Cisco Nexus 5000 Series Manual de usuario
D Commands
•delay (interface), page 2
•description (interface), page 3
•duplex, page 5
Cisco Nexus 5000 Series Interfaces Command Reference
1
delay (interface)
To set a delay value for an interface, use the delay command. To restore the default delay value, use the no
form of this command.
delay tens-of-microseconds
no delay
Syntax Description Throughput delay in tens of microseconds. The range
is from 1 to 16,777,215.
tens-of-microseconds
Command Default 10 microseconds
Command Modes Interface configuration mode
Subinterface configuration mode
Command History ModificationRelease
This command was introduced.4.0(0)N1(1a)
Support for Layer 3 interfaces was added.5.0(3)N1(1)
Examples This example shows how to set a delay of 30,000 microseconds on an interface:
switch(config)# interface ethernet 1/1
switch(config-if)# delay 30000
switch(config-if)#
This example shows how to set a delay of 1000 microseconds on a subinterface:
switch(config)# interface ethernet 1/1.1
switch(config-subif)# delay 1000
switch(config-subif)#
Related Commands DescriptionCommand
Configures an Ethernet routed interface.interface ethernet (Layer 3)
Displays the interface configuration information.show interface
Cisco Nexus 5000 Series Interfaces Command Reference
2
D Commands
delay (interface)
description (interface)
To add a description to an interface configuration, use the description command. To remove the description,
use the no form of this command.
description description
no description
Syntax Description String description of the interface configuration. This
string is limited to 80 characters.
description
Command Default No description is added.
Command Modes Interface configuration mode
Subinterface configuration mode
Virtual Ethernet interface configuration
Command History ModificationRelease
This command was introduced.4.0(0)N1(1a)
Support for Layer 3 interfaces and virtual Ethernet interface was
added.
5.0(3)N1(1)
Support for virtual Ethernet interface was added.5.1(3)N1(1)
Usage Guidelines The description command is meant to provide a reminder in the configuration to describe what certain
interfaces are used for. The description appears in the output of the following commands such as show interface
and show running-config.
You can use this command on the following interfaces:
•Ethernet interface
•Management interface
•Subinterfaces
•Virtual Ethernet interface
Cisco Nexus 5000 Series Interfaces Command Reference
3
D Commands
description (interface)
Examples This example shows how to add a description for an interface:
switch# configure terminal
switch(config)# interface ethernet 1/1
switch(config-if)# description "10G Server Link"
switch(config-if)#
This example shows how to add a description for a virtual Ethernet interface:
switch# configure terminal
switch(config)# interface vethernet 1
switch(config-if)# description "Virtual interface"
switch(config-if)#
Related Commands DescriptionCommand
Displays the interface configuration information.show interface ethernet
Displays the virtual Ethernet interface configuration
information.
show interface vethernet
Displays the contents of the currently running
configuration file.
show running-config
Cisco Nexus 5000 Series Interfaces Command Reference
4
D Commands
description (interface)
duplex
To specify the duplex mode as full, half, or autonegotiate, use the duplex command. To return the system to
default mode, use the no form of this command.
duplex {full| half| auto}
no duplex {full| half| auto}
Syntax Description Specifies the duplex mode as full.full
Specifies the duplex mode as half.
This keyword is not supported on a
management interface.
Note
half
Specifies the duplex mode as autonegotiate.auto
Command Default None
Command Modes Interface configuration mode
network-adminvdc-admin
Command History ModificationRelease
This command was introduced.5.1(3)N1(1)
Usage Guidelines The interface speed that you specify can affect the duplex mode used for an interface, so you should set the
speed before setting the duplex mode. If you set the speed for autonegotiation, the duplex mode is automatically
set to be autonegotiated. If you specify 10- or 100-Mbps speed, the port is automatically configured to use
half-duplex mode, but you can specify full-duplex mode instead. Gigabit Ethernet is full duplex only. You
cannot change the duplex mode on Gigabit Ethernet ports or on a 10/100/1000-Mbps port that is set for Gigabit
Ethernet.
See the Cisco Nexus 5000 Series NX-OS Layer 2 Switching Configuration Guide for more information on
interface speed and duplex settings.
This command does not require a license.
Examples This example shows how to specify the duplex mode for full duplex:
switch#
configure
terminal switch(config)#
Cisco Nexus 5000 Series Interfaces Command Reference
5
D Commands
duplex
interface
ethernet 1/5 switch(config-if)#
duplex
full switch(config-if)#
Related Commands DescriptionCommand
Displays information about the interface, which
includes the duplex parameter.
show interface
Cisco Nexus 5000 Series Interfaces Command Reference
6
D Commands
duplex
Otros manuales para Nexus 5000 Series
14
Otros manuales de Cambiar de Cisco
Cisco
Cisco Nexus 5000 Series Manual de usuario
Cisco
Cisco Nexus 93180YC-FX Manual
Cisco
Cisco ME 3800X Manual de usuario
Cisco
Cisco Nexus 9808 Manual
Cisco
Cisco Nexus 7706 Manual
Cisco
Cisco CATALYST 5002 Manual de usuario
Cisco
Cisco DS-C9216I-K9 Manual de usuario
Cisco
Cisco Catalyst 2810 Series Manual de usuario
Cisco
Cisco WS-C4003 - Catalyst 4000 Chassis Switch Manual de usuario
Cisco
Cisco Catalyst 5000 Series Guía rápida
Cisco
Cisco 2975 - Catalyst LAN Base Switch Manual de usuario
Cisco
Cisco CSS 11801 Manual de usuario
Cisco
Cisco NM-16ESW - EtherSwitch Switch Manual de usuario
Cisco
Cisco MDS 9132T Guía de inicio rápido
Cisco
Cisco MDS 9396V Manual
Cisco
Cisco ME 3800X Manual de instalación
Cisco
Cisco Nexus 3400-S Manual
Cisco
Cisco SD208 Manual de usuario
Cisco
Cisco 2970 - Catalyst Switch Manual
Cisco
Cisco Cisco mds 9216 - fabric switch Manual
