Cisco Aironet 1810W Series Manual de usuario
GETTING STARTED GUIDE
Cisco Aironet 1810W Series Access Points
First Published: June 02, 2016
Last Modified: August 3, 2022
2
1About this Guide
2About the Access Point
3Safety Instructions
4Unpacking the AP
5Ports and Connectors on the AP
6Preparing the AP for Installation
7Installation Overview
8Performing a Pre-Installation Configuration
9Mounting the Access Point
10 Powering the Access Point
11 Configuring and Deploying the Access Point
12 Checking the Access Point LEDs
13 Miscellaneous Usage and Configuration Guidelines
14 Related Documentation
15 Declarations of Conformity and Regulatory Information
3
1 About this Guide
This guide provides instructions on how to install and configure your Cisco Aironet 1810W series
access points. This guide also provides mounting instructions and limited troubleshooting procedures.
The Aironet 1810W series access point is abbreviated as AP in this document.
2 About the Access Point
The Cisco Aironet 1810W series access point is an 802.11 a/b/g/n/ac (Wave 2) access point, with
internal antennas.
The Cisco Aironet 1810W has multiple mounting options to standard junction boxes. The AP can be
vertically mounted on a wall or on a desk/horizontal surface using the optional cradle kit. Physical
security is offered with the included Torx screw and the option to add a Kensington lock.
The AP supports 2.4 GHz 2x2 802.11 b/g/n MU-MIMO and 5 GHz 2x2 802.11 a/n/ac (Wave 2)
MU-MIMO applications simultaneously.
Access Point Features
The features of the 1810W series access points are:
•Supported mode(s) of operation:
–
Centralized
•Radio features supported are:
–
2.4 GHz and 5 GHz concurrent radios
–
2.4GHz radio with 2TX x 2RX and 2 spatial steams
–
5GHz radio with 2TX x 2RX and 2 spatial steams
–
802.11ac based Transmit Beamforming
–
Quality of Service (QoS)
–
Radio Resource Management (RRM)
–
Rogue Detection
–
BandSelect
–
Integrated Bluetooth LE 4.1 radio for location and asset tracking.
4
•The AP supports the following hardware external interfaces:
–
Three local GigE Ethernet Ports, one uplink GigE port, and one passive pass-through RJ45
port.
–
One 10/100/1000BASE-T PoE uplink port.
–
RS-232 management console interface through RJ-45.
Note The AP may face issues while booting if you use an unterminated console cable (not
plugged into any device or terminal) or a console cable that is more than one meter in
length.
–
Three 10/100/1000BASE-T ports (local Ethernet ports), one of which also serves as a PoE-Out
port.
The PoE-Out port provides 802.3af power when the AP is powered by Cisco local power
supply (AIR-PWR-D=) and ~6.5W power when the AP is powered by 802.3at power. The
PoE-Out port does not provide any power output when the AP is powered by 802.3af power.
–
DC power connector.
–
One RJ-45 passive pass-through port (back to bottom).
–
Mode button. For information on how to use the Mode button, see “Using the Mode Button”
section on page 36.
–
One multi-color LED status indicator for the AP status. LEDs are also present to indicate
per-port status for local the Ethernet ports. For information, see the “Checking the Access
Point LEDs” section on page 33.
–
Three local Gigabit Ethernet ports available to securely connect wired devices to the network.
•Two integrated 2.4 GHz/5 GHz dual-band antennas located on the sides of the 1810W access
point under the top housing. Peak antenna gain is approximately 2 dBi and 4 dBi in the 2.4 GHz
and 5 GHz bands respectively.
A full listing of the access point's features and specification are provided in the Cisco Aironet 1810W
Series Access Point Data Sheet, at the following URL:
http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1810w-series-access-points/datashe
et-c78-736869.html
5
Access Point Model Numbers and Regulatory Domains
The Cisco Aironet 1810W series access point comes in the model number format AIR-AP1810W-x-K9.
The ‘x’ in the model number is a placeholder for the regulatory domain. For information on supported
regulatory domains, see the following page:
http://www.cisco.com/go/aironet/compliance
6
3 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings
document that is shipped with your access point. The translated warnings are also in the Translated
Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury.
Before you work on any equipment, be aware of the hazards involved with electrical
circuitry and be familiar with standard practices for preventing accidents. Use the
statement number provided at the end of each warning to locate its translation in the
translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Read the installation instructions before you connect the system to its power source.
Statement 1004
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Warning
This product relies on the building’s installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than:
20A.
Statement 1005
Warning
Do not operate your wireless network device near unshielded blasting caps or in an
explosive environment unless the device has been modified to be especially qualified for
such use.
Statement 245B
Caution The fasteners you use to mount an access point on a ceiling must be capable of
maintaining a minimum pullout force of 20 lbs (9 kg) and must use a minimum of 4 holes
on the mounting bracket, or a minimum of 2 holes when mounting on a network box.
7
Caution This product and all interconnected equipment must be installed indoors within the same
building, including the associated LAN connections as defined by Environment A of the
IEEE 802.3af/at Standard.
Note The access point is suitable for use in environmental air space in accordance with section
300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the
Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power
injector in air handling spaces.
Note Use only with listed Information Technology Equipment (ITE) equipment. For more
information on ITE equipment, refer to article 645 of the latest National Electrical Code
(NEC).
8
4 Unpacking the AP
To unpack the access point, follow these steps:
Step 1 Unpack and remove the access point and the mounting accessories, from the shipping box.
Step 2 Return any packing material to the shipping container and save it for future use.
Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact
your Cisco representative or reseller for instructions.
–
The access point
–
Mounting bracket AIR-AP-BRACKET-W2=
–
Torx security screw and mylar label to cover the screw
The following accessories can be ordered separately from Cisco:
•Spacer kit AIR-AP1810W-KIT=, includes spacer and RJ-45 jumper cable.
•Cradle kit AIR-OEAP1810-CRD=, includes back cover and RJ-45 jumper cable.
•Cisco local power supply AIR-PWR-D=.
•Physical security kit AIR-SEC-50=, which includes 50 security screws used to secure the access
point onto the wall-mounting bracket, 50 RJ-45 block-out plugs and 2 unlock keys for blocking
physical access to the RJ45 Ethernet ports.
9
5 Ports and Connectors on the AP
Figure 1 Face of the AP
1
Location of the Status LED, along with ports
and connectors, on the base of the AP 2
Location of the 48V DC port on the left side
of the AP
354635
2
1
10
Figure 2 Base of the AP with the Ports and Connectors
Note A physical security kit AIR-SEC-50=, which is sold separately, includes RJ-45 block-out plugs
and two unlock keys using which you can restrict physical access to the Ethernet and console
1
Location of the concealed Status LED. You
can see the LED only when it lights up. 4
LAN port 3.
2
Console port.
The AP is shipped with an RJ-45 block-out
plug in this port. You can get an unlock key
for this by ordering physical security kit
AIR-SEC-50=. 5
LAN port 2.
3
Passive Pass-Through port.
It is an RJ-45 port, from the base of AP to the
back of the AP.
6
PSE / LAN port 1.
This port provides 802.3af/at Power
Sourcing Equipment (PSE) PoE-Out power
on the LAN 1 Ethernet interface. With
802.3at input the PoE-Out is 6.95W (Class
2).With DC input the PoE-Out is 12.95W
(Class 0).
354633
2 3 4 5 6
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Cisco
Cisco
Cisco Catalyst 9166I Series Manual de usuario
Cisco
Cisco Meraki MR70 Manual de usuario
Cisco
Cisco Aironet AIR-AP1252AG-A-K9 Manual
Cisco
Cisco AIR-BR1310G-A-K9-R - Aironet 1310 Outdoor Access... Manual de usuario
Cisco
Cisco Meraki MR53E Manual de usuario
Cisco
Cisco WAP121 Manual de instrucciones
Cisco
Cisco AIR-AP1251AG-A-k9 Manual
Cisco
Cisco MERAKI MR34 Manual de usuario
Cisco
Cisco Aironet 521 Manual de usuario
Cisco
Cisco WAP125 Manual de usuario
Cisco
Cisco 1130AG - Aironet - Wireless Access Point Manual
Cisco
Cisco Catalyst IW9167E Manual
Cisco
Cisco Aironet 1570 Series Guía
Cisco
Cisco MR18 Manual de usuario
Cisco
Cisco 1130AG - Aironet - Wireless Access Point Manual de usuario
Cisco
Cisco Meraki Go GR60 Manual de usuario
Cisco
Cisco Aironet 1300 Series Manual de usuario
Cisco
Cisco Catalyst 9166 Series Manual
Cisco
Cisco AIR-CAP3502I-A-K9 Manual de usuario
Cisco
Cisco Meraki MR56 Manual de usuario
