CommScope M3200 Manual de usuario

www.commscope.com

Instruction Sheet 860382035

Issue 5, May 2012

M3200 FTP Modular Panel Instructions

General

The CommScopeM3200 FTP modular panel is a highly flexible 24-port, front or rear accessible patch panel

assembly. When properly grounded and installed with FTP M-series or J-series outlets, modular patch cords,

and cables, it is an integral part of an X1OD FTP connectivity system. The panel consists of a rack mounted

base unit, three slide-in drawers with conductive front bezels, and labels for standard port numbering. It mounts

in a standard 19-inch (483 mm) equipment rack with universal hole spacing and incorporates lugs for panel

grounding.

Ordering information is listed below:

Material ID Description

760058578 M3200 FTP modular panel

A separately orderable removal tool kit (760122713) is required for use with the panel.

M3200 FTP Modular Panel (24-Port)

How to Contact Us

•To find out more about CommScope® products, visit us on the web at http://www.commscope.com/

•For technical assistance:

- Within the United States, contact your local account representative or technical support at

1-800-344-0223. Outside the United States, contact your local account representative or Authorized

Business Partner.

860382035

Instruction Sheet www.commscope.com

Page 2 of 5

- Within the United States, report any missing/damaged parts or any other issues to CommScope

Customer Claims at 1-866-539-2795. Outside the United States, contact your local account

representative or Authorized Business Partner.

Tools Required

•Phillips head screwdriver

Parts List

Verify contents from the parts listed below:

Quantity

Description

Base panel assembly–consisting of a metal panel and three 8-port

bezels mounted in three carriers

Labels and label retainers (labels in one strip)

#12-24 x 1/2” screws

Cable ties

Instruction sheet

WARNING –Important Safety Instructions

When using this product, the following basic safety precautions should be followed to reduce the risk of fire,

electric shock, and injury to persons:

1. Never install communications wiring in wet locations unless it is designed for wet locations.

2. Never install this product during a lightning storm. There is a remote risk of electric shock.

3. Never touch uninsulated communication wiring or terminals unless the communication circuit has been

disconnected at the network interface.

4. Caution: All wiring that connects to this equipment must meet applicable local and national building codes

and network wiring standards for communication cable.

Step 1 ― Mount Panel to Rack

12-24 x 1/2 screws

12-24 x 1/2

screws

1. Using four 12-24 x 1/2" screws supplied, secure panel to rack.

www.commscope.com

860382035

Issue 5, May 2012

Page 3 of 5

Step 2a ― Populate Carrier and Secure Cables to Carrier

1. Cable outlets per the instructions provided

with the individual outlets, then populate

carriers with appropriate outlets.

Note: The upper row of outlets must be

populated before the lower row.

2. Cables should be secured to the carrier

using the supplied cable ties. Tie wrap

two cables (one from upper row and one

from lower row) together to a lug as

shown. Do not tie wrap cables from the

upper row of modules directly to the tie

wrap lugs.

Step 2b ― Remove Carrier from Panel for Front Access Cabling (Alternate)

Captive screws

1. Remove a carrier from base by loosening two captive screws and sliding it forward.

2. Populate the carrier as described in Step 2a above.

Note: Extra cable length is required for the front access cabling method.

3. Reinstall carrier in panel.

Lug

Cable tie

Copper cable

860382035

Instruction Sheet www.commscope.com

Page 4 of 5

Step 3 ― Connect Ground to Panel

Grounding lug

1. Using one of two lug connections provided on rear of panel, ground the panel per approved local

practices.

Step 4 ― Attach Labels and Label Covers

1. Create port labels for each vertical pair of ports. The following methods are recommended:

•Method A – Print the port designations on plain paper and trim to fit the label areas. A template in

Microsoft Word®format is available on the CommScope website under SYSTIMAXM3200 panel

labeling, or it may be obtained from any CommScope representative. A perforated sheet (760060392)

for use in most laser printers is available, or the labels may be trimmed from plain paper. The label

should be 0.43 inches (11 mm) wide and 1.40 inches (36 mm) high.

•Method B – Print the port designations with a standard tape-based labeler. Each labeling area will

accommodate a tape up to 0.43 inches (11 mm) wide and 1.40 inches (36 mm) high.

•Method C – Print the port designations with any type of adhesive labeling system and apply them to the

supplied label cards.

2. Place each label in the area to left of the appropriate pair of ports and secure it with a clear plastic label

cover.

Note: With Method B, it may be desirable to place the label tape on top of a supplied label card in order to

achieve a consistent look.

www.commscope.com

860382035

Issue 5, May 2012

Page 5 of 5

Removing an Outlet Using Outlet Removal Tool (Part of Tool Kit 760122713)

1. Position tool as shown and insert into front of outlet to depress locking tabs.

2. Remove outlet from rear of panel.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de CommScope

CommScope

CommScope ONECELL RP5200 Manual

CommScope

CommScope EHD Manual de usuario

CommScope

CommScope CPP-UDDM-SL-1U-24 Manual de usuario

CommScope

CommScope ION-M7P Manual de usuario

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manual de usuario

CommScope

CommScope TC-96370-IP Manual de usuario

CommScope

CommScope WCS-2 Manual de usuario

CommScope

CommScope NOVUX SEC 100 Manual de usuario

CommScope

CommScope UNJ10G Manual de usuario

CommScope

CommScope AMP NETCONNECT MRJ21 Manual de usuario

CommScope

CommScope ION-U EU H 23/23 Manual de usuario

CommScope

CommScope FPX Series Manual de usuario

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manual de usuario

CommScope

CommScope MRJ21 Quick Fit Cassette Manual de usuario

CommScope

CommScope FOSC-OC-6 Manual de usuario

CommScope

CommScope RUCKUS SmartZone 300 Manual de usuario

CommScope

CommScope SYSTIMAX 360 iPatch G2 MPO Manual de usuario

CommScope

CommScope FPX Series Manual de usuario

CommScope

CommScope Constellation CPT-PP-48C Manual de usuario

CommScope

CommScope Mini-OTE 300 Manual de usuario

CommScope

CommScope NG4access ODF Platform Value-Added Module Manual de usuario

CommScope

CommScope SYSTIMAX 100BASE-T Manual de usuario

CommScope

CommScope SYSTIMAX EHD Manual de usuario

CommScope

CommScope NOVUX DSC 650 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario