Cognex DM 8072DL Manual de usuario
DataMan®8072 DL
Quick Reference Guide
2023 May 04
Revision: 23.2.0.2
Precautions
To reduce the risk of injury or equipment damage, observe the following
precautions when you install the Cognex product:
lThis product is intended for industrial use in automated manufacturing or
similar applications.
lThe safety of any system incorporating this product is the responsibility of
the assembler of the system.
lThis product does not contain user-serviceable parts. Do not make
electrical or mechanical modifications to product components.
Unauthorized modifications can void your warranty.
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
2
lThis product is intended for industrial use in automated manufacturing or
similar applications.
lThe safety of any system incorporating this product is the responsibility of
the assembler of the system.
lThis product does not contain user-serviceable parts. Do not make
electrical or mechanical modifications to product components.
Unauthorized modifications can void your warranty.
3
Symbols
The following symbols indicate safety precautions and supplemental information:
WARNING:This symbol indicates a hazard that could cause death, serious personal injury or
electrical shock.
CAUTION:This symbol indicates a hazard that could result in property damage.
Note: This symbol indicates additional information about a subject.
Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.
4
Product Overview
DataMan 8072 DL Reader
1 Illumination module
2 LEDaimers
3 Illumination LEDs
4 Trigger (press and hold to read)
5 Lanyard hook
6 Indicator light
7 Communication module insertion point
5
Base Station Overview
1 Base station status indicators
2 PAIR sticker - Reading the code pairs the base station
with the device
3Connection point to the reader:
lpairing reader and base station
lnon-wireless communication
lcharging
4 RS-232
5 USB
6 Power plug (24V, max. 15W)
6
7 Alternative power supply connector (24V, max. 15W,
polarity marked on the plastic part near the
connector). Recommended wire diameter is 14- 18
AWG
8 Ethernet
7
DataMan 8072 DL Accessories
Accessory Name Product ID Illustration
Serial/USB slide-in DMCM-SERIALM-00
Ethernet slide-in DMCM-ENETM-00
Bluetooth slide-in DMCM-BTM-00
Charging base station DMA-CBASE-01
Intelligent Bluetooth base station DMA-IBASE-BT-02
Power Supply for base station DMA-24VPWR-xx1
Power Supply for reader DM100-PWR-000
Battery for the wireless reader DMA-HHBATTERY-01
Multi-battery charger DMA-MBC-xx*
POE adapter CPS-24V-POE1
POE adapter CPS-24V-POE4
POE adapter CPS-AC-POE1A-xx2
Wall mount DMA-WALL-8000-00
1xx can be US, EN, UK, or JP.
2xx can be US, EN, UK, or JP.
8
Accessory Name Product ID Illustration
Wall mount for base station DMA-IBASE-WALL-00
Cables
Accesory Name Product ID Illustration
Coiled RS-232 cable for reader, 2.5 m DM8000-RS232-02
Industrial RS-232 cable for reader, 2.5 m DM8000-RS232IND-02
Coiled RS-232 cable for reader, 4 m DM8000-RS232-05
Coiled USB cable, 2.5 m DM8500-USBC-02
Ethernet cable, 2.5 m DM8000-ECABLE-02
Ethernet cable, 30 m DM8000-ECABLE-30
Ethernet cable, 5 m DM8000-ECABLE-05
USB cable, 2.5 m DM8500-USB-00
Coiled Ethernet cable, 5 m DM8000-ECABLEC-05**
RJ25 (RJ12) to DSUB9 cable for base station, 5 m DMA-RS232RJ-05
9
** Collimated cable length including DM8000-ECABLE-X should not
exceed 50 m.
lUSB cable for base station: Use any standard USB-A to USB-B
2.0 cable up to 3 meters.
lEthernet cable for base station: Use any standard CAT5/5e,
SF/FTP or S/FTP cable.
lDMA-USB-00: Straight 10ft USB cable.
10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Lector de código de barras de Cognex
Cognex
Cognex DataMan 8072 Verifier Manual de usuario
Cognex
Cognex DataMan 100 Manual de usuario
Cognex
Cognex DataMan 100 Manual de usuario
Cognex
Cognex DataMan 300 Series Manual de usuario
Cognex
Cognex DataMan 8600 Series Manual de usuario
Cognex
Cognex DataMan 150 Manual de usuario
Cognex
Cognex DataMan 8600 Series Manual de usuario
Cognex
Cognex DataMan 60 Series Manual de usuario
Cognex
Cognex DataMan 300 Series Manual de usuario
Cognex
Cognex DataMan 8072 ER Manual de usuario
Cognex
Cognex DataMan 503 Manual de usuario
Cognex
Cognex DataMan DT150 Manual de usuario
Cognex
Cognex DataMan 8072 DL Manual de usuario
Cognex
Cognex DataMan 8700 Manual de usuario
Cognex
Cognex DataMan 260 Series Manual de usuario
Cognex
Cognex DataMan 300 Series Manual de usuario
Cognex
Cognex DataMan 7550 Manual de usuario
Cognex
Cognex DataMan 8700 DX Manual de usuario
Cognex
Cognex DataMan 200 Manual de usuario
Cognex
Cognex DataMan 360 Series Manual de usuario
