Clevertronics ECFLED-LI-TH Series Instrucciones de instalación y funcionamiento

1942251 V1.1 February 2018

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails

to remain illuminated for the requisite time, remedial action must be taken to repair the situation

and once completed, the unit must pass a subsequent test. For more specific information, please

refer to the current edition of the AS 2293.3 Standard.

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The Green LED Test Switch indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Fault: Green LED flashes once every 5 seconds-Battery is disconnected

Check: Battery is connected.

Fault: Green LED blinks off once every 5 seconds- Charging very flat battery

Allow 20min to recover battery then recheck

Fault: Green LED flashes at 2Hz (Fast flash)- Faulty battery

Replace battery

Rated Emergency Lumen Output in accordance with AS2293.1 (refer to

spacing tables for installation positions):

N/A for Theatre Mask

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The Li-ion battery in this fitting has been selected to give excellent long life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

ECFLED-LI-TH

Economy Lithium Cleverfit LED Theatre Exit

Installation & Maintenance Instruction Leaflet

Designed in Australia to comply with the requirements

of AS2293.3: 2005 and AS/NZS CISPR15: 2011.

Victoria (Head Office & Manufacturing)

195 Chesterville Rd Moorabbin VIC 3189

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

News South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9248 3720

Fax: +61 8 9248 3725

New Zealand

Phone:+64 800 548 448

Models: ECFLED-LI-TH-yy

Options

yy=E

Exit

yy=R

Running man

yy=ER

Exit with Right Arrow

yy=RR

Running main with Right Arrow

yy=EL

Exit with Left Arrow

yy=RL

Running main with Left Arrow

yy=DS-R

Double sided Running Man

yy=DS-RAOW

Double sided Running Man with Arrow

Spare Parts:

1560200

Battery :EcoLith 3.2V 1.1Ah 210mm lead,noBKT

8002900

PCA: LED Strip ECFLED-LI CT10242-D1

8002880

PCA: Driver ECOLITH Cleverfit CT10240-L4

Important:

It is illegalfor anyone, except for a licensed electrician toinstall ormaintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1942251 V1.1 February 2018

Installation:

The Economy Lithium Cleverfit LED Theatre Exit (ECFLED-LI-TH) can be installed either Ceiling or Wall

Mounted and can be mounted perpendicular to a wall using the (optional) Cleverfit Cantilever Bracket.

The ECFLED uses a “slide connect bracket base” that is mounted and wired into position first. The main

body can be installed once the base is wired or later to avoid damage during the construction phase.

Please follow the steps below to install the Cleverfit Exit:

•Disengage the slide connect bracket from the exit body. Position the base in the mounting position.

•Using the bracket as a guide, mark 2 holes for mounting and one for mains access. Then install the

bracket using appropriate fixings (not supplied).

•Connect the 240VAC supply to the mounting bracket.

•Configure all the mounting parts and cable entry points as below (if required) and engage the body

into the slide connect bracket. Apply mains power and check that the Cleverfit Exit is operational.

Images and Dimensions

Cleverfit Maintenance:

Lamp Replacement:

•Use only the lamp(s) recommended on the label inside the Cleverfit.

•To replace the lamp bar, remove the self-tapping screws, disconnect the signal cable and install

the new lamp bar.

*Please note that the 50,000 hour LED Lamp Bar used in the Cleverfit Exit does not suffer from burn

out. Lamp replacement can be done as scheduled maintenance, at >5 year intervals. Please make a

note, in the site logbook, as to when lamps should be changed.

Battery Replacement:

•Use only the battery recommended on the label inside the Cleverfit and on this instruction.

•Remove the screw securing the fitting to the mounting bracket.

•Remove the fitting from the bracket by sliding it forward.

•The battery is located in the top of the fitting. See images.

•Remove the clip holding the battery.

•Unplug the battery from the PCA and remove it.

•Insert the new battery into the holder, route the DC cable to the PCA and plug the new battery into

the connector.

•Secure the battery using clip.

Changing Exit Legend Inserts:

The Legend of the Cleverfit Theatre Exit can be replaced. Replacement legends can be ordered from

Clevertronics.

Mounting Bracket - front view

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ARGO-1200 EM Series Especificaciones técnicas

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics FBS2LED-DIF Series Manual de usuario

Clevertronics

Clevertronics Argonaut PLUS Guía de mantenimiento y servicio

Clevertronics

Clevertronics L10 LJELED-40 Series Manual de usuario

Clevertronics

Clevertronics L10 LWPLIFE PRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ARGOPRO-1200 Series Manual de usuario

Clevertronics

Clevertronics Trade Series Manual

Clevertronics

Clevertronics CleverEVAC L10 Cleverfit Pro DYRL CP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics l10 LBULKy Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics EJELED-40-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Argonaut Manual de instrucciones

Clevertronics

Clevertronics L10 Ultrablade Pro LUBPRO-SM Series Manual de instrucciones

Clevertronics

Clevertronics L10 Cleverfit Pro Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Weatherproof Jumbo LED Exit Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Argonaut PLUS Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LUBPRO Series Manual

Clevertronics

Clevertronics LED CIRCLITE Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Cleverfit CCFLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Lifelight Pro LWPLIFE-PRO-WM Series Instrucciones de instalación y funcionamiento

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario