Clear-Com PM-220 Guía de solución de problemas

RM-220

2-CHANNEL REMOTE STATION

INSTRUCTION

and

SERVICE MANUAL

Clear-

COlli

Intercom Systems

945 Camelia st. Berkeley, California 94710 510-527-6666

Clear-Com 810193

8/24194

REV

. A

Clear-Com Systems

-220 2-Channel Remote Station

Instruction Manual

PIN 810193

All

Rights Reserved

Clear-Com Systems

945 Camelia

St.

Berkeley,

Ca.

94710

U.S.A

While Clear-Com makes every attempt to maintain the accuracy

the information

contained in its

product

manuals, that information

subject to

change

without

notice.

RM-220 2 Channel Remote Station

CLEAR-COM LIMITED WARRANTY

Clear-Com products are warranted to

free from defects

materials

and

workmanship

for a period

one

year

from the date

sale.

Clear-Com's sole obligation during the warranty period

to provide, without

charge, the parts

and

labor necessary to remedy covered defects appearing

products returned prepaid to Clear-Com, 945 Camelia St., Berkeley,

Ca.

94710-1484, U.S.A.

This warranty does

not

cover any defect, malfunction

failure

caused

beyond

the control

Clear-Com, including unreasonable

negligent operation,

abuse, accident, failure to follow instructions in the Manual, defective or im-

proper

associated equipment, attempts at modification

and

repair

not

autho-

rized

Clear-Com,

and

shipping damage. Products with their serial numbers

removed

defaced are not covered

this warranty.

obtain warranty service, follow

the

procedures described

below

IIProced-

ures for Returnsll

and

IIShipping

Manufacturer for Repair

Adjustment.

This warranty is the sole

and

exclusive express warranty given with respect to

Clear-Com products.

is the responsibility

the

user

to determine before pur-

chase that this product is suitable for

the

user's intended purpose.

Any

and

all implied warranties, including the implied warranty

merchantability are limited to the duration

this express limited warranty.

Neither Clear-Com

nor

the dealer

who

sells Clear-Com products is liable for

incidental

consequential damages

any kind.

Return Shipping Instructions

Procedures for returns:

-If

repair

necessary, contact the dealer

where

the unit

was

purchased.

-If

repair through the dealer is not possible, contact the Clear-Com Custom-

Service Department, located at the factory, as directed below.

They

will is-

sue

a Return Authorization Number eRMA).

-Do

not

return

any

equipment to the factory without first obtaining a Return

Authorization Number.

4 RM-220 2 Channel Remote Station

-Be

prepared

to provide your

companys

name, address,

phone

number,

name

person

to contact regarding the repair, type

and

quantity

the

equipment, description

the defect,

and

the

equipment

serial number(s).

Questions regarding returns for repair should

directed to:

Customer

Service

Department

Clear-Com

Intercom

Systems

945 Camelia Street

Berkeley, California 94710-1484

Telephone:

(510) 527-6666

Fax: (510) 527-6699

Shipping to Manufacturer for Repair

Adjusbnent

All

shipments

Clear-Com equipment must be

prepaid

via United Parcel Ser-

vice

the

best available shipper. The

equipment

should

shipped

the

original packing container; however,

the original container is

not

available,

use

a suitable container that is rigid

and

adequate

size.

a substitute con-

tainer is used, the equipment should

wrapped

paper

and

surrounded

with

least four inches

excelsior

similar shock-absorbing material. A de-

tailed description

the

problem

work

done

should

included.

All

shipments should

directed to

the

attention

the Customer Service Depart-

ment

and

must include the Return Authorization Number.

Upon

completion

repairs, equipment will

returned collect via United Par-

cel Service

other specified shipper.

NOTICE

ABOUT

SPECIFICATIONS

Performance specifications included in this manual are deSign-center specifica-

tions

and

are included for customer guidance

and

facilitate system installa-

tion. Actual operating performance may vary.

BEFORE YOU BEGIN .

get

the

most

out

the

RM-220

Main Station, read this manual carefully.

will

answer

questions

you

might have

about

the

operation

and

service

the

components in the system. Included

a Troubleshooting Section that provides

causes

and

possible solutions to problems

you

might

have

with system

and

component

operation. Clear-Com's Customer Service

Department

is available

answer questions

not

covered in this manual.

Rev. A © Clear-Com Intercom Systems1994

RM-220 2 Channel Remote Station

THE CLEAR-COM CONCEPT

Clear-Com

a closed-circuit intercom system that consistently provides high-

clarity communication in high-noise and low-noise environments. A basic sys-

tem consists

a single- or multi-channel

power

supply

main station con-

nected to various single-

multi-channel remote stations,

such

as beltpacks

and

loudspeaker stations.

Clear-Com manufacrures a wide variety

both portable

and

fixed-installation

units.

All

are compatible with

each

other. Clear-Com intercom systems

can

also interface with

?ther

communication systems

and

devices.

Clear-Com stations are interconnected with two-conductor, shielded micro-

phone

cable, using 3-pin

XLR

connectors.

One

wire carries

the

power

(28-30 volts) from a main station or power supply to all remote stations,

and

the

other wire carries 2-way (duplex) audio information. The shield acts as a

common

ground.

One

termination

(per

channel)

needed

throughout the in-

tercom network,

and

usually located

the

main station or

power

supply.

Clear-Com

a distributed amplifier system; each main

and

remote

station

houses its

own

mic preampliller, headset

speaker

power

amplifier,

and

signaling drcuitry. Low-impedance mic input lines (200 Ohms)

and

specially

designed circuitry make Clear-Com channels virrually immune to

RFI

and dim-

mer

noise.

Clear-Com main stations, power supplies

and

certain remote stations

each

have

auxiliary program input with its

own

volume control, which allows

exter-

nal audio source to

fed to the intercom system.

Visual Signal Circuitry

(CALL

Lights), a standard fearure

most main

and

re-

mote stations, allows the user to attract the attention

operators

who

have re-

moved their headsets.

Depending

upon

the type

main

and

remote stations selected

and

assuming

that

enough

power

available, a maximum

number

remote stations

from

(all speaker stations) to 30 (all headset stations)

can

distributed

along a mile

wire. Remote stations bridge the intercom line

a very high

impedance (>10 KOhms), and place a minimum load

the line.

The

audio

level always remains constant, and does not flucruate

stations leave

and

join

the

network.

6 RM-220 2 Channel Remote Station

DESCRIPTION

The

"PL-Pro"

RM-220

one

a series

professional intercom stations specifi-

cally designed for the broadcast industry. This 2 channel,

one

rack

space

sta-

tion

ideal for

ENG

and

EFP

trucks, production studio consoles,

and

small

facilities. The station can

tailored

your

needs through it's programmable

"Talk"

button options. The

RM-220

compatible with all Clear-Com Party-Line

intercoms,

The station also incorporates a single channel program interrupt system (lFB)

the

station. When activated,

one

more stations

can

interrupt

the

program

to a talent with Clear-Con's wired

wireless talent receivers. Direct connec-

tion

Clear-Corn's

IFB

system

easily accomplished through a 1/4 inch

phone

jack

the rear panel intended to directly connect

a Clear-Com

MA-4.

The

RM-220

remote

speaker/

headset station allows selectable two channel

talking

and/or

listening

a Clear-Com Intercom System.

The

operator can

communicate

either

the channels separately

both

at once. Illumi-

nated dual action talk buttons are electronic momentary

latching.

The

latch-

ing feature may

disabled if desired. Also the talk buttons can

remote

controlled for footswitch

other use. Monitoring activity

possible through

the

speaker

headset

both at once.

The

RM-220

features Visual

Call

Signaling to attract the attention

operators

who

have removed their headsets

turned off their speakers.

This station accepts dynamic headsets. The station accepts two different

lengths

plug-in gooseneck microphones,

and

18",

allow for different

operating locations/positions.

The station's speaker can

turned

off

a convenient front

panel

switch

when

private conversation via the headset

desired. A "speaker dip-

ping" circuit will give you

additional amount

acoustic output before feed-

back. This feature helps

reduce feedback

when

stations are placed

proximity

each other. The station accepts a balanced Program

input

for

mOnitoring external audio in the headset

speaker. Individual sidetone con-

trols for

each

channel allows the operator

vary the level

his/her

own

voice as heard in the headset/speaker.

Rev. A @ Clear-Com Intercom Systems1994

RM-220 2 Channel Remote Station

"Studio Announce" allows control

a paging

speaker

a studio. A front

pan-

button

activates this function

and

assodated

relay.

The

RM-220

installs

a standard

19"

equipment

rack, using

only

one

rack

space

The

station provides

two

3-pin,

XLR

connectors for

Input

and

loop-

through

each

channel.

TECHNICAL SPECIFICATIONS:

CONTROL SYSTEM:

CMOS Digital Logic

and

Signal Switching

HEADSET MICROPHONE PRE-AMP:

Dynamic Headset Input

Impedance

---

- 1 KOhms

Input Level -55

dBv*

nominal

Frequency Response: 250 Hz

12 KHz,

contoured

for intelligibility.

Gain from Headset

Intercom Line:

+41

PANEL MICROPHONE PRE-AMP:

Input

Level

------------

dBv*

nominal

Frequency Response: 250 Hz

12 KHz,

contoured

for intelligibility.

Gain from Panel

Mic

Intercom

Line:

+31

dB (adjustable)

SPEAKER AMPLIFIER:

Load Impedance:

----------

Ohms

Output

Level: at least 4 watts

Distortion:

THD at 1 KHz

Frequency Response: 200-18KHz +/-2dB

HEADPHONE AMPLIFIER:

Load Impedance:

----------

greater

than

Ohms

Output

Level: at least +20

dBv*

across 600

ohm

Distortion:

------------

<0.2% THD

1 KHz

Frequency Response: 200-18KHz +/-2dB

Gain from Intercom Line: +37 dB

PROGRAM INPUT:

Input

Level

Ref.:

----------

-10

dBv*

Input

Impedance

: >40 KOhms

Frequency Response: 150 Hz to 15 KHz

8 RM-220 2 Channel Remote Station

INTERCOM LINE DRIVE/RECEIVE CIRCUITS:

Impedance, Output Load:

------

> 10 KOhms (200Hz -10 KHz)

Level, Line (200

ohm

load): -9

dBv*

(nominal) +5dBv (max

before clip)

Sidetone Null Capability:

-------

dB (200Hz -10 KHz)

Crosstalk, Station Induced Ch. to Ch.: >60 dB

Noise,

Ratio

Listen Channels: >60 dB

LINE LEVEL OUTPUTS:

(Announce)

Type

anced

Impedance

---

-~---

600

ohms

Level 0 dBv

IFB/HOT

MIC:

Type

--------

---------

Unba~nced

Impedance

---------

600

ohms

Level 0 dBv

STANDARD CLEAR-COM SYSTEM SPECIFICATIONS:

Usable Line Quality:

--------

> 100 Stations

Total Line Length

One

Channel > 5000 feet

CONNECTORS:

Intercom:

----

------

XLR-3

(2-CH

2-CH B)

Accessory DB-15F

Program Input

output

Foot Switch Logic Inputs

IFB/HOT

MIC.

---

-----1/4

inch

Phone

Jack

POWER REQUIREMENTS:

Source Intercom Line

Voltage

------------

-30

VDC

Current 65

rnA

idle, 120

rnA

average

PHYSICAL SPECIFICATIONS:

Dimensions:

-------------

19"W x 1.75"H x 7

(483mm x 44.5mm x 178mm)

Weight:

------------

3.6 lbs 0 .6 Kg)

Operating Temperature Range: 32-122° F

CO-50°

• -

OdBv

= 0.775 volts

RMS.

(Specifications subject to change without notice.)

Rev. A © Clear-Com Intercom Systems1994.

RM-220 2 Channel Remote Station

INSTALLATION

This section discusses the installation

the

RM-220

intercom system.

Typical applications, overall installation theory,

and

detail

each

connector,

and

adjustment

the

RM-220

are discussed.

INSTALLATION OVERVIEW

This section describes the Clear-Com concept in intercom line interconnection.

The

following subjects are discussed:

• Intercom Line Connection

• Line Termination

• Station Powering

• Cable Considerations

Intercom Line Connection:

The

RM-220

provides a male

and

female

XLR-3

connector for

each

intercom

line that

are

"looped through".

Line Termination:

The

fundamental concept

Clear-Com Party-Line intercom is that all stations

provide high impedance current sourced signals into a single

common

system

termination.

The

line drivers in a station have a source

impedance

greater

than

10 KOhms.

The

receive

"listen" section

stations contain a 'hybrid null' circuit that at-

tempts

reject (null) any "talk" signal being sent

that station

that chan-

nel.

The

'hybrid null' circuit

depends

known

impedance

the

intercom

line

accomplish this. Variations in impedance

the

line

upset

the

'null'.

CAUTION:

All

Clear-Com Intercom lines must

terminated.

Care

must

taken

not

fail

terminate

'double' terminate a line.

All

unused

in-

tercom inputs must

terminated to

keep

the

line drive circuits stable.

The

RM-220

does

not

provide termination

the intercom line. Clear-Com

main stations

and

power

supplies provide switch selectable termination net-

works

all intercom

output

lines. It

the

user

determine

where

the

termination will

provided.

unterminated line will cause excessive levels,

possible oscillation

line drivers,

and

sever unbalance

hybrid null net-

works. A

double

multiple terminated line will cause

low

levels

and

sever

unbalance

hybrid null circuits.

10 RM-220 2 Channel Remote Station

The

termination

intercom line (or channel) is a 220

Ohm

resistor in series

with a 4.7 KOhm that

paralleled with a

uF capacitor.

Station Powering:

The

RM-220

needs +20 to

+30

volts between pins 1

and

the intercom con-

nectors. Typical Clear-Com systems are powered

a Main Station

a Power

Supply.

Clear-Com

power

supplies can

paralleled to increase the

number

RE-

MOTE

STATIONS

that can

operated in a system.

Cable Considerations:

The

Clear-Com intercom line

intended to run

a shielded twisted pair

cable

per

channel

intercom.

One

conductor carries full duplex ("two-way")

audio, the

other

conductor carries the

power

for remote stations.

The

shield

used

for ground return for audio

and

power.

When

choosing inter-

connect cable,

keep

the following considerations in mind:

resistance

the ground

common conductor affects crosstalk.

For runs longer than 500 feet

not

use wire smaller

than

20 gauge.

2 The capacitance

the interconnect cable affects system frequency

response

and

sidetone stability. Total capacitance should

not

greater than 0.25

uFo

Portable Installation Cable: Practical cable for portable system interconnec-

tions

flexible, two-conductor, shielded microphone cable. For runs less than

500 feet a cable

made

gauge wire is acceptable. For runs longer than 500

feet

use

a 20 gauge cable

larger.

Permanent

installation Cable: Vinyl-jacketed shielded pair

the cable

choice for permanent installations. Use a low-capacitance

gauge

wire for

short runs

(under

500 feet) and 18 gauge cable for runs greater

than

500 feet.

Placing the cable in conduit

recommended but not necessary.

Multi-pair cable that is indiVidually shielded is acceptable for use in multi-

channel systems. For cross-talk considerations the shields must

tied togeth-

both

ends

the cable to

produce

the lowest possible

path

for

ground

return.

Tabla de contenidos

Otros manuales de Sistema de intercomunicación de Clear-Com

Clear-Com

Clear-Com ECLIPSE EASI-PICO MATRIX Manual de usuario

Clear-Com

Clear-Com Encore V-Box Manual de usuario

Clear-Com

Clear-Com WBS-680 Manual de usuario

Clear-Com

Clear-Com Tempest 900 Manual de usuario

Clear-Com

Clear-Com Eclipse HX-Median Manual de usuario

Clear-Com

Clear-Com WBS Manual de usuario

Clear-Com

Clear-Com Tempest2400 Manual de usuario

Clear-Com

Clear-Com MS-200C Guía de solución de problemas

Clear-Com

Clear-Com KB-111A Guía de solución de problemas

Clear-Com

Clear-Com SB-704 Manual de usuario

Clear-Com

Clear-Com Eclipse HX-Median Manual de usuario

Clear-Com

Clear-Com HMS-4X Guía de inicio rápido

Clear-Com

Clear-Com TEMPEST 2400 Manual de usuario

Clear-Com

Clear-Com TEMPEST 2400 Manual de usuario

Clear-Com

Clear-Com LQ-2W2 Manual de usuario

Clear-Com

Clear-Com ENCORE EF-701M Manual de usuario

Clear-Com

Clear-Com Tempest 2400 MasterBelt Manual de usuario

Clear-Com

Clear-Com HelixNet Partyline Manual de usuario

Clear-Com

Clear-Com RS-700 Series Manual de usuario

Clear-Com

Clear-Com FreeSpeak II Integra Manual de usuario

Clear-Com

Clear-Com HelixNet Partyline Manual de usuario

Clear-Com

Clear-Com RS-601 Manual de usuario

Clear-Com

Clear-Com ICS-102 Manual de usuario

Clear-Com

Clear-Com FreeSpeak II Manual de usuario

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

CyberData

CyberData 011211 series Manual

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario