and it will last for one minute.

6.3 Input for Global Standby and Heating & Cooling

Activate Input mode on Master Controller (g. 23)

• Use the menu selection button to select the Input mode. Input LED

ashes

• Activate Input mode by pressing OK . Input LED goes ON

Select the Input conguration

• Press the output selection button and toggle between the possible

Input congurations - the output LEDs will be ON – indicated below:

• 1 LED: The input ports are not used

• 2 LEDs: The Master Controller will switch to cooling mode when the input

for heating/cooling is activated (g. 2 - )

• 3 LEDs: The Master Controller will switch to a xed set room temperature

at 8 °C for all Room Thermostats when the input for global standby is

activated (g. 2 - )

• 4 LEDs: The Master Controller will switch to cooling mode when the input

for heating/cooling is activated (g. 2 - ). In heating mode the Master

Controller will switch to a xed set room temperature at 8 °C for all Room

Thermostats when the input for global standby is activated (g. 2 - )

(default)

• Activate selected input conguration by pressing OK

Otros manuales para 088U0200

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de control de Danfoss

Danfoss

Danfoss MSV-F2 DN15 - 400 Manual de usuario

Danfoss

Danfoss iC7 Series Manual de usuario

Danfoss

Danfoss 103E5 Instrucciones de montaje

Danfoss

Danfoss EV210B Instrucciones de funcionamiento

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss 176F3417 Manual de usuario

Danfoss

Danfoss Colibri ETS 12C Manual de usuario

Danfoss

Danfoss ICM Instrucciones de funcionamiento

Danfoss

Danfoss RLV Manual de usuario

Danfoss

Danfoss TEA 20 Manual de usuario

Danfoss

Danfoss FH-WC Manual de usuario

Danfoss

Danfoss VHX-DUO Manual de instrucciones de instalación

Danfoss

Danfoss AK-CC 550A Manual de instrucciones

Danfoss

Danfoss PVG 120 Manual de usuario

Danfoss

Danfoss KP 1 Manual de usuario

Danfoss

Danfoss ICLX 32 Manual de usuario

Danfoss

Danfoss RA2000 Manual de usuario

Danfoss

Danfoss PM3 Instrucciones de funcionamiento y mantenimiento

Danfoss

Danfoss ETS 250 Manual de usuario

Danfoss

Danfoss SVA-S SS 15 Manual de usuario

Danfoss

Danfoss VF3 DN 200 Manual de usuario

Danfoss

Danfoss GPS 40-150 Manual de usuario

Danfoss

Danfoss ICM 20 Manual de usuario

Danfoss

Danfoss AMV 110 NL AQT Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario