Cognex DataMan 8072 DL Manual de usuario
DataMan®8072 DL
Quick Reference Guide
2019 October 08
Revision: 6.1.6SR1.5
Precautions
To reduce the risk of injury or equipment damage, observe the following precautions
when you install the Cognex product:
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
2
Product Overview
1 Illumination module
2 LEDaimers
3 Illumination LEDs
4 Trigger (press and hold to read)
5 Lanyard hook
6 Indicator light
7 Communication module insertion point
3
Base Station Overview
1 Base station status indicators
2 PAIR sticker - Reading the code pairs the base station
with the device
3Connection point to the reader:
lpairing reader and base station
lnon-wireless communication
lcharging
4 RS-232
5 USB
6 Power plug (24V, max. 15W)
7 Alternative power supply connector (24V, max. 15W,
polarity marked on the plastic part near the connector).
Recommended wire diameter is 14- 18 AWG
8 Ethernet
4
DataMan 8072 DL Accessories
Serial/USB slide-in DMCM-SERIALM-00
Ethernet slide-in DMCM-ENETM-00
Bluetooth slide-in DMCM-BTM-00
Charging base station DMA-CBASE-01
Intelligent Bluetooth base station DMA-IBASE-BT-02
Power Supply for base station DMA-24VPWR-xx*
Power Supply for reader DM100-PWR-000
Battery for the wireless reader DMA-HHBATTERY-01
Multi-battery charger DMA-MBC-xx*
POE adapter CPS-24V-POE1
POE adapter CPS-24V-POE4
POE adapter CPS-AC-POE1A-xx*
Wall mount DMA-WALL-8000-00
Wall mount for base station DMA-IBASE-WALL-00
Stand DM-STAND-00
*xx can be US, EN, UK, or JP.
5
Cables
Coiled RS-232 cable for reader, 2.5 m DM8000-RS232-02
Industrial RS-232 cable for reader, 2.5 m DM8000-RS232IND-02
Coiled RS-232 cable for reader, 4 m DM8000-RS232-05
Coiled USB cable, 2.5 m DM8500-USBC-02
Ethernet cable, 2.5 m DM8000-ECABLE-02
Ethernet cable, 30 m DM8000-ECABLE-30
Ethernet cable, 5 m DM8000-ECABLE-05
USB cable, 2.5 m DM8500-USB-00
Coiled Ethernet cable, 5m DM8000-ECABLEC-05**
RJ25 (RJ12) to DSUB9 cable for base station, 5 m DMA-RS232RJ-05
** Collimated cable length including DM8000-ECABLE-X should not exceed 50 m.
lUSB cable for base station: Use any standard USB-A to USB-B 2.0 cable up to 3 meters.
lEthernet cable for base station: Use any standard CAT5/5e, SF/FTP or S/FTP cable.
lDMA-USB-00: Straight 10ft USB cable.
6
Field of View and Reading Distances
DataMan 8072 DL with a 6.2 mm Lens (Standard Range, Focused to 75 mm)
Device Distances in mm/1D min. code Distances in mm/2D min. code
DM8072 20-170 6 MIL 0-200 10 MIL
0-200 10 MIL 0-260 15 MIL
0-260 15 MIL 0-300 20 MIL
7
Connecting the Reader
Bluetooth Readers
1. Connect the slide-in to the reader and tighten the screws to lock the slide-in.
2. Insert the battery.
3. Insert the plug.
Corded Readers
1. Connect the slide-in to the reader and tighten the screws to lock the slide-in.
2. Insert the plug. Slide the cable lock up to the reader and twist the cable lock
in place.
Note: Disconnect the DataMan 8072 from power or remove the battery before inserting/removing the
communication modules.
8
Installation
Installation procedures and specifications are presented in detail in the DataMan
8072 DL Reference Manual, which is installed with the DataMan Setup Tool. From
the Windows Start menu, select the following to access the manual: All Programs >
Cognex > DataMan Software vx.x.x > Documentation.
Note:
lCables are sold separately.
lIf a standard component is missing or damaged, immediately contact
your Cognex Authorized Service Provider (ASP) or Cognex
Technical Support.
CAUTION:All cable connectors are "keyed" to fit the connectors on the
DataMan system; do not force the connectors or damage may occur.
Install Software and Documentation and
Connect the Reader
To configure a DataMan 8072 DL reader, the DataMan Setup Tool software must
be installed on a networked PC. The DataMan Setup Tool is available from the
DataMan support site: http://www.cognex.com/support/dataman.
1. After installing the software, connect the DataMan 8072 DL to your PC.
2. Launch the DataMan Setup Tool and click Refresh.
3. Select your DataMan 8072 DL reader from the list and click Connect.
9
DataMan 8072 Specifications
Weight 254 g (without slide-in)
Operating Temperature 0ºC — 40ºC (32ºF — 104ºF)
Storage Temperature -10ºC — 60ºC (14ºF — 140ºF)
Maximum Humidity < 95% (non-condensing)
Environemntal IP65
Codes 1-D barcodes: Codabar, Code 39, Code 128, and Code 93, Interleaved 2 of 5,
Pharma, GS1 DataBar, Postal, UPC/EAN/JAN, DataBar
2-D barcodes: Data MatrixT M ; QR Code and microQR Code, RSS/CS, PDF 417,
MicroPDF 417, MaxiCode, Aztec Code
Power Supply Requirements USB: external 5.0 W maximum LPS or NEC class 2 power supply: +5V - +6V DC
RS232 external 5.0W max LPS or NEC class 2 power supply
+6.0V 1A DC (5.0m RS-232 cable)
+6.0V 1A DC (2.5m RS-232 cable)
ETH: Class 2 PoE supply IEEE 802.3af (connect only to PoE networks without
routing to the outside plant)
Inrush current peak 5A maximum
Duration: approx. 30μs
Electrical charge: 60μAs at 6V
Battery life for wireless
reader (typical use case)
ca. 4100 triggers can be operated within a 13 hour working shift
Ethernet 10/100 Base-T FULL/HALF DUPLEX, IEEE 802.3
Bluetooth Bluetooth™ 2.1, 2.4 GHz
DataMan 8072 Imager Specifications
Specification DataMan 8072 Imager
Image Sensor 1/3 inch CMOS
Image Sensor Properties 3.75 μm square pixels
Image Resolution (Pixels) 1280 x 960
Lens Type 6.2 mm F:10 lens
10
Otros manuales para DataMan 8072 DL
2
Tabla de contenidos
Otros manuales de Lector de código de barras de Cognex
Cognex
Cognex DataMan DT150 Manual de usuario
Cognex
Cognex DataMan 380 Series Manual de usuario
Cognex
Cognex MX-1000 Manual de usuario
Cognex
Cognex DataMan Instrucciones de funcionamiento
Cognex
Cognex DataMan 360 Series Manual de usuario
Cognex
Cognex DataMan 470 Series Manual de usuario
Cognex
Cognex In-Sight SnAPP Series Manual de usuario
Cognex
Cognex DataMan 280 Series Manual de usuario
Cognex
Cognex DataMan 370 Series Manual de usuario
Cognex
Cognex DataMan 60 Manual de usuario
Cognex
Cognex DataMan 8700 Manual de usuario
Cognex
Cognex DataMan 503 Manual de usuario
Cognex
Cognex DataMan 8050 Manual de usuario
Cognex
Cognex DM8072 ER Manual de usuario
Cognex
Cognex DataMan 280 Series Manual de usuario
Cognex
Cognex DataMan 9500 Manual de usuario
Cognex
Cognex DataMan 8600 Verifier Series Manual de usuario
Cognex
Cognex DataMan 470 Series Manual de usuario
Cognex
Cognex DataMan 260 Series Manual de usuario
Cognex
Cognex DataMan 8000 Series Manual de usuario
