D-Link DES-1250G Manual de usuario

Before Your Begin

This Quick Installation Guide gives step-by-step instructions for setting up the D-Link

DES-1250G Web-Smart Switch. The model you have purchased may appear slightly

different from those shown in the illustrations. For more detailed information about the

switch, its components, making network connections, and technical specifications,

please refer to the User’s Manual on the master CD included with your switch.

Check Your Package Contents

These are the items included with your DES-1250G purchase:

(on the top include the rubber feet, rackmount kit as part of package contents) If any of the above

items are missing, please contact your reseller.

holders. Software and specifications subject to change without notice.

• DES-1250G

D-Link Web Smart 48-Port 10/100Mbps+2-

Port combo 10/100/1000Mbps Copper/Mini-

GBIC Gigabit Ethernet Switch

• CD-ROM (containing Manual and Utility

Installation)

• 100–240VAC 50/60Hz

Power Adapter

Using a powe

supply with a

different voltage rating

will damage and void

the warranty for this

product.

DES-1250G

Web Smart48-Port

10/100Mbps+2-Port combo

10/100/1000Mbps Copper/Mini

GBIC Gigabit Ethernet Switch

Setup The DES-1250G Switch

The setup of the Switch can be performed using the following steps:

A. Install the DES-1250G in a fairly cool and dry place. See the

Technical Specifications for the acceptable operation temperature

and humidity ranges.

B. Install the DES-1250G in a site free from strong electromagnetic

field generators (such as motors), vibration, dust, and direct

exposure to sunlight.

C. Leave at least 10cm (about 4 inches) of space at the front and rear

of the hub for ventilation.

D. Visually inspect the DC power jack and make sure that it is fully

secured to the power adapter.

E. Install the DES-1250G on a sturdy, level surface that can support

its weight, or in an EIA standard-size equipment rack.

F. When installing the Switch on a level surface, attach the rubber feet

to the bottom of each device. The rubber feet cushion the hub and

protect the hub case from scratching.

Attach the adhesive rubber pads to the bottom

Rack Mounting

The DES-1250G can be mounted in an EIA standard-size, 19-inch rack,

which can be placed in a wiring closet with other equipment. Attach the

mounting brackets to both sides of the Switch (one at each side), and

secure them with the provided screws.

Use the screws provided. Then, use screws provided with the

equipment rack to mount the Switch in the rack.

Mount the Switch in the rack

Connecting Network Cable

The DES-1250G supports 2 ports of 10/100/1000Mbps Gigabit

Ethernet. It runs full-/half- duplex transfer mode for 10/100Mbps and

full-duplex transfer mode for 1000Mbps. Each port on the DES-

1250G supports Auto-MDI/MDI-X. Auto-MDI/MDI-X is a feature that

eliminates the need for worrying about using either a standard or

crossover cable—you can use either one—and allows any port to be

an uplink port.

AC Power

The DES-1250G can be used with AC power supply 100~240V AC,

50~60Hz. The power switch is located at the rear of the unit adjacent to

the AC power connector and the system fan. The switch’s power supply

will adjust to the local power source automatically and may be turned on

without having any or all LAN segment cables connected.

Connect The DES-1250G Gigabit

Switch To Your Network

Front Panel

LED Indicators Mini GBIC Ports

┌―――――――――――――――――――――――――――┐┌―┐

└―――――――――――――――――――――――――――┘└―┘

10/100 Base-TX 1000 Base-T

Twisted-Pair Ports Twisted Pair Ports

 10/100BASE-TX Twisted-Pair Ports (Port1~48)

These ports support network speeds of either 10Mbps or 100Mbps,

and can operate in half- and full- duplex transfer modes. These ports

also support automatic MDI/MDI-X crossover detection, giving true

“plug and play” capability. Just plug the network cable directly into the

hub; you can use either straight-through or crossover cable.

 1000BASE-T Twisted Pair Ports (Port 49~50)

The DES-1250G is equipped with two Gigabit twisted pair ports that

are auto negotiable 10/100/1000Mbps and also support auto

MDI/MDIX crossover detection. These two ports can operate in half-

and full- duplex modes.

 Mini-GBIC Ports (Option Port 49~50)

The Switch is equipped with two mini-GBIC ports, supported optional

1000BASE-SX/LX mini-GBIC module.

Note: When the port is set to “Forced Mode”, Auto MDI/MDIX will

be disabled.

LED Indicators

LED stands for Light-Emitting Diode.

The front panel LEDs provide instant status feedback and simplify

monitoring and troubleshooting tasks.

LED indicators of the Switch

 Power LEDs

On When the Power LED light is on, the Switch is

receiving power.

Off When the Power LED light is off, the power cord is

improperly connected.

CPU LEDs ( Management Indicator)

Blinking When the CPU is working, the System LED is

blinking.

On/Off The CPU is not working.

 Ports 1-48 Status LEDs

Link/Act:

On When the LED light is on, the respective port is

connected to the 10/100Mbps Ethernet network.

Blinking When the LED light is blinking, the port is

transmitting or receiving data on the 10/100Mbps

Ethernet network.

Off There is no link.

 Ports 49 & 50 Status LEDs

Link/Act:

On : When the Link/ACT LEDA lights on, the

respective port is successfully connected to an

Ethernet network.

Blinking : When the Link/ACT LED is blinking, the port is

transmitting or receiving data on the Ethernet

network.

Off : There is no link.

Speed:

(Green)

: When the green light is on, the respective port is

connected to a 1000Mbps Gigabit Ethernet

network.

(Amber)

When the Amber light is on, the respective port is

connected to a 100Mbps Fast Ethernet network.

Off : When the respective port is connected to a

10Mbps Ethernet or No link

 Option Ports 47~48 mini-GBIC Status LEDs

Link/Act

On : When the mini-GBIC module is installed and

connected to a network, the Link/ACT LED lights on.

Blinking : When the LED is blinking, the mini-GBIC module is

receiving data on a network.

Off : There is no link.

Installing the Web Management

Utility

Through the Web browser you can configure switch functions such as

VLAN, Trunking, QoS… etc.

The following instruction guides you to install the Web Management

utility.

1. Insert the Utility CD in the CD-ROM Drive.

2. From the Start menu on the Windows desktop, choose Run.

3. In the Run dialog box, type D:\Web Management Utility\setup.exe

(D:\ depends where your CD-ROM drive is located) and click OK.

4. Follow the on-screen instructions to install the utility.

5. Upon completion, go to Program Files ->

web_management_utility and execute the Web Management

utility. (Figure 1.)

Figure 1. Web Management Utility

Configuring the Switch

The DES-1250G has a Web GUI interface for smart switch

configuration. The Switch can be configured through the Web browser.

A network administrator can manage, control and monitor the switch

from the local LAN. This section indicates how to configure the Switch

to enable its smart functions.

Use Internet Explorer 5.0 or above Web browser.

Before you configure this device, note that when the Web Smart Switch

is configured through an Ethernet connection, make sure the manager

PC must be set on the same IP network. For example, when the default

network address of the default IP address of the Web Smart Switch is

192.168.0.1, then the manager PC should be set at 192.168.0.x (where x

is a number between 2 and 254), and the default subnet mask is

255.255.255.0.

Enter IP address http://192.168.0.1 (the factory-default IP address

setting) to the address location. (Figure 2.)

Figure 2.

Or through the Web Management Utility, you do not need to remember

the IP Address, Select the device shown in the Monitor List of the Web

Management Utility to settle the device on the Web browser.

When the following dialog page appears, remain enter the default

password "admin" and press Login to enter the main configuration

window. (Figure 3.)

Figure 3.

After entering the password, the main page appears and the screen will

display the device status. (Figure 4.)

Figure 4.

Setup Menu

When the main page appears, find the Setup menu on the left side of

the screen (Figure 5). Click on the setup item that you want to configure.

There are eleven options: Port Settings, VLAN Settings, Trunk Setting,

Mirror Setting, Device Status, System Settings, Trap Setting, Password

Setting, Backup Setting, and Reset Setting as shown in the Main Menu

screen.

Figure 5.

Technical Support

You can find software updates and user documentation on the D-Link website.

D-Link provides free technical support for customers within the United States

and within Canada for the duration of the warranty period on this product.

U.S. and Canadian customers can contact D-Link technical support through our

website, or by phone.

Tech Support for customers within the United States:

D-Link Technical Support over the Telephone:

(877) 453-5465

Monday to Friday 6:00AM to 6:00PM PST

D-Link Technical Support over the Internet:

http://support.dlink.com

email:[email protected]

Tech Support for customers within Canada:

D-Link Technical Support over the Telephone:

(800) 361-5265

Monday to Friday 8:30am to 9:00pm EST

Saturday adn Sunday 11:00am to 7:00pm EST

D-Link Technical Support over the Internet:

http://support.dlink.ca

email:[email protected]

Tech Support for customers within

the United Kingdom & Ireland:

D-Link UK & Ireland Technical Support over the Telephone:

+44 (0)20 7365 8440 (United Kingdom)

+353 (0)12 421 061 (Ireland)

Monday to Friday 8:00 am to 10:00 pm

D-Link Technical Support over the Internet:

http://www.dlink.co.uk

Otros manuales para DES-1250G

Tabla de contenidos

Otros manuales de Enrutador de red de D-Link

D-Link

D-Link DIR-845L Manual de usuario

D-Link

D-Link DSL-G804V Manual de usuario

D-Link

D-Link xStack DES-3200 Series Manual de usuario

D-Link

D-Link DIR-806A Manual de usuario

D-Link

D-Link DES-1005 Manual de usuario

D-Link

D-Link DIR-455 Manual de usuario

D-Link

D-Link G413K Manual de usuario

D-Link

D-Link DSL-526B Manual de usuario

D-Link

D-Link DES-3010F Manual de usuario

D-Link

D-Link DIR-815/AC Manual de usuario

D-Link

D-Link Express Ethernetwork DI-707P Manual de usuario

D-Link

D-Link DSL-2600U Manual de usuario

D-Link

D-Link GO-SW-5E Manual de usuario

D-Link

D-Link IR850LA1 Manual de usuario

D-Link

D-Link DIR-857 Manual de usuario

D-Link

D-Link DSL-2543B Manual de usuario

D-Link

D-Link DSL-2500U Manual de usuario

D-Link

D-Link DIR-868L Manual de usuario

D-Link

D-Link DIR-600L Manual de usuario

D-Link

D-Link DIR-815 Manual de usuario

D-Link

D-Link DIR-300NRU Manual de usuario

D-Link

D-Link DIR-140L Manual de usuario

D-Link

D-Link DSL-G804V Manual del propietario

D-Link

D-Link xStack DGS-3400 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad