Curt Group 13458 Manual de usuario

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13458-INS-RA •07/06/2020 •ECN7212 •PAGE 1

Product Registration and Warranty

CURT stands behind our products with industry-leading warranties. To get copies of the product

warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys

Weight Carrying Capacity

Gross trailer weight (GTW) 5,000 lbs.

Tongue weight (TW) 750 lbs.

INSTALLATION MANUAL 13458

Tools Required

Ratchet Socket, 13mm

Torque wrench Socket, 3/4"

Socket extension, 6” Aviation sheers

Safety glasses --

* For a tools reference guide visit

curtmfg.com/trailer-hitch-installation

Level of Difficulty

Easy

Installation difficulty levels are based on time

and effort involved and may vary depending on

the installer level of expertise, condition of the

vehicle and proper tools and equipment.

WARNING

Never exceed the vehicle manufacturer's recommended towing capacity.

SAFETY INSTRUCTIONS

Safety glasses should be worn at all times while installing this product.

NOTICE

Visit www.curtmfg.com for a full-color copy of this

instruction manual, as well as helpful videos, guides and much more!

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

This installation requires:

• Lowering of the exhaust

• Trimming the fascia, if applicable

• Fishwiring

Periodic inspection of the trailer hitch should be performed to ensure all

mounting hardware remains tight and structural components are secure.

To help prevent damage to the product or vehicle, refer to the specified

torque specifications when securing hardware during the installation process.

Parts List

Item Qty Description

1 4 Carriage bolt,

1/2”-13 x 1-1/2”, grade 8

2 4 Square-hole spacer,

1/4" x 1" x 3"

3 4 Serrated-flange nut, 1/2"-13

4 4 Fishwire, 1/2”

5 1 Flange bolt,

M8-1.25 x 35mm, CL 10.9

Product Photo

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13458-INS-RA •07/06/2020 •ECN7212 •PAGE 2

ASSEMBLY

This technique can be used if exhaust

hanger removal pliers are not available.

Using a 5/8" open end wrench, slide

the wrench up to the rubber isolator,

cradling the hanger rod as shown.

Place the ﬂat edge of a pry bar between

the wrench and the hanger stop or hanger

rod. Then simply rotate the pry bar toward

the wrench to remove the rubber isolator.

Note: Using a lubricant or soapy

water on the hanger rod and the

rubber isolator helps removal.

RUBBER ISOLATOR

REMOVAL DIAGRAM

Attach the ﬁshwire to

the carriage bolt and

slide the spacer onto

the ﬁshwire.

Push the bolt through

the hole followed by

the spacer, as shown.

Pull the bolt back into

position, protruding

from the frame.

REVERSE PULL FISHWIRE TECHNIQUE

FRONT

REAR

Insert coiled end of ﬁshwire tool through hitch

mounting hole in vehicle frame rail and out the

access hole. Pass coiled end of ﬁshwire

through spacer and thread bolt into

coil. Kink wire to keep spacer

seperate from bolt as shown.

Pull ﬁshwire, spacer and

bolt through frame and

out mounting hole. Use

ﬁshwire to guide hitch during mounting and

prevent loss of bolt or spacer inside frame rail.

MOUNTING

HOLE

ACCESS

HOLE

FISHWIRE TECHNIQUE

Parts List

Item Qty Description

1 4 Carriage bolt,

1/2”-13 x 1-1/2”, grade 8

2 4 Square-hole spacer,

1/4" x 1" x 3"

3 4 Serrated-flange nut, 1/2"-13

4 4 Fishwire, 1/2”

5 1 Flange bolt,

M8-1.25 x 35mm, CL 10.9

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13458-INS-RA •07/06/2020 •ECN7212 •PAGE 3

Step 1

Lower the exhaust by using a 13mm

socket to remove exhaust hanger bolt

on the bottom of the driver-side frame

rail and removing the exhaust isolator

on the passenger-side frame rail.

This technique can be used if exhaust

hanger removal pliers are not available.

Using a 5/8" open end wrench, slide

the wrench up to the rubber isolator,

cradling the hanger rod as shown.

Place the ﬂat edge of a pry bar between

the wrench and the hanger stop or hanger

rod. Then simply rotate the pry bar toward

the wrench to remove the rubber isolator.

Note: Using a lubricant or soapy

water on the hanger rod and the

rubber isolator helps removal.

RUBBER ISOLATOR

REMOVAL DIAGRAM

Step 2

Fishwire two 1/2” carriage bolts (#1)

and square-hole spacers (#2) into the

rearward most holes in the frame rails.

Reverse fishwire the remaining carriage

bolts and spacers into the access holes.

Insert coiled end of ﬁshwire tool through hitch

mounting hole in vehicle frame rail and out the

access hole. Pass coiled end of ﬁshwire

through spacer and thread bolt into

coil. Kink wire to keep spacer

seperate from bolt as shown.

Pull ﬁshwire, spacer and

bolt through frame and

out mounting hole. Use

ﬁshwire to guide hitch during mounting and

prevent loss of bolt or spacer inside frame rail.

MOUNTING

HOLE

ACCESS

HOLE

FISHWIRE TECHNIQUE

Attach the ﬁshwire to

the carriage bolt and

slide the spacer onto

the ﬁshwire.

Push the bolt through

the hole followed by

the spacer, as shown.

Pull the bolt back into

position, protruding

from the frame.

REVERSE PULL FISHWIRE TECHNIQUE

Step 3

Raise the trailer hitch into position and loosely

secure with 1/2” serrated-flange nuts (#3).

Torque all 1/2” fasteners to 110 lb-ft.

Note: The untextured portion of bumper

cover may need to be trimmed near the

receiver tube if the spacing is too tight.

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13458-INS-RA •07/06/2020 •ECN7212 •PAGE 4

TOWING BASICS & SAFETY INFORMATION

For information on safely towing your trailer, visit curtmfg.com/understanding-towing.

Final Installed Image

Step 4

Reinstall the exhaust isolator and hanger

using the provided M8 flange bolt (#5)

and torque it to 23 lb-ft.

Otros manuales de Accesorios para automóviles de Curt Group

Curt Group

Curt Group Aries 3025175 Manual de usuario

Curt Group

Curt Group Aries TrailCrusher 2156002 Manual de usuario

Curt Group

Curt Group Liverne 401801 Manual de usuario

Curt Group

Curt Group 18320 Manual de usuario

Curt Group

Curt Group 18151 Manual de usuario

Curt Group

Curt Group 58975 Manual de usuario

Curt Group

Curt Group Aries AL235045 Manual de usuario

Curt Group

Curt Group 70105 Manual de usuario

Curt Group

Curt Group 18118 Manual de usuario

Curt Group

Curt Group 16190 Manual de usuario

Curt Group

Curt Group 45143 Manual de usuario

Curt Group

Curt Group ARIES S224046 Manual de usuario

Curt Group

Curt Group Retrac 206820 Manual de usuario

Curt Group

Curt Group Retrac 207800 Manual de usuario

Curt Group

Curt Group 51189 Manual de usuario

Curt Group

Curt Group Aries S224046-2 Manual de usuario

Curt Group

Curt Group UWS TBV-49 Manual de usuario

Curt Group

Curt Group Aries TrailCrusher 2156000 Manual de usuario

Curt Group

Curt Group 40247 Manual de usuario

Curt Group

Curt Group TruTrack 17500 Manual de usuario

Curt Group

Curt Group 45144 Manual de usuario

Curt Group

Curt Group 13387 Manual de usuario

Curt Group

Curt Group ARIES 2051132 Manual de usuario

Curt Group

Curt Group Betterweigh Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario