Cypress CH-1507TX Manual de usuario

CH-1507TX & CH-1507RX

HDMI to CAT5e/6/7 Transmitter and Receiver with

LAN/IR/RS-232/PoE

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

VR0 21/10/13 Prelimiary Release

VS1 09/12/13 Updated Text/Diagrams

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 1

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Transmitter Front and Rear Panels ..3

6.2 Receiver Front and Rear Panels......4

6.3. IR Cable Pin Assignment .................5

6.4. D-Sub 9-Pin Denitions .....................5

7. Connection Diagram ............................ 6

8. Specications ........................................ 7

8.1 Technical Specications ..................7

8.2 CAT5e/6/7 Cable Specication ......8

9. Acronyms ............................................... 8

1. INTRODUCTION

The CH-1507 Transmitter and Receiver set can send uncompressed

audio/video and IP data over a single run of CAT5e/6/7 cable at

a distance of up to 100 meters. It has the added benet of control

through the built-in RS-232 and IR ports and a bi-directional LAN

serving connection. The receiver (PD) can be powered by the PoE

(48V) function of the transmitter (PSE), allowing for greater exibility in

installations

2. APPLICATIONS

• 48V PoE (Power over Ethernet) from Transmitter (PSE) to Receiver (PD)

• Household entertainment sharing and control

• Lecture room display and control

• Showroom display and control

• Meeting room presentation and control

• Classroom display and control

3. PACKAGE CONTENTS

• 1×HDMI to CAT5e/6/7 (with LAN/IR/RS-232) Transmitter

• 1×CAT5e/6/7 to HDMI (with LAN/IR/RS-232) Receiver

• 1×IR Blaster

• 1×IR Extender

• 1×48 V/0.83 A DC Power Adaptor

• Operation Manual

4. SYSTEM REQUIREMENTS

HDMI source equipment such as a DVD/Blu-ray player and HDMI

equipped output display (TV or monitor).

5. FEATURES

• HDMI with 3D, 4K×2K support, HDCP and DVI compliant

• Simultaneous transmission of uncompressed data over a single

CAT5e/6/7 cable up to 100m/328ft

• HDBaseT™ 5PlayT™ convergence: uncompressed high denition Video

and Audio, LAN serving, Power over Ethernet and RS-232/IR control

• Uncompressed video support up to 1080p@60 Hz/36-bit

• High denition audio support up to LPCM 7.1CH, Dolby TrueHD,

Dolby Digital Plus and DTS-HD Master Audio

• Supports audio sampling rates of 32 kHz to 192 kHz

• Supports standard 48V power from Transmitter (PSE) to Receiver (PD)

• Supports CEC bypass

• Installation friendly

Note:

1. This system was tested with CAT5e/6/7 cables, results may vary

with cables of a different specication.

2. The standard 48V PoE function is designed for powering

compatible Receiver units only—non-PoE Receivers will need

their own power supply. Receivers from other brands may not be

compatible.

3. For playback of 4K×2K HDMI source signals, a 4K×2K capable

display and High Speed HDMI cables are required.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Transmitter Front and Rear Panels

RearFront

RS-232 In

LAN

HDMI In

HDMI to CAT5e/6/7 with LAN/IR/RS232

Transmitter

CAT5e/6/7 Out

Link

IR2 Extender

IR1 Blaster

DC 48V

Power

2 31 64 7 8 95

HDMI IN: Connect to HDMI source equipment such as a DVD or

Blu-ray player.

LAN: Connect to an active network for LAN serving. This allows

network access (including internet access if available) to

be shared to any device (e.g. a smart TV or games console)

connected to the LAN port of the receiver

Warning: DO NOT connect the LAN connection to the CAT5e/6/7

output, doing so may trigger a power shut down and may damage

the device.

RS-232 IN: Connect to a PC or laptop with D-Sub 9-pin male cable

for the transmission of RS-232 commands.

POWER LED: This blue LED will illuminate when the device is

connected to a power supply.

DC 48V: Connect the 48 V DC power supply to the transmitter and

Plug the adaptor into an AC outlet.

IR 1 BLASTER: Connect an IR Blaster cable for IR signal transmission.

IR signals received by an IR extender connected to the receiver

unit will be transmitted by this blaster. Place the IR Blaster in direct

line-of-sight of the equipment to be controlled.

IR2 EXTENDER: Connect an IR Extender cable for IR signal reception.

Signals received will be transmitted from any IR blaster connected

to the receiver unit. Ensure that the remote being used is within the

direct line-of-sight of the IR Extender.

LINK LED: The yellow LED will illuminate when both the source

connected to the transmitter and the display connected to the

receiver are connected. The LED will blink regularly to indicate

that no signal is being received from the display and irregularly to

indicate that an error has occurred.

CAT5e/6/7 OUT: Connect to the receiver unit with a single

CAT5e/6/7 cable for transmission of all data signals.

6.2 Receiver Front and Rear Panels

RS-232 Out

LAN

HDMI Out

CAT5e/6/7 to HDMI with LAN/IR/RS232

Receiver

RearFront

CAT5e/6/7 In

Link

IR1 Extender

IR2 Blaster

Power

2 31 65 7 84

HDMI OUT: Connect to a HDMI equipped TV/monitor for display of

the HDMI input source signal.

LAN: Connect to a LAN equipped device (such as a smart TV or

games console) to share the network access (including internet

access if available).

Warning: DO NOT connect the LAN connection to the CAT5e/6/7

output, doing so may trigger a power shut down and may damage

the device.

RS-232 OUT: Connect to the device that is to be controlled (via

D-Sub 9-pin female cable) by RS-232 commands.

POWER LED: This blue LED will illuminate when the device is

connected to a power supply.

IR2 BLASTER: Connect an IR Blaster cable for IR signal transmission.

IR signals received by an IR extender connected to the transmitter

unit will be transmitted by this blaster. Place the IR Blaster in direct

line-of-sight of the equipment to be controlled.

IR1 EXTENDER: Connect an IR Extender cable for IR signal reception.

Signals received will be transmitted from any IR blaster connected

to the tranmitter unit. Ensure that the remote being used is within

the direct line-of-sight of the IR Extender.

LINK LED: The yellow LED will illuminate when both the source

connected to the transmitter and the display connected to the

receiver are connected. The LED will blink regularly to indicate

that no signal is being received from the display and irregularly to

indicate that an error has occurred.

CAT5e/6/7 IN: Connect to the transmitter unit with a single

CAT5e/6/7 cable for transmission of all data signals.

6.3. IR Cable Pin Assignment

Power 3.3V

IR Blaster Signal

IR Signal

Power 3.3 V

Ground

IR Extender

IR Blaster

6.4. D-Sub 9-Pin Denitions

PIN DEFINE TX / RX

1N/C

2TxD / RxD

3RxD / TxD

4N/C

5GND

6N/C

7N/C

8N/C

9N/C

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Cypress

Cypress

Cypress CSC-5300 Manual de usuario

Cypress

Cypress CPLUS-V4H1HP Manual de usuario

Cypress

Cypress CHDD-41AR Manual de usuario

Cypress

Cypress CHDMI-81 Manual de usuario

Cypress

Cypress CLUX-81 Manual de usuario

Cypress

Cypress CLUX-22HC Manual de usuario

Cypress

Cypress CPRO-3D42S Manual de usuario

Cypress

Cypress CDVI-41 Manual de usuario

Cypress

Cypress CHDMI-41AT Manual de usuario

Cypress

Cypress CLUX-C41C Manual de usuario

Cypress

Cypress DVT-17 Manual de usuario

Cypress

Cypress CHDMI-31 Manual de usuario

Cypress

Cypress HX3 CY4609 Manual de usuario

Cypress

Cypress CLUX-41SY Manual de usuario

Cypress

Cypress CPRO-3D41GAME Manual de usuario

Cypress

Cypress CHDMI-41 Manual de usuario

Cypress

Cypress CLUX-42S Manual de usuario

Cypress

Cypress CHDD-3C Manual de usuario

Cypress

Cypress CLUX-61 Manual de usuario

Cypress

Cypress CLUX-21SY Manual de usuario

Cypress

Cypress CHDMI-81 Manual de usuario

Cypress

Cypress CLUX-41AT Manual de usuario

Cypress

Cypress CLUX-C41 Manual de usuario

Cypress

Cypress CHMX-24 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario