Danfoss DHP-R 7UA HPC EM Manual de usuario

VMILF102

DHPR&DP

INSTALLATION INSTRUCTIONS

EXPANSION MODULE, HPC EM

COOLING MODULE, HPC CM

VMILF1022 – Danfoss

VMBQI102

VMILF102 Danfoss – 3

Table of contents

Installation for WCS function (warm water loading) ... 4

Installation for TWC function (tap water control)...... 6

Installation for Shunt function ....................... 8

Important information!

24 VAC 1 must not be connected together with:

󰥎

 •24VAC2

 •24VDC

 •Otherequipmentthatuses0-10Vcontrolsignal

 •SignalgroundGND

24 VAC 2 must only be used as power supply to:

󰥎

 •Externalequipmentthatrequires0-10Vcontrolsignal

 •Auxiliarymodules

The two separate 24 VAC circuits must never be connected

󰥎 to each other or to protective ground.

The total power load on 24 VAC 1 respectively 24 VAC 2 must

󰥎 notexceed50VA.

VMILF1024 – Danfoss

VMBQI102

Expansion module, HPC EM

Theoperationaldescriptionfortheexpansionmoduleisavailableinthecontrollermanual.

Installation for WCS function (warm water loading)

Application

TheexpansionmoduleinWCSoperationalmodecontrolswarmwaterloadingofthe

water heaters.

WCS operation is achieved by setting the switch according to the ﬁgure.

Required accessories for installation

Submersiblesensor,Thermokon-DanelkoAKF1004140,itemno.086U3364

One of the following modular cables:

Modularcable0.3m,itemno.086U4227

Modularcable1.1m,itemno.086U4228

Modularcable10.0m,itemno.086U4229

Connectionblock,itemno.086U5121

Other accessories

PilotvalveVVL(2-way),heatexchanger(tapwatervvx),circulationpump.

System image

Heat exchanger

Aheatexchangerisconnectedbetweentheheatpumpandthecirculationforthewaterheatersasdepictedinthesystem

image above.

Circulation pump

Acirculationpumpisconnectedneartheheatexchanger.

Pilot valve

Apilotvalveisconnectedbetweenthecirculationpumpandtheheatexchanger.

Submersible sensor

Asubmersiblesensorisconnectedonthereturnlineoftheheatexchanger,asclosetotheheatexchangeraspossible.

Heat circuit

Hot gas circuit

Cooling agent circuit

VVB VVB VVB VVB

Heatexchanger

Modular cable

Steering valve

Circulation pump

Expansion module

WCS operation

Submersible sensor

return VVX

VVC

DHP-R Eco

VMBQI102

VMILF102 Danfoss–5

Connecting

󰥎 Note!Themaximumloadmaynotexceed50VA.

Expansion module

Theexpansionmoduleismountedintheelectriccabinetontheintendedrail.Ifthereisnoroom,themodulecanbeinstal-

ledinanexternal,enclosedcabinetandconnectedwithalongermodularcable.

• SettheswitchesonthefrontoftheexpansionmoduletotheWCSposition



• ConnectamodularcablebetweenHPCRMExp.outandHPCEMExp.in

Connections of expansion module for WCS operation:

Temperatureinput,T1:Submersiblesensor(heatexchangerreturnline)

Temperatureinput,T2:-

Analogueoutput0-10V,AO1:Signaltopilotvalve

Relay,DO1:Signaltocirculationpump(no-potentialclosure,maximum6A)

Exp.in:ConnectionfromHPCRM

Exp.out:Connectiontopossibleadditionalmodule.

Submersible sensor



• ConnecttoT1andGND

Circulation pump



• ConnecttoDO1.1to24VAC2.1



• ConnectDO1.2tothecontactorcoil(therelaycoil)andfurtherto24VAC2.2

Pilot valve



• ConnectAO1tothesignalinputofthepilotvalve



• ConnectGNDtopilotvalveGND.IfGNDismissinginthepilotvalve,connectGNDto24VAC2.2somewhereinthe

system. It is most appropriate to jumper terminals 144 and 146 in the controller cabinet.



• ConnectthepilotvalveterminalGto24VAC2.1



• ConnectthepilotvalveterminalG0to24VAC2.2.

•

Exp.in

GGNDG0Y1

Exp.out

DO1.1

AO1

GND

DO1.2

HPC EM

WCS

24 VAC 2.1

24 VAC 2.2

alt. GG

0Y1

24 VAC 2.1

24 VAC 2.2

AO1

0-10V

Circ. pump

FromExp.out

Submersible sensor

Pilot valve

VMILF1026 – Danfoss

VMBQI102

Installation for TWC function (tap water control)

Application

In the TWC mode, the expansion module ensures that outgoing hot tap wa- ter

and heat water circulation have a suﬃciently high temperature, to prevent the pre-

sence of Legionella bacteria.

TWC operation is achieved by setting the switch according to the ﬁgure.

Required accessories

2 PT1000 strap-on temperature detectors with 2 m of cable, item no.

086U3365(itemnumbercorrespondsto1transmitter)

One of the following modular cables:

Modularcable0.3m,itemno.086U4227

Modularcable1.1m,itemno.086U4228

Modularcable10.0m,itemno.086U4229

Connectionblock,itemno.086U5121

System image

Sensor, water heater

Astrap-ontemperaturedetectorisconnectedonthesupplylineleadoftheendheater,beforethemixingvalve.

Sensor, hot water return

Astrap-ontemperaturedetectoris connectedonthereturnleadofthewarmwatercirculation,beforethecirculation

pump.

Heat circuit

Hot gas circuit

Cooling agent circuit

VVB VVB VVB VVB

Modular cable

Sensor, water heater

Electriccartridge

Sensor, hot water return

Expansion module

TWC function

VVC

DHP-R Eco

VMBQI102

VMILF102 Danfoss–7

Connecting

󰥎 Note!Themaximumloadmaynotexceed50VA.

Expansion module

Theexpansionmoduleismountedintheelectriccabinetontheintendedrail.Ifthereisnoroom,themodulecanbeinstal-

ledinanexternal,enclosedcabinetandconnectedwithalongermodularcable.

• SettheswitchesonthefrontoftheexpansionmoduletotheTWCposition



• ConnectamodularcablebetweenHPCRMExp.outandHPCEMExp.in

Connections of expansion module for TWC operation:

Temperature input, T1: Sensor, water heater

Temperature input, T2: Transmitter, hot water return

Analogueoutput0-10V,AO1:-

Relay,DO1:Signaltoelectriccartridge,hotwater(no-potentialclosure,maximum6A)

Exp.in:ConnectionfromHPCRM

Exp.out:Connectiontopossibleadditionalmodule.

Electric cartridge



• ConnecttoDO1.1to24VAC2.1.



• ConnectDO1.2tothecontactorcoil(therelaycoil)andfurtherto24VAC2.2.

Sensor, water heater



• ConnectthesensorcabletoT1andGND.

Sensor, hot water return



• ConnectthesensorcabletoT2andGND.

Exp.in

Exp.out

DO1.1

AO1

GND

DO1.2

HPC EM

TWC

24 VAC 2.1 24 VAC 2.2

Start signal for

electric cartridge

water heater

Hot water return

FromExp.out

VMILF1028 – Danfoss

VMBQI102

Installation for Shunt operation

Application

Intheshuntmode,theexpansionmodulemaintainstherequiredtemperaturefora

second heat circuit.

The shunt function is achieved by setting the switch according to the ﬁgure.

Required accessories

1PT1000strap-ontemperaturedetector,itemno.086U3365

One of the following modular cables:

Modularcable0.3m,itemno.086U4227

Modularcable1.1m,itemno.086U4228

Modularcable10.0m,itemno.086U4229

Connectionblock,itemno.086U5121

Other accessories

Shunt valve, circulation pump.

System image

Sensor, shunt temperature

Astrap-ontemperaturedetectorisconnectedonthesupplylineoftheheatcircuit,afterthecirculationpump.

Heat circuit 1

Heat circuit 2

Hot gas circuit

Cooling agent circuit

VVB VVB VVB VVB

Shunt valve

Sensor, shunt temperature

Circulation pump

Modular cable

Expansion module

Shunt function

VVC

DHP-R Eco

VMBQI102

VMILF102 Danfoss–9

Connecting

󰥎 Note!Themaximumloadmaynotexceed50VA.

Expansion module

Theexpansionmoduleismountedintheelectriccabinetontheintendedrail.Ifthereisnoroom,themodulecanbeinstal-

ledinanexternal,enclosedcabinetandconnectedwithalongermodularcable.

• SettheswitchesonthefrontoftheexpansionmoduletotheShuntposition.



• ConnectamodularcablebetweenHPCRMExp.outandHPCEMExp.in

Connections of expansion module for shunt operation:

Temperature input, T1: Sensor, shunt temperature.

Temperatureinput,T2:-

Analogueoutput0-10V,AO1:Signaltoshuntvalve.

Relay,DO1:Signaltocirculationpump(no-potentialclosure,maximum6A).

Exp.in:ConnectionfromHPCRM.

Exp.out:Connectiontopossibleadditionalmodule.

Sensor, shunt temperature



• ConnecttoT1andGND

Circulation pump



• ConnecttoDO1.1to24VAC2.1.



• ConnectDO1.2tothecontactorcoil(therelaycoil)andfurtherto24VAC2.2.

Shunt valve



• ConnectAO1tothesignalinputofthepilotvalve.



• ConnectGNDtopilotvalveGND.IfGNDismissinginthepilotvalve,connectGNDto24VAC2.2somewhereinthe

system. It is most appropriate to jumper terminals 144 and 146 in the controller cabinet.



• ConnectthepilotvalveterminalGto24VAC2.1.



• ConnectthepilotvalveterminalG0to24VAC2.2.

Exp.in

GGNDG0Y1

Exp.out

DO1.1

AO1

GND

DO1.2

HPC EM

Shunt

24 VAC 2.1

24 VAC 2.2

0-10V

alt.

0Y1

24 VAC 2.1

24 VAC 2.2

AO1

Circ. pump

FromExp.out

Shunt temperature

Shunt valve

VMILF10210 – Danfoss

VMBQI102

Inputs and outputs, HPC EM

Temperature inputs

Input Shunt TWC WCS

T1 Shunt temperature HW heater temp WCS temperature

T2 – HW return temp –

Analogue outputs

Outputs Shunt TWC WCS

AO1 Control signal – Control signal

Relay outputs

Outputs Shunt TWC WCS

DO1 Circulation pump Heater HW Circulation pump

Otros manuales de Unidad de control de Danfoss

Danfoss

Danfoss Genesis Passive Manual de usuario

Danfoss

Danfoss SCA-X Manual de usuario

Danfoss

Danfoss DSV 1 Manual de usuario

Danfoss

Danfoss SVA-S 6-10 Manual de usuario

Danfoss

Danfoss DSV 10 Manual de usuario

Danfoss

Danfoss CHV-X 15-125 Manual de usuario

Danfoss

Danfoss PVG 120 Manual de usuario

Danfoss

Danfoss AB-QM Series Manual de usuario

Danfoss

Danfoss MCO 101 Manual de usuario

Danfoss

Danfoss AME 13 SU Manual de usuario

Danfoss

Danfoss GBCH Series Manual de usuario

Danfoss

Danfoss VACON NXP IP00 Manual de usuario

Danfoss

Danfoss AME 13 Manual de usuario

Danfoss

Danfoss XGE-4C Manual de usuario

Danfoss

Danfoss RT 110 Manual de usuario

Danfoss

Danfoss PVG-EX 32 Manual

Danfoss

Danfoss AMZ 112 Manual de usuario

Danfoss

Danfoss OPTYMA Manual de instrucciones

Danfoss

Danfoss MSV-F2 DN Series Manual de usuario

Danfoss

Danfoss iC7 Series Manual de usuario

Danfoss

Danfoss ICF 15 Manual de usuario

Danfoss

Danfoss OSPE Manual de usuario

Danfoss

Danfoss RA2000 Manual de usuario

Danfoss

Danfoss SVA-DH Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario