Clevertronics Glider Instrucciones de instalación y funcionamiento

1942591

V1.0

3 November 2022

Instruction Sheet Template - V1.5 –Updated 09/06/2022

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails

to remain illuminated for the requisite time, remedial action must be taken to repair the situation

and once completed, the unit must pass a subsequent test. For more specific information, please

refer to the current edition of the AS 2293.3 Standard.

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The Green LED Test Switch indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Fault: Green LED flashes once every 5 seconds-Battery is disconnected

Check: Battery is connected.

Fault: Green LED blinks off once every 5 seconds- Charging very flat battery

Allow 20min to recover battery then recheck

Fault: Green LED flashes at 2Hz (Fast flash)- Faulty battery

Replace battery

Changing Exit Legend Inserts:

The Exit comes with an assortment of standard legends.

1. To remove the legend, grasp the centre of the bottom trim piece and pull down slightly to

expose the legend edge. See photo.

2. Grasp the bottom edge of the legend and slide the existing legend out of the blade, while

working the edges out along the sides.

3. Slide the new legend into the blade, ensuring to fit the edges into the sides then slide the

legend to the top of the blade. Insert one bottom corner then the other. Slide the legend down

into the bottom trim.

Glider Exit

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements

of AS2293.3: 2018, AS CISPR15: 2017

Models:

GLIDER

Spare Parts:

1560180

Replacement Battery

8012080

Replacement Emergency LED Board

8003553

Replacement Emergency Driver

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1942591

V1.0

3 November 2022

Instruction Sheet Template - V1.5 –Updated 09/06/2022

Installation:

The GLIDER is a recessed ceiling mount fitting. The GLIDER can be attached directly to any solid surface, or to

a ceiling tile with the integrated Spring Clips. The GLIDER comes with an attached Flex and Plug. Please follow

the steps below to install the Exit:

•Create a cut-out (345mm x 65mm) in the mounting surface.

•Route the power cord to the mains connection and connect the 240VAC supply.

•Carefully fold up both spring brackets located on the sides of the Exit and insert the Exit up through the

ceiling while letting the Spring brackets close and latch onto the upper surface of the ceiling panel.

•Make sure the fixture is properly secured to the ceiling before releasing support and completing install.

•The Minimum ceiling thickness is 0mm and maximum ceiling thickness is 25mm.

•Alternately, fix the GLIDER to a solid surface using (4) screws through Screw Holes (see image).

•Apply power to the fitting and test.

Maintained/Non-Maintained Operating Mode:

Press the Test Button 5 times within a 4 second period to toggle operation of the fitting between

Maintained and Non-Maintained mode.

Battery Replacement:

•Use only the battery recommended on the label on the Exit and on this instruction.

•Remove the exit from the mounting surface. Take extra care around the sides where the Spring

Clips are compressed.

•The battery is located in the top of the fitting.

•Remove the battery Cover.

•Unplug the battery from the PCA and remove it.

•Insert the new battery into the holder, route the DC cable to the PCA and plug the new battery into

the connector.

•Close the battery cover and insert the Product back into the Ceiling cavity.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

This luminaire (with reinforced insulation between control/LED terminal and AC Supply) contains non-

user replaceable light source –to be replaced (if required) by the manufacturer or his service agent or a

similar qualified person.

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics L10 Ultrablade Pro LUBPRO-SM Series Manual de instrucciones

Clevertronics

Clevertronics TS EUBPRO-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LUBPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Argonaut PLUS Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP CWSQLED Series Manual

Clevertronics

Clevertronics Trade Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics l10 LBULKy Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LLIFE-PRO-WP-IPREM Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics EL EUBPRO-SM-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Argonaut PLUS Manual de usuario

Clevertronics

Clevertronics FBKLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP LIFELIGHT CLIFE-RECSP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ECFLED-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CCIRC Series Instrucciones de funcionamiento y mantenimiento

Clevertronics

Clevertronics LP CSBLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CBULKy Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP CCFPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Argonaut Manual de instrucciones

Clevertronics

Clevertronics L10 Weatherproof Jumbo LED Exit Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Trade TS CIRCLITE ECLLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CWP2LIFE-PRO-WPPOD Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics GLIDER-SM Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP Argonaut ARGOSQ-LP Series Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario