CYP CDPS-84HB Manual de usuario
CDPS-84HB
8 by 4 Digital Presentation Scaler
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2012 by Cypress Technology.
All Rights Reserved.
Version 1.0 October 2009
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 05/05/14 Preliminary Release
RDV2 09/15/14 Add RS-232 Commands
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 Remote Control ...............................5
6.4 IR Pin Assignment .............................6
6.5 RS-232 Pin Assignment .....................7
6.6 RS-232/Telnet Commands...............8
6.7 OSD Menu.......................................11
7. Connection Diagram .......................... 15
8. Specications ...................................... 16
8.1 Input Resolution Support ...............17
8.2 Output Resolution Support ...........18
9. Acronyms ............................................. 19
1
1. INTRODUCTION
This HDBaseT™ capable 8 by 4 Digital Presentation Scaler can switch
and scale HDMI/HDBaseT/PC/Composite Video signals from any one
of its eight inputs and simultaneously display it on any of its HMDI or
HDBaseT outputs. The unit has and HDMI bypass output, allowing local
monitoring of any of the HDMI or HDBaseT inputs, and features full
5play™ convergence for easy integration of compatible transmitters
and receivers. It has the added benet of control via IR remote
control, RS-232, IP/Telnet and WebGUI, with all information including
system status presented on its comprehensive LCD display.
2. APPLICATIONS
• Home Theater/Entertainment
• Lecture Room/Hall Presentation
• Show Room/Demo Room
• Public Commercial Display
• Information Board
3. PACKAGE CONTENTS
• 1 x 8 by 4 Presentation Scaler
• 1 x IR Extender Cable
• 1 x IR Receiver Cable
• 1 x Remote Control with Battery
• 1 x 24V/ 2.7A DC Power Adaptor
• 1 x Power Cord
• Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as Blu-ray/DVD/PS3 player or Set-Top-Box
and output HDMI TV/Display and or audio amplier with connection
cables.
2
5. FEATURES
• HDMI, HDCP and DVI compliant
• Full 5Play™ convergence: Video, Audio, LAN serving, Power over
Cable (PoC) and Control (IR & RS-232 bypass)
• Supports distances of up to 100 meters over industry standard
CAT5e/6/7 cable
• Supports scaling of any input signals to a wide range of HDTV and
PC output resolutions up to 1080p and WUXGA (RB)
• Digital to Analog and Analog to Digital Audio conversion (DAC/
ADC)
• Simultaneous video output of the selected source through the
HDBaseT and HDMI outputs and audio output through the digital
coaxial and analog L/R outputs
• Features four HDMI inputs with corresponding L/R audio inputs
(3.5mm mini-jack), two HDBaseT CAT5e/6/7 inputs, PC (15-pin D-Sub)
with L/R audio (3.5mm mini-jack) and Composite Video and L/R
audio (3 RCA)
• Features two HDMI outputs, one HDBaseT CAT5e/67 outputs, one
Digital Coaxial audio output and one L/R audio 3.5mm mini-jack
output
• Supports switchable HDMI bypass allowing local monitoring of any
of the HDMI or HDBaseT inputs
• Supports Power over Cable on the CAT5e/6/7 output to a
compatible Receiver
• Supports control via IR, Remote control, RS-232, Telnet WebGUI and
on-panel controls
• Supports HDBaseT LAN serving function to compatible Receivers
Note: The PoC function is only designed for powering compatible
Receiver units only---non-PoC Receiver will need their own
power supply. Receivers of another brand may not be
compatible.
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
1 2 3 65 7 8 9 10 3
4 4
65 7
1POWER: Press this button to turn ON the device and the LED will
illuminated.
2IR Window: This IR receiver receives only the remote control signal
from the packaged included remote control.
3INPUT HDMI 1~4 & LED: Press the IN buttons to select an input source
signal from the 4 HDMI input sources to be display for output ports.
The LED will illuminate according to the selection.
4BYPASS & LED: Press these buttons to select an input source signal
from the 6 input sources to be display for BYPASS output port. The
LED will illuminate according to the selection.
5INPUT CAT5e/6/7 5~6 & LED: Press the IN buttons to select an input
source signal from the 2 CAT5e/6/7 input sources to be display for
output ports. The LED will illuminate according to the selection.
6INPUT PC & LED: Press this button to select PC input source signal to
be display for PC output port. The LED will illuminate according to
the selection.
7INPUT CV & LED: Press this button to select CV input source signal s
to be display for CV output port. The LED will illuminate according
to the selection.
8MENU: Press this wheel to enter into the menu and press it again to
conrm the selection.
9+/-: Press these buttons to move up/down under menu selection or
under volume control to adjust audio volume up/down.
10 ENTER: Press this button to conrm menu selection.
4
6.2 Rear Panel
IR IN
HDMI 1HDMI 2
SERVICE 2
COAX
AUDIO
AUDIO AUDIO 7AUDIO 1 AUDIO 2 AUDIO 3 AUDIO 4
HDMI
BYPASS
CAT5e/6/7CAT5e/6/7 CAT5e/6/7 PC
HDMI 1 HDMI 2HDMI 3HDMI 45 67
INPUT RLCV
8
LAN
RS-232
DC 24 V
OUTPUT
IR OUT
SERVICE 1
ON OFF
DSP PROG.
1
2 6 8 13 14 16
5 7
3 4 7 9 10 12 15 1711
1IR OUT: Connect to the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
2IR IN: Connect to the supplied IR Extender cable for IR signal
reception. Ensure that remote being used is within the direct line-
of-sight of the IR Extender.
3OUTPUT CAT5e/6/7: Connect to the Receiver unit with a Single
CAT5e/6/7 cable for transmission of all data signals.
4OUTPUT HDMI: Connect to a HDMI equipped TV/monitor for display
of the HDMI input source signal.
5OUTPUT COAX: Connect to audio sound equipment such as
speaker or amplier for audio sound output.
6OUTPUT AUDIO: Connect to audio sound equipment such as
speaker or amplier for audio sound output.
7SERVICE 1& 2: These slots are reserved for rmware update use
only.
8DSP PROG Switch: This switch is reserved for rmware update use
only. Default setting is on OFF.
9BYPASS: Connect to a HDMI equipped TV/monitor or DVI equipped
monitor with audio sound equipment such as speaker for both
video and audio output display.
10 INPUT HDMI 1~4 & AUDIO 1~4: Connect to HDMI source equipment
such as DVD or Blu-ray player along or to DVI source equipment
along with audio source signal.
11 INPUT CAT5e/6/7: Connect this port to HDMI to CAT5e/6/7
Transmitter with CAT5e/6/7 cable to extend the signal up to 100m.
12 INPUT PC & AUDIO: Connect this port to PC/Laptop with audio
signal for input signal selecting.
5
13 INPUT CV: Connect this port to source equipment such as video
player or Set-Top-Box for input signal selecting.
14 RS-232: Connect from PC/Laptop for RS-232 command sending to
control the device.
15 LAN: Connect from PC/Laptop with active internet service for Web
GUI control with RJ-45 terminated cable.
16 POWER Toggle: Switch this toggle to turn ON and OFF the device’s
power.
17 DC 24V: Connect the adaptor with power cord included in the
package and connect to AC wall outlet for power supply.
6.3 Remote Control
1POWER:
Press this button to switch the device
ON or to put the device into Standby
mode.
2MUTE:
Press this button to mute output audio
sound.
3INPUT:
Press these buttons one time each
to select input source for outputs
display.
4MENU:
Press this button to enter into the On-
Screen Menu.
5EXIT:
Press this button to exit menu
selection.
6 ▲▼◄►& OK:
Press OK to conrm the selection
or use the directional buttons to
navigate the On-Screen-Menu.
MUTE
CAT5e/6/7
POWER
EXIT MENU
RESET ADJUST
-
+
CR-135
OK
HDMI 1 CAT5e/6/7 1
HDMI 2
HDMI 3
CAT5e/6/7 2
HDMI 4
HDMI 4
HDMI 1 1PC
HDMI 2 2CV
HDMI 3
INPUT
BYPASS
12
5
8
3
9
4
7
6
6
7ADJUST:
Press this button when output image is not tting the display's
screen perfectly. The device will auto adjust the image to full
screen.
8RESET:
Press this button to set the deivice back into the fatory default
setting.
9BYPASS:
Press these buttons to select an input source for Bypass output port
to display.
6.4 IR Pin Assignment
3
1
3
1
2
2
Power
IR Blaster Signal
NC
IR Signal
Power
Grounding
IR Receiver
IR Blaster
Tabla de contenidos
Otros manuales de Convertidor de medios de CYP
CYP
CYP AU-11DD Manual de usuario
CYP
CYP CLUX-H2SDIA Manual de usuario
CYP
CYP CP-255ID Manual de usuario
CYP
CYP EL-7400V Manual de usuario
CYP
CYP CS-802D Manual de usuario
CYP
CYP DCT-24 Manual de usuario
CYP
CYP CSDI-12SR Manual de usuario
CYP
CYP CP-302M Manual de usuario
CYP
CYP DCT-16 Manual de usuario
CYP
CYP CUSB-603 Manual de usuario
CYP
CYP n-TECH SOLUTIONS nT15BX02/CLUX-11CD Manual de usuario
CYP
CYP CM-1391 Manual de usuario
CYP
CYP CSO-T2 Manual de usuario
CYP
CYP DCT-1 Manual de usuario
CYP
CYP CP-259H Manual de usuario
CYP
CYP CPRO-11SI Manual de usuario
CYP
CYP VHC-1 Manual de usuario
CYP
CYP CLUX-14S Manual de usuario
CYP
CYP CLUX-1HLR Manual de usuario
CYP
CYP SY-P290 Manual de usuario
