Danfoss Link SCM Manual de usuario

MAKING MODERN LIVING POSSIBLE

Danfoss Heating Solutions

Danfoss Link™ SCM

Simple Communication Module

Installation Guide

2VIFZT102 © Danfoss 03/2013

Installation Guide Danfoss Link™ SCM

Introduction .................................................. 5

Installation ................................................... 5

Mounting..................................................... 5

Wiring ........................................................ 6

Adding the device ............................................ 6

Perform network test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Transmission test (optional) ................................... 7

Factory reset.................................................. 7

Status indicator ............................................... 7

Getting started with Danfoss Link™ SCM ....................... 8

Technical specications ....................................... 9

Disposal instructions .......................................... 9

Table of Contents

VIFZT102 © Danfoss 03/2013

Installation Guide Danfoss Link™ SCM

The Danfoss Link™ SCM (Simple Communication Module) is an

electronic controller for turning the Away function ON/OFF in a

Danfoss Link™system.

The Danfoss Link™ SCM is powered by 230 V~.

Introduction

Installation

The Danfoss Link™ wireless system’s transmission range is suf-

cient for most applications; however each building has dierent

obstacles aecting communication and maximum transmission

distance.

If communication problems occur Danfoss suggests to support

the system with repeaters. In exceptional cases the wireless

system may not be suitable for your installation.

Note: Be aware that installation and placement must be according

to local building regulations.

Mounting

4VIFZT102 © Danfoss 03/2013

Installation Guide Danfoss Link™ SCM

Wiring

The process of adding the Danfoss Link™ SCM

to a system is performed on the Danfoss

Link™ CC.

Note that the Danfoss Link™ SCM

must be added as a Service

Device.

When adding, press and

release the install button,

and observe that the LED

gives a fast green ash.

If adding is successful the LED turns green (HOME) or red (AWAY)

permanently - depending on input stage.

For further information, see the Danfoss Link™ CC installation

guide.

Note: If adding the Danfoss Link™ SCM to the Danfoss Link™ CC is

unsuccessful, make sure the right Danfoss Link™ CC software

version is applied. Correct version: 2.5.57 or higher.

Adding the device

PWR+

COM

PWR-

Note: Refer to the Danfoss Link™ Mobile Phone Butler (Danfoss

Link™ MPB) manual for wiring connections to the Danfoss

Link™ MPB.

Black (+)Black/white (-)

VIFZT102 © Danfoss 03/2013

Installation Guide Danfoss Link™ SCM

Green LED ON Away OFF

Red LED ON Away ON

Green LED fast ash Adding or link test

Green LED short ash Ready for adding

Red LED slow ash

for 5 seconds Adding not OK

Red LED slow ash

continously

Transmission test not OK or lost

connection to Danfoss Link™ CC

Status indicator

Turn o the power to the device, then press and hold the install

button in front of the device for approx. 5 seconds while the

power is switched on again. The button must be held until LED

gives a red ash.

Factory reset

Once the Danfoss Link™ SCM and all other

devices in the system have been registered

and the Danfoss Link™ CC is placed in its nal

position, perform a full network test (see

separate Danfoss Link™ CC manual).

Perform network test

Transmission test (optional)

Initiate a transmission test on the Danfoss Link™ SCM by pressing

and holding the install button for more than 2 seconds. If the test

is satisfactory the green LED will ash and a message is displayed

on the Danfoss Link™ CC. If the test fails the red LED will slow

ash continuously.

6VIFZT102 © Danfoss 03/2013

Installation Guide Danfoss Link™ SCM

The away temperature can only be set on the Danfoss Link™ CC,

default setting is 15° C.

A SIM-card for the Danfoss Link™ Mobile Phone Butler is not

included. Before inserting the SIM-card please remember to dis-

able the PIN-code.

System test

After installation it is recommended to perform a

system test by texting (0000#0) to the Danfoss Link™

MPB in order to set the Danfoss Link™system to AWAY

mode (OFF).

On the Danfoss Link™ MPB and the SCM the AWAY mode is

indicated by a red LED. On the Danfoss Link™ CC the AWAY mode

is indicated by the suitcase icon.

After 10 minutes the AWAY mode screen will be replaced by the

Standby screen for security reasons.

Send another text message (0000#1) to revert the system to

the HOME mode (ON). The LED turns green and the AWAY icon

disappears. See the Danfoss Link™ MPB User Manual for further

information.

Smartphone app

For Android phones and iPhones you can download the Danfoss

ButlerApp for easy communication with the Danfoss Link™ MPB.

Other ON / OFF devices like sensors, manual switches, etc.

can also be used and connected to the SCM for turning

AWAY mode ON / OFF in the Danfoss Link™ system. The

ON / OFF device must be connected to the SCM via its NC and

COM slots.

Getting started with Danfoss Link™ SCM

VIFZT102 © Danfoss 03/2013

Installation Guide Danfoss Link™ SCM

Technical specications

Operating voltage Danfoss Link™ SCM 8 - 32 VDC

Operating voltage (Net adapter) 220 - 240 V~, 50 Hz

Standby consumption 0.9 W

Ambient temperature 0˚ to +45˚C

Transmission frequency 868.42 MHz

Transmission range in normal

buildings Up to 30 m

Transmission power Max. 1 mW

Pollution degree 2

Ball pressure test temperature 75˚C

Software classication Class A

IP class 20

Dimensions 80 × 80 × 30 mm

Disposal instructions

013R9559 VIFZT15X © Danfoss 01/2013

Danfoss A/S

Heating Solutions

Haarupvaenget 11

8600 Silkeborg

Denmark

Phone: +45 7488 8000

Fax: +45 7488 8100

Email: heating.solutions@danfoss.com

www.heating.danfoss.com

Tabla de contenidos

Otros manuales de Unidad de control de Danfoss

Danfoss

Danfoss AB-QM DN 125 Manual de usuario

Danfoss

Danfoss AKD 5001 Manual de usuario

Danfoss

Danfoss MCO 101 Manual de usuario

Danfoss

Danfoss BVTS Manual de usuario

Danfoss

Danfoss VLT 380-500 V Guía

Danfoss

Danfoss MBC 5000 Manual de usuario

Danfoss

Danfoss 103E5 Instrucciones de montaje

Danfoss

Danfoss EV251B Manual de instrucciones de instalación

Danfoss

Danfoss AVTB Manual de usuario

Danfoss

Danfoss PVG 16 Manual de usuario

Danfoss

Danfoss VLT Ea4 Manual de usuario

Danfoss

Danfoss AK-CM 102 Manual de usuario

Danfoss

Danfoss SVA-S Manual de usuario

Danfoss

Danfoss VCM 46 Manual de usuario

Danfoss

Danfoss PVG 32 Manual de usuario

Danfoss

Danfoss DSV 10 Manual de usuario

Danfoss

Danfoss TWA-Z Gen. 2011 Manual de usuario

Danfoss

Danfoss VF3 DN 200 Manual de usuario

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario

Danfoss

Danfoss DHP-R 7UA HPC EM Manual de usuario

Danfoss

Danfoss 1000 Hz Control Card MK-I Manual de usuario

Danfoss

Danfoss TGE 10 Manual de usuario

Danfoss

Danfoss ASV-PV series Manual de usuario

Danfoss

Danfoss XGE-4C Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario