Dahua Technology IPC-HDW5231R-Z Manual de usuario

Dahua HD IR Bullet Network Camera Quick Start Guide

Version 1.0.0

Dahua Vision Technology Co. LTD

Welcome

Thank you for purchasing our Network camera!

This user’s manual is designed to be a reference tool for your system.

Please read the following safeguard and warnings carefully before you use this series product!

Please keep this user’s manual well for future reference!

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

Please check if the power supply is correct before operating the device.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is rated DC 12V or AC 24V in the IEC60950-1. (Power supply requirement is

subject to the device label).

Please install easy-to-use device for power off before installing wiring, which is for emergent power

off when necessary.

Please prevent the line cord from being trampled or pressed, especially the plug, power socket and

the junction from the device.

Note: Do not connect these two power supplying sources to the device at the same time; it

may result in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper

handling or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Environment

Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus; otherwise

it may cause overexposure (It is not the device malfunction), which will affect the longevity of CCD

or CMOS.

Please transport, use and store the device within the range of allowed humidity and temperature.

Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and

with strong electromagnetic radiation or unstable lighting.

Please do not allow water and other liquid falling into the camera in case that the internal

components are damaged.

Please do not allow rain or damp to the indoor device in case fire or lightning may occur.

Please keep the sound ventilation in case of heat accumulation.

Please pack the device with standard factory packaging or material with same quality when

transporting the device.

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3. Operation and Daily Maintenance

Please do not touch the heat dissipation component of the device directly in order to avoid scald.

Please do not dismantle the device; there is no component which can be fixed by users themselves

in the machine. It may cause water leakage or bad image for the device due to unprofessional

dismantling. Please contact after-sale service to replace desiccant if it becomes green.

It is recommended to use the device with thunder proof device in order to improve thunder proof

effect.

The grounding holes of the product are recommended to be grounded to further enhance the

reliability of the camera.

Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust

or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if

it is necessary to clean.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean

the device. Don’t use volatile solvent like alcohol, benzene, thinner and etc or strong detergent with

abrasiveness, otherwise it will damage the surface coating or reduce the working performance of

the device.

Dome cover is an optical device, please don’t touch or wipe cover surface directly during

installation and use, please refer to the following methods to deal with once dirt is found:

Stained with dirt

Use oil-free soft brush or hair dries to remove it gently.

Stained with grease or fingerprint

Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or

paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change

the cloth and wipe several times if it is not clean enough.

Warning

Please modify the default password after login in order to avoid being stolen.

Please use the standard accessories provided by manufacturer and make sure the device is

installed and fixed by professional engineers.

Please prevent the device surface from the radiation of laser beam when using laser beam device.

Please do not provide two or more power supply modes for the device, otherwise it may cause

damage to the device.

Statement

Please refer to the actual product for more details; the manual is just for reference.

The manual will be regularly upgraded according to the product update; the upgraded content will

be added in the manual without prior announcement.

Please contact the supplier or customer service if there is any problem occurred when using the

device.

iii

Please contact the customer service for the latest procedure and supplementary documentation.

There may be deviation between the actual value of some data and the value provided in the

manual due to the reasons such as the real environment is not stable and so on. Please refer to

the company’s final explanation if there is any doubt or dispute.

The company is not liable for any loss caused by the operation which is not followed by the manual.

FCC Information

1. FCC conditions：

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference;

This device must accept any interference received, including interference that may cause

undesired operation.

2. FCC compliance：

This equipment has been tested and found to comply with the limits for a digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio

communication. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Note:

Please refer to the disk for more details, check and download corresponding user’s manual and tool.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Installation Accessories Bag

Table of Contents

1Device Structure .........................................................................................................................1

1.1 Device External Cable .................................................................................................1

1.2 Framework and Dimension.........................................................................................2

1.3 Alarm Setup...................................................................................................................2

2Device Installation ......................................................................................................................5

3Network Configuration...............................................................................................................9

3.1 Modify IP Address........................................................................................................9

3.2 Login WEB Interface..................................................................................................10

1Device Structure

1.1 Device External Cable

Note:

The following figure is for reference only, which is used to know the function of cable port.

There are differences about cable structure between different models, please refer to the actual

product for more details.

You can refer to the following figure for cable information. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

No.

Port

Name

Function

Connector

Note

AUDIO

OUT

Audio

output port

RCA

Output audio signal to speaker and etc.

AUDIO

Audio input

port

RCA

Input audio signal, receive analog audio signal from

pick up and etc.

LAN

Network

port

Ethernet

port

Connect to standard Ethernet cable.

Note: Some series don’t support PoE.

I/O

I/O port

Alarm signal input/output.

Power

Power input

port

Power port. Input DC 12V or AC 24V power.

Note:

Please connect the DC5.5 round port to 2-pin

converter cable when you are using AC 24V power.

Please use according to device tag.

Please refer to the follow sheet for detailed pin information.

Port Name

Name

Note

I/O Port

ALARM_NO

Alarm output port. It is to output the alarm signal to the

alarm device.

NO: normal open alarm output port.

It must be used with ALARM_COM.

ALARM_COM

Alarm output public port.

ALARM_IN1

Alarm input port 1. It is to receive the on-off signal from

the external alarm source.

ALARM_IN2

Alarm input port 2. It is to receive the on-off signal from

the external alarm source.

GND

Ground port

1.2 Framework and Dimension

Note:

The following figure is for reference only, which is used to know the device dimension.

Please refer to the following figure for dimension information. The unit is mm. See Figure 1- 2.

Figure 1-2

1.3 Alarm Setup

Note:

It is only supported by some series products.

Figure 1-3

Alarm input, output description:

Step 1

Connect alarm input device to the alarm input of I/O port cable.

Step 2

Connect alarm output device to the ALARM_OUT and ALARM_OUT_GND of I/O port cable,

Alarm output is the relay switch output; alarm output port can only be connected to NO (normally

open) alarm device.

Step 3

Open the WEB, set alarm input and output correspondingly in alarm setup. Alarm input on the

WEB is corresponding to that of the device I/O port cable. When there is alarm, alarm input

device will generate signal of high and low level. Set corresponding NO and NC inputs.

Step 4

Set alarm output on the WEB, the alarm output is corresponding to the alarm output end of the

device, this is the alarm output port of the I/O port cable.

Please refer to the following figure for alarm input and output information. See Figure 1-4.

Alarm input: When the input signal is idle or grounded, the device can collect the different

statuses of the alarm input port. The input signal is connected to 3.3V or is idle; the device

collects the logic “1”. When the input signal is grounded, the device collects the logic “0”.

Figure 1-4

Please refer to the following figure for alarm output information. See Figure 1-5 and Figure 1-6.

Figure 1-5

Figure 1-6

Mode A:

Level application. Alarm output high and low level, alarm output is OC; it needs to increase pull-

up resistance externally to work normally. Max external pull-up level is 5V, max port current is

5mA. After external pull-up resistance is increased, the default of output signal is high level

(external pull-up voltage), and it switches to low level when there is alarm output (when the

working current is 5mA, output voltage is less than 0.8V).

Mode B:

Switch application. Alarm output is used to drive external circuit, max current is 30mA, max

voltage is 5V, it is advised to add a relay if it is beyond the value.

2Device Installation

Important

Please make sure the installation surface can min support the 3X weight of the camera

and the bracket.

Figure 2-1

Please see Figure 2-1.

Step 1

SD card installation (Optional)

You can see the SD installation card slot, analog output, two direction button and reset

button after you open the lower cover.

Insert the SD card into the slot which is shown in Figure 2-2, you can press the SD card

slightly to insert it because the card slot is elastic.

Figure 2-2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Dahua Technology

Dahua Technology

Dahua Technology HD IR Mini Bullet Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW81230E-Z Manual de usuario

Dahua Technology

Dahua Technology HAC-HDBW2401RP-Z Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-PDW3849-A180-AS-PV-ANZ Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW2531T-ZS-S2 Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW2241T-S-0280B Manual de usuario

Dahua Technology

Dahua Technology WizMind IPC-PDBW82041-B360 Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-PFW8601N-H-A180 Manual de usuario

Dahua Technology

Dahua Technology 59230UNI Manual de usuario

Dahua Technology

Dahua Technology A42AR2 Manual de usuario

Dahua Technology

Dahua Technology HFW5241E-ZE Manual de usuario

Dahua Technology

Dahua Technology N43AJ52 Manual de usuario

Dahua Technology

Dahua Technology D-SDZ4032-HNR-ZB Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HFW11A0SN-W Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HDBW3541FP-AS-M-0280B Manual de usuario

Dahua Technology

Dahua Technology Eyeball Manual de usuario

Dahua Technology

Dahua Technology EOL Series Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW1230S1-0280B-S5 Manual de usuario

Dahua Technology

Dahua Technology A21BC0V Manual de usuario

Dahua Technology

Dahua Technology D-IPC-HUM8441-E1-L1 Manual de usuario

Dahua Technology

Dahua Technology DH-HAC-HUM1220GN-B Manual de usuario

Dahua Technology

Dahua Technology IPC-HUM4431S-L4 Manual de usuario

Dahua Technology

Dahua Technology N52BF5Z Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HDW1230T1P-S4 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario