Cisco 12000 GSR Series Manual de servicio

Course Reference Material

Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

NETg course 20614

form or by any means, electronic or mechanical, including photocopying, recording, broadcasting, or by any

information storage and retrieval system, without permission in writing from National Education Training

Group, Inc.

Skill Builder is a registered trademark of National Education Training Group, Inc. All other trademarks

referenced are the trademark, service mark, or registered trademark of their respective holders. National

Education Training Group, Inc. is not affiliated with any company or any other product or vendor mentioned

in this course and its accompanying materials.

The software and technology used to implement this course contain trade secrets that NETG considers to be

confidential and proprietary information, and your right to use this material is subject to the restrictions in the

license agreement under which you obtained it.

Contents

Objectives

Cisco 12000 Series GSR Routers

Cisco 12000 Router Installation

Cisco 12008 GSR

Cisco 12008 GSR: Installation

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

Cisco 12004 GSR

Cisco 12000 Series GSR Line Cards

Cisco 12000 Series GSR: Troubleshooting

Catalyst 3000 and 5000 Router Modules

Catalyst 3000 Router: Installation

Catalyst 5000 RSM: Installation

Catalyst 5000 RSM: Configuring

Procedures

Cisco 12000 Series GSR Routers

Cisco 12000 Router Installation

Cisco 12008 GSR: Installation

Catalyst 3000 and 5000 Router Modules

Catalyst 3000 Router: Installation

Catalyst 5000 RSM: Installation

Glossary

Alphabetical List of Terms

Objectives

Total number of objectives = 41

Note: (ULT) is the unit, lesson, topic ID.

Cisco 12000 Series GSR Routers

Major Components and Optional Modules

12000 Series Routers: Overview (ULT 112): Identify the 12000 series Gigabit Switch Routers (GSRs).• GRP (ULT 113): Identify the characteristics of the 12000 series Gigabit Route Processor (GRP).• Alarm Card (ULT 114): Identify the functions and features of the alarm card.• Switch Fabric (ULT 115): Identify the characteristics of the switch fabric.• Power Supplies (ULT 116): Identify the Cisco 12000 power supplies.• Blower Modules (ULT 117): Identify the features of the Cisco 12000 series cooling system.•

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

Cisco 12000 Router Installation

Preinstallation Guidelines (ULT 121): Identify preinstallation guidelines for the Cisco 12000 router.• AC−Input Power Supply: Installing (ULT 122): Sequence the steps involved in installing an AC−input

power supply.

•

DC−Input Power Supply: Installing (ULT 123): Sequence the steps involved in installing a DC−input

power supply.

•

System Startup (ULT 124): Sequence the steps involved in starting the Cisco 12012 system.• Installed Interfaces: Configuring (ULT 125): Identify the function of the setup command in configuring

installed interfaces.

•

Cisco 12008 GSR

Cisco 12008 GSR: Overview (ULT 131): Identify the characteristics of the Cisco 12008 Gigabit Switch

Router (GSR).

•

Power and Airflow Guidelines (ULT 132): Identify guidelines for power and airflow safety.• Cable Management System (ULT 133): Identify the functions and features of the cable management

system.

•

Cisco 12008 GSR: Installation

Upper Card Cage: Removing Cards (ULT 141): Identify the steps involved in removing cards from the

upper card cage.

•

Power Supply: Removing (ULT 142): Sequence the steps involved in removing a 12008 GSR power

supply.

•

CSC Alarm−Monitoring Facilities (ULT 143): Identify the functions of the Cisco Systems Capital (CSC)

alarm−monitoring facility.

•

Cisco 12004 GSR

Cisco 12004 GSR: Overview (ULT 151): Identify the characteristics of the Cisco 12004 Gigabit Switch

Router.

•

Power Supply and Fan Tray (ULT 152): Identify the characteristics of the Cisco 12004 GSR power supply

and fan tray.

•

Cable Management (ULT 153): Identify the characteristics of the Cisco GSR cable management system.• Maintenance Bus (ULT 154): Identify the features of the Cisco 12004 maintenance bus.•

Cisco 12000 Series GSR Line Cards

Quad OC−3c/STM−1c Line Card (ULT 161): Identify the characteristics of the Quad OC−3c/STM−1c POS

line card.

•

OC−12c/STM−4c POS Line Card (ULT 162): Identify the characteristics of the OC−12c/STM−4c POS line

card.

•

OC−12c/STM−4c ATM Line Card (ULT 163): Identify the characteristics of the OC−12c/ STM−4c ATM

line card.

•

Line Card Memory (ULT 164): Identify the characteristics of line card onboard memory for Cisco 12000

routers.

•

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

Cisco 12000 Series GSR: Troubleshooting

Startup Problems: Identifying (ULT 171): Identify Cisco 12000 Series Gigabit Switch Router (GSR) startup

problems.

•

Power Subsystem: Troubleshooting (ULT 172): Identify guidelines for troubleshooting the power

subsystem.

•

Processor Subsystem: Troubleshooting (ULT 173): Identify guidelines for troubleshooting the processor

subsystem.

•

Cooling Subsystem: Troubleshooting (ULT 174): Identify the guidelines for troubleshooting the 12000

series GSR cooling subsystem.

•

Cisco 12012: Running Diagnostics (ULT 175): Identify the steps involved in loading and running

diagnostics.

•

Catalyst 3000 and 5000 Router Modules

Catalyst 3000 Router: Installation

WS−X3011 Router Module: Overview (ULT 212): Identify the characteristics of the WS−X3011 router

module.

•

Router Card: Installing (ULT 213): Sequence the steps involved in connecting to the router console after

installing the router card.

•

Router Card: Network Connection (ULT 214): Identify the methods for connecting the router card to a

network.

•

Router Card: Configuring (ULT 215): Identify the steps involved in configuring the router card.•

Catalyst 5000 RSM: Installation

Catalyst 5000 Series Switch Architecture (ULT 221): Identify the characteristics of Catalyst 5000 series

switch architecture.

•

RSM: Installing (ULT 222): Identify the steps involved in installing the Route Switch Module (RSM).• RSM: Configuring for Inter−VLAN Routing (ULT 223): Identify guidelines for configuring the Route

Switch Module (RSM) for Inter−VLAN routing.

•

User Interface: RSM Command Modes (ULT 224): Identify each of the Route Switch Module (RSM)

command modes and their access methods.

•

Catalyst 5000 RSM: Configuring

Session Command: Using (ULT 231): Identify the functions of the session command.• RSM: Booting for the First Time (ULT 232): Identify the phases involved in booting the Route Switch

Module (RSM) for the first time.

•

RSM: Configuration Task List (ULT 233): Identify the different Route Switch Module (RSM)

configuration tasks for Inter−VLAN routing.

•

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

Procedures

Cisco 12000 Series GSR Routers

Cisco 12000 Router Installation

AC−Input Power Supply: Installing

Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets.• Verify that the power supply power switch is in the STANDBY position.• Slide the power supply into the vacant bay, using two hands to support it.• Tighten the captive screw on the power supply faceplate.• Check that the AC power cord shipped with the power supply is the correct type for your site.• Plug the AC power cord into the power supply AC receptacle.• Clip the spring clip over the power cord plug to secure the plug in place.• Connect the other end of the AC power cord to the source AC receptacle.• Check that the source AC circuit breaker servicing the source AC receptacle is switched on.• Repeat the previous steps for the rest of the AC−input power supplies.• Turn the power supply switch on.•

DC−Input Power Supply: Installing

Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets on the front edges

of the upper card cage.

•

Check that the DC−input power supply switch is turned OFF (O).• Remove the front cover of the power supply from the power supply faceplate.• Remove the DC power cable bracket from the power supply faceplate.• Thread the source DC power cable leads up underneath the power supply handle.• Remove the nut and locking washer from the power supply threaded terminals and attach the source DC

power cable lug to the terminals.

•

Thread the circuit breaker external alarm leads up through the handle and attach them to the circuit breaker

alarm terminal block.

•

Position the source DC power cable leads underneath the power supply handle on the power supply

faceplate.

•

Place the DC power cable bracket over the power cable leads and secure the cable leads and the cable

bracket to the power supply faceplate.

•

Verify that the source DC wiring from the source DC breaker to the power supply is correct.• Replace the power supply front cover on the power supply faceplate.• Slide the power supply into the power supply bay.• Turn the captive jackscrew on the power supply faceplate clockwise to seat the power supply into the

backplane power connector.

•

Turn on the source DC circuit breakers servicing each DC−input power supply.•

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

System Startup

Turn each system power switch to the ON position.• Check that the blower modules are operating by listening for them.• As the GRP boots, observe the GRP alphanumeric LED displays.• As the line cards boot, observe the alphanumeric LED indicators on each line card. Line cards boot from

left to right.

•

Boot the Cisco IOS software image you want to use by entering the appropriate b command at the ROM

monitor prompt (>).

•

Proceed with the setup facility or exit from setup and use configuration commands to configure global and

interface−specific parameters.

•

Cisco 12008 GSR: Installation

Upper Card Cage: Removing Cards

Attach an antistatic ESD wrist strap to your wrist.• Insert the banana jack into the ESD connection socket.• Write down each card type and card location.• Loosen the captive screws.• Pivot the two card ejector levers away from the faceplate to unseat the card.• Slide the card out of its slot.• Stack the removed card on an antistatic mat for ESD protection.•

Power Supply: Removing

Set the power to the off position.• Turn the captive screw on the power supply faceplate.• Pull the power supply unit halfway out of its bay.• Pull the power supply unit out completely.• Set the power supply unit aside in a safe place.•

Catalyst 3000 and 5000 Router Modules

Catalyst 3000 Router: Installation

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

Router Card: Installing

Connect the switch to a computer or other data terminal equipment (DTE) device.• Connect the EIA−232 cable to the console, the DB−9 connector, on the switch.• Use the console configuration default settings for communication with the switch.• Power up the switch.• At the Greeting screen, press Return to enter the switch Main menu.• Press Ctrl and R from the switch Main menu to access the router card command−line interface (CLI).•

Router Card: Configuring

Connect an auxiliary terminal to the auxiliary port on your switch.• Turn on the power switch.• The switch Greeting screen appears. To access the router card from the Main menu, you press Ctrl and R.• Select Configuration from the Main menu.• Select Router Configuration from the Configuration menu.• Enter the box and port numbers and press the Enter key.• Select the required option from the Router Configuration menu.•

Catalyst 5000 RSM: Installation

RSM: Installing

Connect an ASCII terminal to a computer running terminal emulation software to the console port on the

Catalyst switch.

•

Use a screwdriver to loosen the captive installation screws and remove the module filler plate or the

existing module from the slot that you want to use.

•

Guide the RSM into the slot, aligning the sides of the RSM with the guides in the slot.• While keeping the module oriented horizontally, carefully slide it into the slot until its front panel makes

contact with the ejector levers.

•

Simultaneously push the left lever and the right lever in to fully seat the module in the backplane connector.• Tighten the captive installation screws on the left and right sides of the module.• Check the status of the module.• After verifying that the RSM is operational, enter the session mod/num command at the Cat5k>prompt.•

Glossary

Alphabetical List of Terms

(DTE) Data Terminal Equipment

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

data terminal equipment. Device at the user end of a user−network interface that serves as a data source,

destination, or both. DTE connects to a data network through a DCE device (for example, a modem) and

typically uses clocking signals generated by the DCE. DTE includes such devices as computers, protocol

translators, and multiplexers.

10BaseT

10−Mbps baseband Ethernet specification using two pairs of twisted−pair cabling (Category 3, 4, or 5): one

pair for transmitting data and the other for receiving data. 10BaseT, which is part of the IEEE 802.3

specification, has a distance limit of approximately 328 feet (100 meters) per segment.

ASIC

Application Specific Integrated Circuit, a chip designed for a particular application. ASICs are built by

connecting existing circuit building blocks in new ways

ATM

Asynchronous Transfer Mode. International standard for cell relay in which multiple service types (such as

voice, video, or data) are conveyed in fixed−length (53−byte) cells. Fixed−length cells allow cell processing

to occur in hardware, thereby reducing transit delays. ATM is designed to take advantage of high−speed

transmission media such as E3, SONET, and T3.

Attachment Unit Interface (AUI)

attachment unit interface. IEEE 802.3 interface between an MAU and a NIC. The term AUI can also refer to

the rear panel port to which an AUI cable might attach. Also called transceiver cable.

AUI

Attachment Unit Interface

AWG

American Wire Gauge

Basic Rate Interface (BRI)

Basic Rate Interface. ISDN interface composed of two B channels and one D channel for circuit−switched

communication of voice, video, and data.

BNC

BNC coonector. Standard connector used to connect IEEE 802.3 10Base2 coaxial cable to an MAU.

BRI

Basic Rate Interface

BTU

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

British thermal unit

buffer

A temporary storage area, usually in RAM.

C.S.C

Cisco Systems Capital

cage

a piece of hardware into which cards are installed

CEF

Cisco express forwarding

Challenge Handshake Authentication Protocol (CHAP)

Challenge Handshake Authentication Protocol. Security feature supported on lines using PPP encapsulation

that prevents unauthorized access. CHAP does not itself prevent unauthorized access, it merely identifies the

remote end. The router or access server then determines whether that user is allowed access.

Channel Service Unit (CSU)

channel service unit. Digital interface device that connects end−user equipment to the local digital telephone

loop. Often referred to together with DSU, as CSU/DSU.

channelized

Channelized modules are modules that can be broken down into time slots.

chassis

a box that houses main electonic components

Command Line Interface (CLI)

command line interface. Interface that allows the user to interact with the operating system by entering

commands and optional arguments. The UNIX operating system and DOS provide CLIs.

Compressed Serial Link Internet Protocol (CSLIP)

Compressed Serial Link Internet Protocol. Extension of SLIP that, when appropriate, allows just header

information to be sent across a SLIP connection, reducing overhead and increasing packet throughput on SLIP

lines.

CRC

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

Cyclic redundancy check. Error−checking technique in which the frame recipient calculates a remainder by

dividing frame contents by a prime binary divisor and compares the calculated remainder to a value stored in

the frame by the sending node.

CSC

Clock and scheduler card

CSU

Channel Service Unit. Digital interface device that connects end−user equipment to the local digital telephone

loop. Often referred to together with DSU, as CSU/DSU.

CxBus

Cisco Extended Bus. Data bus for interface processors on Cisco 7000 series routers.

Data Circuit−terminating Equipment (DCE)

data circuit−terminating equipment (ITU−T expansion). Devices and connections of a communications

network that comprise the network end of the user−to−network interface. The DCE provides a physical

connection to the network, forwards traffic, and provides a clocking signal used to synchronize data

transmission between DCE and DTE devices. Modems and interface cards are examples of DCE.

Data Service Unit (DSU)

data service unit. Device used in digital transmission that adapts the physical interface on a DTE device to a

transmission facility such as T1 or E1. The DSU is also responsible for such functions as signal timing. Often

referred to together with CSU, as CSU/DSU.

DB−25 connector

A 25−pin connector used by parellel ports data bus connector

dBus

Diagnostic bus

dial−on−demand routing (DDR)

dial−on−demand routing. Technique whereby a router can automatically initiate and close a circuit−switched

session as transmitting stations demand. The router spoofs keepalives so that end stations treat the session as

active. DDR permits routing over ISDN or telephone lines using an external ISDN terminal adaptor or

modem.

DIMM

dual in−line memory module

DRAM

20614 Cisco Installing and Maintaining Routers Part 4: 12000 GSR Series and XS5032 Modules

Este manual sirve para los siguientes modelos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco 800 Series Manual de usuario

Cisco

Cisco RV016 - Small Business - 10/100 VPN Router Manual de instrucciones

Cisco

Cisco Cisco 881 Manual de usuario

Cisco

Cisco ASR 1000 Series Manual de usuario

Cisco

Cisco aironet 1240 Manual

Cisco

Cisco 1100-8P Manual

Cisco

Cisco 6000 series Manual de usuario

Cisco

Cisco NCS 560-4 Manual

Cisco

Cisco WRT350N Manual de usuario

Cisco

Cisco 1710 Manual de usuario

Cisco

Cisco Network Router Manual de usuario

Cisco

Cisco Catalyst 1900 Series Manual

Cisco

Cisco SOHO 91 Manual de usuario

Cisco

Cisco Linksys E-Series Guía de instalación

Cisco

Cisco 1600 series Manual

Cisco

Cisco EA-Series Manual de usuario

Cisco

Cisco Catalyst 2928 Manual de usuario

Cisco

Cisco Catalyst IR1800 Rugged Series Manual de usuario

Cisco

Cisco RV Series Manual de usuario

Cisco

Cisco 2811 Series Manual de instrucciones

Cisco

Cisco 1003 Manual de usuario

Cisco

Cisco ASR 1002 Manual de usuario

Cisco

Cisco NCS 540 Series Manual de instalación

Cisco

Cisco 1801 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario