Cisco 2811 Series Manual de instrucciones

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Installing and Upgrading Fans in Cisco 2811

Series Routers

This document describes how to install or upgrade fans that are located internally within a Cisco 2811

series integrated services router. You need to remove the cover from the router to install or remove any

of these items. The document contains the following sections:

•Safety Warnings, page 1

•Removing the Chassis Cover, page 2

•Locating the Fan, page 5

•Installing and Removing the Fans, page 5

•Installing the Chassis Cover, page 13

Before you begin the fan replacement procedure, disconnect the power and remove the cover, as

described in the “Removing the Chassis Cover” section on page 2. After you complete the fan

replacement procedure, install the chassis cover as described in the “Installing the Chassis Cover”

section on page 13.

Safety Warnings

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Statement 1

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Removing the Chassis Cover

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning

Read the installation instructions before connecting the system to the power source.

Statement 1004

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings,

necklaces, and watches). Metal objects will heat up when connected to power and ground and can

cause serious burns or weld the metal object to the terminals.

Statement 43

Warning

Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF

or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,

detach the end away from the unit first.

Statement 1026

Removing the Chassis Cover

Cisco 2811 series routers have a cover that lifts off after you slide it free from front panel.

Caution Do not, under any circumstances, tamper with or attempt to remove the safety shields protecting the

WIC/HWIC slots and connectors on the Cisco 2811 routers.

Removing the Cover from Cisco 2811 Routers

To remove the chassis cover for a Cisco 2811 series router, follow these steps. You will need a number

2 Phillips screwdriver and a flat-blade screwdriver with a blade width of 1/4 ± 1/32 inch (5 to 7 mm).

Rack-mounted routers must be removed from the rack and positioned on a flat surface before you start

removing the cover.

Caution To prevent damage to the chassis, follow this procedure to remove the cover. Do not pry on the plastic

bezel or on the ears at either side of the chassis on the back.

The following warning applies only if the router is provided with a DC power input:

Warning

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Statement 1003

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Removing the Chassis Cover

Step 1 Make sure that the router is turned off and disconnected from its power source.

Warning

Before opening the unit, disconnect the telephone-network cables to avoid contact with

telephone-network voltages.

Statement 1041

Step 2 If rack-mounting brackets are attached to the chassis, remove them, using a Phillips screwdriver.

Step 3 Remove the four screws at the back of the top cover, using a Phillips screwdriver.

Step 4 Perform the following steps to loosen the cover from the chassis:

a. Insert the blade of the 1/4-inch screwdriver straight into the square hole on either side of the chassis

near the back, so that it fits against the chassis and does not go past the chassis and into the narrow

slot. See Figure 1.

Caution Make sure that the tip of the screwdriver does not slide into the narrow vertical slot that is visible inside

the square hole. The tip of the screwdriver should rest on the metal tab just inside the chassis cover and

to the right of the vertical slot.

Figure 1 Inserting the Screwdriver into the Side of the Chassis

b. With the screwdriver positioned as required in Step a. above, rotate the screwdriver a quarter turn

toward the back of the chassis to loosen one side of the cover. See Figure 2.

Caution The friction fit may be fairly tight; however, if the cover does not move with moderate effort, make sure

that the screwdriver is not inserted into the narrow vertical slot.

Figure 2 Rotating the Screwdriver to Loosen the Chassis Cover

c. Repeat Step a. and Step b. for the opposite side of the chassis.

103860

Screwdriver must not

enter the vertical slot

103861

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Removing the Chassis Cover

The cover should now be positioned back from the bezel about 1/4 inch (6 to 7 mm). If it is not, repeat

Step a. and Step b. for one or both sides of the chassis.

Step 5 Slide the cover toward the back of the chassis until it contacts a stop (about 1 inch [25 mm]). The front

edge of the cover should be free. See Figure 3.

Note After the cover is loosened as in Step 4, there may still be some friction to overcome as you

complete the removal. However, do not use the screwdriver again as in Step 4.

Step 6 Lift the cover free of the router chassis.

Figure 3 Cisco 2811 Router—Cover in Position for Removal

103477

Plastic bezel

Approx. 1 inch

(25 mm)

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Locating the Fan

Figure 4 shows the locations of the fans in a Cisco 2811 series router.

Figure 4 Fan Locations in Cisco 2811 Routers

Note The fan numbers in Figure 4 correllate to IOS show environment command numbers. The arrows

show proper air flow.

Installing and Removing the Fans

The router fans rest on the chassis base and have a wire that connects to the system board.

Before you remove or install a fan, remove the chassis cover as described in the “Removing the Chassis

Cover” section on page 2.

Caution When you remove or install a fan, always wear an ESD-preventive wrist strap, and ensure that it makes

good contact with your skin. Connect the equipment end of the wrist strap to the metal part of the chassis.

1System fan 2System fan

3Power supply fan

271118

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Installing and Removing the Fans

Removing the System Fans

To remove a system fan, perform the following procedure. To complete this procedure, you may need a

flat-blade screwdriver.

Step 1 Locate the fans to be removed. See Figure 4 for the location of the fans.

Step 2 Disconnect the fan connector from the system board as shown in Figure 5.

Figure 5 Disconnecting the System Fan Connector from the System Board

Step 3 Remove the fan wire from the wire management clip, which is located on the chassis base as shown in

Figure 6.

Figure 6 Removing the Fan Wire from the Wire Management Clip

Step 4 Remove the fan by sliding it upward, and then tilting it toward the chassis wall as shown in Figure 8.

Note If the fan is difficult to grasp when sliding upward, use a flat-blade driver for leverage as shown

in Figure 7.

170494

170495

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Installing and Removing the Fans

Figure 7 Using a Flat-Blade Screwdriver for Added Leverage When Removing the Fan

Figure 8 shows the fan being tilted away from the chassis to remove it.

Figure 8 Lifting and Tilting the Fan to Remove

Step 5 Place the fan in an antistatic bag to protect it from ESD damage.

170531

1Lift the fan upward 2Tilt the fan toward chassis

170498

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Installing and Removing the Fans

Removing the Power Supply Fan

To remove the power supply fan, perform the following procedure. To complete this procedure, you may

need a flat-blade screwdriver.

Step 1 Locate the fan to be removed. See Figure 4 for the location of the fans.

Step 2 Disconnect the fan connector from the system board as shown in Figure 9.

Figure 9 Disconnecting the Power Supply Fan Connector

Step 3 Lift the ribbon cable to allow slack to remove the air baffle as shown in Figure 10.

Note It is not necessary to disconnect the ribbon cable from the CompactFlash printed circuit board

(PCB) or system board.

170510

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Installing and Removing the Fans

Figure 10 Lifting the Ribbon Cable

Step 4 Remove the plastic air baffle by gently squeezing the air baffle sides, disengaging the baffle from the

chassis base as shown in Figure 11.

Figure 11 Removing the Air Baffle

Step 5 Remove the fan wire from the wire management clip, which is located on the chassis base as shown in

Figure 6.

Step 6 Remove the fan by placing a flat-blade screwdriver at the base of the plastic fan housing and lifting the

fan in a vertical position, as shown in Figure 12.

170511170512

Installing and Upgrading Fans in Cisco 2811 Series Routers

78-17850-01

Installing and Removing the Fans

Figure 12 Using a Flat-Blade Screwdriver to Lift the Fan

Step 7 Disengage the fan from the side attachment slots and push the fan toward the center of the chassis, and

remove the fan as shown in Figure 13.

Figure 13 Disengaging the Fan from the Side Attachment Slots

Step 8 Place the fan in an antistatic bag to protect it from ESD damage.

170513

170530

Otros manuales para 2811 Series

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco CRS Manual de usuario

Cisco

Cisco 3825 Series Manual de servicio

Cisco

Cisco CISCO871-K9 - 871 Integrated Services Router Manual

Cisco

Cisco 7206 - VXR Router Manual de usuario

Cisco

Cisco RV340 Series Manual de usuario

Cisco

Cisco CCNA 2 Manual de usuario

Cisco

Cisco 7600 Series Instrucciones de montaje

Cisco

Cisco 1601-R Manual de usuario

Cisco

Cisco Linksys X2000 Manual de usuario

Cisco

Cisco NCS 4216 Manual de instrucciones

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Manual de usuario

Cisco

Cisco 8201 Manual de usuario

Cisco

Cisco ASR 1004 Guía de instalación

Cisco

Cisco NCS 5500 Series Manual de instrucciones

Cisco

Cisco NCS 560-4 Manual

Cisco

Cisco RV130 Manual de usuario

Cisco

Cisco CRS-1 - Carrier Routing System Router Manual de usuario

Cisco

Cisco 805 Series Manual de usuario

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Manual

Cisco

Cisco ASR 9001 Manual de usuario

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Manual de usuario

Cisco

Cisco 7606-S Manual de usuario

Cisco

Cisco 3600 Series Manual de usuario

Cisco

Cisco Small Business RV320 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario