Clarke CAT211 Manual de instalación y operación

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1019 - ISS 1

3PC AIR BLOW GUN KIT

MODEL NO: CAT211

PART NO: 3120528

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Blow Gun kit.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

SPECIFICATION

COMPRESSED AIR REQUIREMENTS

Use only clean, dry, regulated compressed air as a power source.

A build-up of moisture or oil in the air compressor will accelerate wear and

corrosion in the tool. Ensure any moisture is drained from the compressor daily

and the inlet filter is kept clean.

If an unusually long air hose is required, (over 8 metres), the line pressure or the

hose inside diameter may need to be increased.

The hose must be rated at 150% of the max operating pressure of the tool.

If an automatic in-line filter/regulator is used, it will keep the tool in good

condition, but should be regularly checked.

Never exceed the maximum operating pressure for the air tool. It is

recommended that air pressure to this tool does not exceed 90 psi. Higher

pressures and dirty air will shorten the life of the tool due to faster wear and is a

possible safety hazard

Max Operating Pressure 90 psi (6.2 bar)

Air Inlet Size 1/4“BSP Female

Air Consumption 9.5 cfm (max @90psi)

Dimensions Pocket Blow Gun - 97 x 20 x 29mm (0.057kg)

Short nozzle Blow Gun - 130 x 140 x 21mm (0.13kg)

Long nozzle Blow Gun - 240 x 17 x 87mm (0.085kg)

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

THE WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

USE OF AIR POWERED TOOLS

1. Stay alert and use common sense - do not operate this air tool when you

are tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using the air tool. Eye protectors must

provide protection from flying particles from the front and the side.

3. DO NOT use the blow gun when other persons or animals are nearby or

may be hit by flying debris caused by the blow gun.

4. DO NOT overreach - Keep proper footing and balance at all times.

5. Never use oxygen, CO2, combustible gasses or any type of bottled gas as

a source of power for this blow gun.

6. DO NOT connect the air supply hose with your finger on the trigger.

7. DO NOT exceed the maximum pressure for the air tool of 90 psi / 6.2 bar.

8. Keep the air supply hose away from heat, oil and sharp edges.

9. DO NOT fit the blow gun to a stand/clamping device that may damage it.

10. Check air hoses for leaks or worn condition before use and ensure that all

connections are secure.

11. Do not use the blow gun for any purpose than that described here.

12. DO NOT carry out any alterations or modifications to the blow gun.

13. Always disconnect from the air supply when performing any maintenance.

14. DO NOT use the blow gun if it is defective or operating abnormally.

15. Always maintain your blow gun with care.

16. DO NOT discharge this blow gun at any persons or animals.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

17. DO NOT insert into any part of yours or anyone else’s body.

18. DO NOT point directly at a person’s skin or at a fire.

19. DO NOT carry the blow gun by the hose or with your finger on the trigger.

20. When not in use the blow gun must be disconnected from the air supply

and stored in a dry place out of the reach of children.

21. DO NOT store the blow gun where the temperature is below 0oC.

CONNECTING /DISCONNECTING THE AIR SUPPLY

1. Connect a suitable hose to the air inlet.

2. Connect the other end of the air hose to the air compressor.

3. Turn on the air supply and check for air leaks. Rectify any found before

proceeding.

• PTFE tape may be useful for sealing threaded connections.

4. Your blow gun is now ready for use.

5. Set the compressed air pressure to suit at the compressed airline regulator.

6. DO NOT disconnect the air supply hose until the compressed air has been

isolated at a shut off valve. Once the pressure has been released,

disconnect the air supply hose.

MAINTENANCE

1. Before use, drain any condensate from the airline filter and compressor.

2. Clean thoroughly after use with a suitable solvent.

Please note that outside factors may affect the blow gun operation and

efficiency. These include reduced compressor output, excessive drain on the

airline, moisture or restrictions in the air-line, or the use of connectors of

improper size or poor condition which will reduce air supply.

Your CLARKE blow gun has been designed to give long and trouble free

service. If, however, having followed the instructions in this booklet carefully,

you encounter problems, take the product to your local CLARKE dealer.

WARNING: MAKE SURE THAT THE BLOW GUN IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

No Description No Description

1 Main Housing 8 Button

2 Spring 9 Nozzle

3O-ring 10Largering

4 Valve stem 11 Small ring

5O-ring 12Largering

6 O-ring 13 O-ring

7 Valve seat 14 Air inlet

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

No Description No Description

1 Main Housing 10 Valve stem

2 O-ring 11 O-ring

3 Connector 12 O-ring

4 O-ring 13 Small ring

5 Nozzle 14 Large ring

6 Nozzle sleeve 15 Trigger

7 Venturi tip 16 Pin

8 Spring 17 Air inlet

9 O-ring

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

No Description No Description

1 Main Housing 7 O-ring

2 Air inlet 8 O-ring

3 Spring 9 Valve seat

4 Valve stem 10 Trigger

5 O-ring 11 Pin

6 O-ring 12 Air nozzle

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Clarke

Clarke

Clarke Air 25C Manual de instalación y operación

Clarke

Clarke SB30 Manual de usuario

Clarke

Clarke Air CAT149 Manual de instalación y operación

Clarke

Clarke CAT108 (1/2) Manual

Clarke

Clarke Strong-arm AHP 16 Manual de instrucciones

Clarke

Clarke X-Pro CAT205 Manual de instalación y operación

Clarke

Clarke CIR450 Manual de instalación y operación

Clarke

Clarke CAT50 Manual de instalación y operación

Clarke

Clarke Air CAT232 Manual de instalación y operación

Clarke

Clarke STRONG-ARM CSA4B Manual de instrucciones

Clarke

Clarke CHG 1500B Manual de instalación y operación

Clarke

Clarke CBS16 Manual de instrucciones

Clarke

Clarke CE7 PRO Manual de usuario

Clarke

Clarke CHT259 Manual de instrucciones

Clarke

Clarke BJ300 Manual de usuario

Clarke

Clarke CSB10 Manual de instrucciones

Clarke

Clarke STRONG-ARM CSA10BB Manual de instrucciones

Clarke

Clarke CRT130 Manual de instrucciones

Clarke

Clarke Metalworker CDP202B Manual de instrucciones

Clarke

Clarke Metalworker CDP350V Manual de instalación y operación

Clarke

Clarke Air CAT105 Manual de instrucciones

Clarke

Clarke CMFTLi Manual de instrucciones

Clarke

Clarke METALWORKER CBS20 Manual de usuario

Clarke

Clarke X-Pro CAT199 Manual de instalación y operación

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual