Createbot R3D S1 Guía del usuario

R3D S1 3D Printer

Quick Operation Guide

*Please read the Quick Operation Guide carefully before using the

product and keep it in a safe place.

Packing list

S1 Machinex1

After opening the product packaging, please confirm whether the 3D printer is in good condition,

and confirm whether the accessories are complete according to the following figure.

Filament Holderx1 Soft magnetic plate

（120x120mm)x1

USB Cablex1

SD Card and Card Readerx1 Wrenchx5Tweezersx1

Appearance introduction

SD Slot

Printing

Platform

Filament Holder Filament

Feed Tube

Filament

Extruder

Operartion Guide

Step1

Install the filament holder

First, aim the inner hole of the filament spool at the plastic part of the wire feed frame, and

gently push it in, then it will buckle up automatically. Note that the tangent direction of

filament is shown in the picture.

Install the filament spool

M4*16 screws

Filament Holder

Insert two M4*16 screws first, then fix them in the threaded holes as specified

and tighten them.

Filament Spool

filament

Step2

SD Card Printing

Copy the file name 3d,gcode into the SD card,and then insert the SD card into the

corresponding card slot.

First put the filament through the feed hole, and then push it in the direction of the feed pipe

until it can't move.

Filament

Feed Tube Faliment

Insert Feed

Filament Loading and Unloading

Note:only one filename is allowed for files

3d.gcode

Adapter installation

Step3

The soft magnetic plate shall be parallel and perpendicular to the platform plate.

Step4

Soft magnetic plate fixed notes

Insert the power adapter into the corresponding DC interface. As shown in the figure, the

machine will automatically print the SD card and wait for about 3 minutes before the

printing starts.

Step5

Check and adjust the pulley

Slicing software installation

Take out the SD card in the 3D printer, copy the slicing software in the SD card(as shown in the

figure below) to the computer desktop, then double-click the installation file to enter the

installation interface, and select the next installation step.

Slice software installation files

After receiving goods at the first time, need to check pulley, because shake can bring about

pulley to sway on orbit, so need to twist screw with Allen wrench inside only half circle

arrives 1 circle till pulley is not shaken so far.

Run the slice parameter configuration for the first time

Open the slicing software, pop up the first run wizard,select the corresponding language,

set the machine to R3D S1,and then Next.

After opening the software, drag the model onto the platform. After waiting for a while,

the model will automatically finish slicing.

select the model, can rotate the model, zoom in and out, mirror command.

After slicing, the file must be saved with a unique name. 3d format is gcode.

Tabla de contenidos

Otros manuales de Impresora 3D de Createbot

Createbot

Createbot S3 Manual de usuario

Createbot

Createbot Super Mini Manual de usuario

Createbot

Createbot Mini I Manual de usuario

Createbot

Createbot MAX Manual de usuario

Createbot

Createbot Mini I Manual de usuario

Createbot

Createbot MINI-Pro Manual de usuario

Createbot

Createbot MaxI Manual de usuario

Createbot

Createbot MaxI Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario