Clarke CIR450C Manual de instalación y operación

OPERATING & MAINTENANCE

INSTRUCTIONS

GC0415

CORDLESS IMPACT WRENCH

MODEL NO: CIR450C

PART NO: 4500633

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Impact Wrench.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,

accessories and packaging should be sorted, taken to a recycling centre and

disposed of according to the laws governing Waste Electrical and Electronic

Equipment.

Through the purchase of this product, the customer is taking on the obligation

to deal with the WEEE in accordance with the WEEE regulations in relation to

the treatment, recycling & recovery and environmentally sound disposal of

the WEEE. In effect, this means that this product must not be disposed of with

general household waste. It must be disposed of according to the laws

governing Waste Electrical and Electronic Equipment (WEEE) at a recognised

disposal facility.

BATTERY DISPOSAL

Dispose of old batteries in accordance with local authority regulations. Do not

incinerate or crush, as this will increase the risk of explosion and

contamination. If the battery contents come into contact with skin or the eyes,

rinse with clean water for several minutes and seek medical advice

immediately afterwards.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - do not let children handle the wrench.

4. DO NOT use in damp or wet conditions. Keep the work area well lit. Do not

use where a risk of fire or explosion is present.

5. Although the impact wrench may be used outdoors, DO NOT leave it

exposed to the elements. Avoid direct sunlight, direct heat, rain/moisture

etc.

6. Always keep body and clothing dry. Never work in damp area without

adequate insulation against electric shock.

7. Do not fit the wrench to a stand or clamping device that may damage it.

GENERAL USE

1. 1.This product vibrates during use. Vibration may be harmful to your hands

or arms. Stop using the machine if discomfort, a tingling feeling or pain

occurs and seek medical advice before resuming use.

2. ALWAYS use ear defenders.

3. ALWAYS stay alert and use common sense - do not use this product when

you are tired or under the influence of alcohol or medication.

4. ALWAYS ensure that the socket is correctly installed before switching on.

5. ALWAYS only use sockets which are specified for impact wrench use.

6. ALWAYS ensure the workpiece is firmly secured leaving both hands free to

control the impact wrench.

7. ALWAYS store this product in a dry, secure place out of reach of children or

untrained users.

8. ALWAYS keep all equipment dry especially the battery & battery charger.

9. ALWAYS keep metal objects such as coins, keys, nails or other small metal

objects which could make a connection from one terminal to another,

away from the battery cartridge. A short circuit across the terminals could

cause sparks, burns or start a fire.

10. ALWAYS ensure the machine has stopped before putting it down after use.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

11. ALWAYS set the forward/reverse Switch-bar to neutral when changing bits

or when the machine is not required for immediate use. This will avoid

accidental starting.

12. ALWAYS check for any damage or any condition that could affect its

operation. Any damaged part should be properly repaired.

13. NEVER force or misuse the machine. It will do a better and safer job at the

rate for which it was designed.

14. NEVER use this product if it is defective / operating abnormally.

15. NEVER carry the machine with your finger on the trigger.

16. NEVER abuse the mains cable of the battery charger. Never yank the

cable to disconnect it from the socket. Keep the cable away from sharp

edges/hot surfaces.

17. NEVER over-reach. Keep proper footing and balance at all times.

18. NEVER use this product for any other purpose than that described in this

booklet.

19. NEVER carry out any alterations or modifications to this product.

20. NEVER attempt to wipe the machine clean with solvents. Wipe plastic parts

with a soft cloth, slightly dampened with soapy water.

21. NEVER attempt any repairs yourself. If you have a problem with this product

contact your local CLARKE dealer.

IMPACT WRENCH SAFETY INSTRUCTIONS

1. ALWAYS use the impact wrench in the manner and for the functions

described in these instructions.

2. ALWAYS ensure the machine is not moving with the switchbar in the centre

position when changing sockets etc. Use only Impact Wrench sockets....DO

NOT use standard sockets.

3. ALWAYS finish tightening wheel nuts or engine parts with a torque wrench

or suitable spanner to the correct torque as recommended by the vehicle

manufacturer.

4. ALWAYS avoid excessive use of the wrench. When tightening a nut or bolt,

never allow the wrench to impact more than 8 times - to avoid over

tightening - 3 to 4 impacts is normally sufficient.

5. ALWAYS use outdoor extension leads if working outdoors. Always use an

approved cable extension suitable for the power rating of the battery

charger (see specifications), the conductor size should also be at least the

same size or larger than that on the charger. When using a cable reel,

always unwind the cable completely.

Please keep these instructions in a safe place for future reference.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

This product is provided with a 13 amp, 230 volt (50Hz), BS 1363 plug, for

connection to a standard, domestic electrical supply. Should the plug need

changing at any time, ensure that a plug of identical specification is used.

The battery charger for this appliance is of double insulated design

No earth conductor is provided. The two wires in the mains lead should be

wired up in accordance with the following colour code:

Blue -- Neutral

Brown -- Live

Connect the BROWN coloured cord to the plug terminal marked a letter “L”

Connect the BLUE coloured cord to the plug terminal marked a letter “N”

If the battery charger for this appliance is fitted with a plug which is moulded

on to the electric cable (i.e. non-rewireable) please note:

1. The plug must be thrown away if it is cut from the electric cable. There is a

danger of electric shock if it is subsequently inserted into a socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace the fuse cover, ensure that the correct

replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from your local Clarke dealer

or most electrical stockists.

FUSE RATING

The fuse in the plug must be replaced with one of the same rating and this

replacement must be ASTA approved to BS1362.

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

repairs yourself.

CABLE EXTENSION

Do not use an extension longer than 10 metres and one where the

conductors, are less than 1.5mm2.

If used outdoors, ensure the extension cable is designed for outdoor use.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY SYMBOLS

The full technical specification of the battery charger is printed on a label on

the charger. The meanings of the markings and symbols are shown below.

COMPONENT INVENTORY

The CIR450 is a professional, cordless impact wrench which is rechargeable

using the mains power adaptor.

Upon receipt, unpack and lay out the components, checking against the

following list. Any damage or deficiency should be reported to your CLARKE

dealer immediately.

1. 24V Impact Wrench with 1.7 Ah battery pack

2. Battery-charging unit

3. Side handle

4. Moulded tool-case

Class II appliance which does not need an earth connection.

For indoor use only.

Read the manual before operating this product.

Falls under the Waste Electrical & Electronic Equipment directive

(WEEE).

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT IDENTIFICATION

1. 1/2” Square Socket Drive

2. Battery Release Button

3. Forward/Reverse Switch-bar

4. Battery Pack

5. Trigger

6. Wrist Strap

7. Hand Grip

NOTE: The CIR450C charger is not

compatible with the

earlier CIR450/450B

battery.

BATTERY CHARGING

1. The new battery pack will require

charging before use.

2. Squeeze the battery release buttons on

either side of the battery pack and pull

gently down to disengage the battery

pack from the machine as in Fig 1.

3. Plug the charger into a 230v (mains)

power supply and switch ON.

4. Insert the battery pack into the battery

charger, as shown in Fig 2, noting that it

will only fit one way.

• The green POWER ON light will

illuminate to show the unit is

connected to the mains supply.

5. Press the “SET” button and the green

light will turn off ,the RED charging light

will illuminate and charging will begin.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• If charging does not take place,

ensure all connections are clean

and free of grease etc.

• If the red charging light will not stay

on for more than a few moments,

the battery pack is likely to be

defective and it must be replaced

with a new one.

• When charging is complete

(typically after about 1/2 hour), the

RED charging light goes off and the

green light turns back on. The

battery pack can be considered

charged and be removed. The

charging time will be dependant

upon the initial state of the batteries.

• When charging a new battery pack it may initially not accept full

charge. This is common & does not indicate a fault. It can be

recharged fully after it has been discharged a couple of times.

6. After charging, switch off and unplug the charger from the power supply.

7. Remove the battery pack from the charger and slide it back into the

machine until it clips into place.

The battery pack should slide in easily.If the battery pack is not to be fitted

immediately, ensure that the metal contacts are protected so as to avoid the

possibility of a short circuit which would cause damage.

Remember to avoid extremes of heat or cold when charging. Avoid

temperatures outside the range of Minimum 4°C /Maximum 50°C. Avoid

placing batteries in direct strong sunlight or other heat source.

NOTE: Ni-Cad batteries as used in Clarke cordless power tools should be

given a full charge when first supplied new. Maximum battery

performance will be achieved after approximately 5 complete

charge/discharge cycles.

NOTE: The battery should be fully discharged before recharging in order

to achieve its optimum performance. Constant topping up after

only a small amount of charge has been used will, in effect,

reduce its capacity.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Nickel cadmium batteries will slowly lose their power whilst in storage. If they

become fully discharged, do not leave the batteries in this state for any length

of time.

OPERATION

1. Align the chosen socket and simply push it onto the anvil. Use only ½”

square drive impact sockets as listed on page 14.

2. Squeeze the trigger to start the machine. Release the trigger to stop.

3. To run the impact wrench in reverse, push

the switch-bar through the drive unit as

shown in Fig 3. The direction of rotation is

shown on the end face of the switch-bar.

• The 3-position switch bar controls forward

or reverse direction of rotation. Select the

appropriate position ONLY when the

machine is STATIONARY. Do not move the

switch-bar when the spindle is moving.

When the switch-bar is in the central

position the trigger is locked.

4. Always check the direction of rotation

before operation.

5. Turn off the machine as soon as the impact

sound is heard.

Note: As the battery becomes discharged, the

power available will drop. Operating the

machine at low speed will cause a reduction in torque.

6. After use, recharge the battery pack as shown on pages 8-9. Avoid leaving

your batteries in a discharged state.

LOOSENING A WHEEL NUT

1. Remove any wheel trim, before selecting the appropriate socket and

placing firmly on the square drive of the wrench.

2. With the FORWARD/NEUTRAL/REVERSE switchbar in the REVERSE running

position, and holding the wrench firmly in BOTH HANDS, pull the trigger. The

CAUTION: ALWAYS BE SURE THAT THE TOOL IS SWITCHED OFF BEFORE

ATTACHING OR REMOVING A SOCKET. ALWAYS TAKE CARE TO USE THE

CORRECT SIZE SOCKET FOR BOLTS AND NUTS. AN INCORRECT SOCKET

WILL CAUSE DAMAGE TO THE BOLT OR NUT.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

nut will be impacted repeatedly until it is loosened. IMPORTANT! Release

the trigger immediately the nut begins to loosen.

3. Jack up the vehicle according to the vehicle handbook so that the wheel

is clear of the ground, then proceed to fully undo the wheel nuts.

TIGHTENING A NUT

1. Start the nut by hand, ensuring it is not cross threaded, then with the

appropriate socket installed on the wrench, place it on the nut.

2. With the FORWARD/NEUTRAL/REVERSE switch-bar in the clockwise

(FORWARD) running position, and holding the wrench firmly in BOTH

HANDS, pull the trigger.

3. Run each nut up in turn until it is ‘nipped’ up only - do not tighten. When all

nuts are nipped up, tighten progressively by pulling the trigger fully and

allowing the action to operate for 3 to 4 impacts only to prevent

overtightening.

4. ALWAYS finish tightening with a torque wrench. The weight of the vehicle

will need to be placed on the wheel to prevent it from rotating while the

nuts are tightened. Ensure the final torque applied to the nuts meets the

vehicle manufacturer’s recommendations.

RECHARGING

Recharge the battery pack following each period of use as described on

pages 7-8.

1. Check that the red CHARGING light illuminates and remains on during the

charging process.

2. If the red CHARGING light goes out almost straight away after repeating

this procedure a couple of times, although the green POWER ON light is lit,

the battery pack should be replaced with a new one.

3. The charging light should remain on for about 1 hour, after which, the

battery cartridge may be removed and used.

4. After charging, remove the charger from the power supply.

5. For maximum battery life, we recommend that you maintain the battery in

a fully charged state at all times.

WARNING: ENSURE THAT THE CORRECT SOCKET IS BEING USED FOR THE

NUTS ON YOUR PARTICULAR VEHICLE. AN INCORRECT SOCKET SIZE IS

LIKELY TO DAMAGE THE HEADS OF THE BOLTS/NUTS.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Clarke

Clarke

Clarke CIR18LiC Manual de instalación y operación

Clarke

Clarke Woodworker CPT600 Manual de instalación y operación

Clarke

Clarke Woodworker CJS1-C Manual de instalación y operación

Clarke

Clarke CBTSR Manual de instrucciones

Clarke

Clarke CCRT266 Manual de instrucciones

Clarke

Clarke PRO236 Manual de instalación y operación

Clarke

Clarke Air CAT105 Manual de instrucciones

Clarke

Clarke CHT674 Manual de usuario

Clarke

Clarke CIR18Li Manual de instalación y operación

Clarke

Clarke CSB34 Manual de instrucciones

Clarke

Clarke CAT141 Manual de instalación y operación

Clarke

Clarke CONTRACTOR CON1450WC Guía de solución de problemas

Clarke

Clarke CHT141 Manual de usuario

Clarke

Clarke CMPS2 Manual de instrucciones

Clarke

Clarke Air 25C Manual de instalación y operación

Clarke

Clarke CAT209 Manual de instalación y operación

Clarke

Clarke Air CAT217 Manual de instalación y operación

Clarke

Clarke CHT259 Manual de instrucciones

Clarke

Clarke CAT126 Manual de instalación y operación

Clarke

Clarke Metalworker CDP350V Manual de instalación y operación

Clarke

Clarke CAT113 Guía de instalación

Clarke

Clarke CDP10B Manual de instrucciones

Clarke

Clarke CAT108 (1/2) Manual

Clarke

Clarke CPSB200 Manual de instrucciones

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual