Curt Group 58975 Manual de usuario

58975-INS-RA •PAGE 1

INSTALLATION MANUAL

Tools Required

Ratchet Cutting tool

Socket extension Electrical tape

Torx bit, T-20 Fish wire

Panel trim

removal tool

Wiring Location(s)

T1 and T2

Level of Difﬁculty

Easy

Hardware Photo

WARNING

Do not exceed product rating or tow vehicle lamp load rating, whichever is lower.

Product Registration and Warranty

CURT Group stands behind our products with industry-leading warranties.

Provide feedback and help us to improve our products by registering your purchase at:

warranty.curtgroup.com/surveys

Maintenance

Periodic inspection of all wires and connections should be performed

to ensure there is no visible damage or loose connections.

Wiring Location Guide*

for Trucks (T)

T1 Behind driver side taillight housing

T2 Behind passenger side taillight housing

T3 Behind driver side rear bumper

T4 Behind center of rear bumper fascia

T5 Behind passenger side rear bumper

T4 T5

* Representative vehicle shown

NOTICE

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

All steps must be followed to ensure the product will function properly. Once installed,

test for proper function by using a test light or connecting a properly wired trailer.

Product Photo

58975-INS-RA •PAGE 2

Step 1

Locate the vehicle battery. Look up the

battery location in the owner's manual of

your vehicle. Disconnect the negative battery

terminal. Be sure to fasten this wire down

and away from the battery when completing

the installation process.

Step 3

Carefully remove the taillight straight back

and out of the vehicle and locate the factory

harness. The connectors will be similar to those

on your new custom wiring product. Separate

the connectors from the taillight housing taking

care not to damage the locking tabs.

Step 2

Open the tailgate. Use a panel trim removal

tool to remove the four push fasteners and

the four T-20 Torx bit screws, two per side,

mounted near the taillight.

Note: Fasterners and screws are

located in the sidewall covered by

the tailgate when in the closed position.

58975-INS-RA •PAGE 3

Step 4B - How to use ﬁsh wire

A) Fish wire is a way to push or pull

an electrical wire through a blind hole.

Make sure the wire is long enough

to stick out on the other side.

Insert the fish wire through the blind

hole and locate it on the other side.

B) Use tape to secure the harness

to the fish wire and pull back up.

The fish wire or harness may get hung up on

something, if this happens you may have to

push back down, wiggle it around or twist the

wire to loosen it from what it’s hung up on.

Fish wire could be anything from a cut-up wire

hanger, stiff wire, rope or string depending on

what is needed for the installation.

Step 4A

Starting on the driver side, use a

fish wire to route down into the inside

of the box in the taillight opening.

Locate the housing end of the RV harness

with yellow wire. Attach it to the fish wire,

and pull through from the bottom of the

vehicle into the taillight opening. Attach the

housing to the driver-side vehicle factory

harness, making sure the connector is fully

inserted with the locking tabs in place.

Step 6

Route the housing end with green wire

to the passenger side along the backside

of the bumper of the vehicle.

Repeat step 5 on the passeneger side

of the vehicle with the green wire.

58975-INS-RA •PAGE 4

Step 7

On the driver side, locate a grounding point near the box such as an existing screw or

bolt in the frame of the vehicle or drill a 3/32"pilot hole. The area should be free from

rust, dirt, and paint (abrasive pad/paper to remove rust and paint). Secure the white

ground wire with the ring terminal on the existing fastener or with the provided ground screw.

CAUTION

Check for miscellaneous items that may be hidden behind or under

any surface before drilling to avoid damage and/or personal injury

Step 8

Attach the taillight to the respective side harness and reinstall.

NOTICE

Once the custom wiring harness is installed, verify that the harness is functioning

by attaching the 4-flat to any vehicle with functioning trailer lights. The taillights

on the tow vehicle should function along with the taillights on the towing vehicle.

Reinstall the taillight fasteners

Step 9

Route the 4-flat along the frame rail on

the driver side. Zip tie as needed along

the frame rail to keep the 4-flat away from

hot spots, pinch points or moving objects.

Loosely secure the zip ties.

Step 10

Route in between the frame and

the fuel tank to the front of the vehicle

and up to the rear of the front tire.

58975-INS-RA •PAGE 5

Step 12

Route the 4-flat harness along the

driver-side inner fender to the front of the

truck. Mount the 4-flat to the inner fender

between the fuse panel and the head light.

Step 13

Use a panel trim removal tool to remove the trim cover. Route the 4-flat wire along the

driver-side inner fender under the removed cover. Zip tie as needed to the front of the

vehicle. Route to just behind the passenger-side head light and mount to the inner fender.

Secure any excess wire so that it is not drooping or dangling, but not so tight that

it causes unnecessary strain to the wire which could lead to breakage over time.

After removing slack from the 4-flat wire, tighten any zip ties and add as needed.

Use a zip tie to fasten any excess wire to a solid spot along the driver-side inner fender.

Reinstall all items removed during install. If it was disconnected at the beginning of the installation,

reconnect the negative battery terminal. Install the provided 4-ﬂat dust cover to help prevent corrosion.

Step 11

Once you reach the rear of the front tire, route

the 4-flat between the body and the frame.

From under the hood, use fish wire to pull

the harness up between the inner and outer

fender to the top of the engine compartment.

Refer to step 4B on how to use fish wire.

Otros manuales de Accesorios para automóviles de Curt Group

Curt Group

Curt Group 11392 Manual de usuario

Curt Group

Curt Group ARIES S224046 Manual de usuario

Curt Group

Curt Group 60638 Manual de usuario

Curt Group

Curt Group Aries 3025175 Manual de usuario

Curt Group

Curt Group 18118 Manual de usuario

Curt Group

Curt Group 60628 Manual de usuario

Curt Group

Curt Group TruTrack 17500 Manual de usuario

Curt Group

Curt Group 45143 Manual de usuario

Curt Group

Curt Group 45144 Manual de usuario

Curt Group

Curt Group Aries TrailCrusher 2156002 Manual de usuario

Curt Group

Curt Group Liverne 401801 Manual de usuario

Curt Group

Curt Group Retrac 207700 Manual de usuario

Curt Group

Curt Group RETRAC 207770 Manual de usuario

Curt Group

Curt Group 18151 Manual de usuario

Curt Group

Curt Group 13387 Manual de usuario

Curt Group

Curt Group UWS TBV-49 Manual de usuario

Curt Group

Curt Group 19279 Manual de usuario

Curt Group

Curt Group 18320 Manual de usuario

Curt Group

Curt Group 51189 Manual de usuario

Curt Group

Curt Group Retrac 207800 Manual de usuario

Curt Group

Curt Group 40247 Manual de usuario

Curt Group

Curt Group Aries AL235045 Manual de usuario

Curt Group

Curt Group Aries S224046-2 Manual de usuario

Curt Group

Curt Group 19750 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario