Cisco WAE-674-K9 - Wide Area Application Engine... Manual de usuario

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Installing the Cisco WAE Inline Network Adapter

Product Number: WAE-INLN-4CG=

Models: FE-511-K9, WAE-511-K9, WAE-611-K9, WAE-512-K9, WAE-612-K9, WAE-7326-K9, WAE-7341-K9,

WAE-7371-K9, WAE-674-K9

This document describes how to install the Cisco WAE inline network adapter in your edge or core WAE

appliance. These instructions are intended for experienced technicians.

Note The Cisco WAE inline network adapter is not supported in a Central Manager appliance. (For more

information, see the “Important Operational Notes” section on page 7.)

Contents

This document contains the following sections:

•Product Overview

•Safety Guidelines

•Important Operational Notes

•Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances

•Installing Adapters in the WAE-512 and WAE-612 Appliances

•Installing Adapters in the WAE-7326 Appliance

•Installing Adapters in the WAE-7371, WAE-7341, and WAE-674 Appliances

•Cabling

•Related Documentation

•Obtaining Documentation, Obtaining Support, and Security Guidelines

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Product Overview

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Product Overview

This section contains the following topics:

•Inline Network Adapter Description

•Ports and LED Indicators

•Adapter Specifications

Note The minimum software release required for the inline network adapter is WAAS 4.0.7.

Inline Network Adapter Description

WAAS software versions prior to 4.2.1 support one optional 4-port Ethernet inline network adapter on

WAE-7341/WAE-7371/WAE-674 appliances. Up to two inline network adapters are supported using

WAAS software version 4.2.1 or later.

The inline network adapter is a full-height, three-quarter-length PCI-X network interface card that

contains four independent Gigabit Ethernet ports. (See Figure 1.)

Figure 1 Inline Network Adapter

159701

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Product Overview

The Cisco WAE inline network adapter provides an inline traffic interception capability for your

appliance. When you configure the WAE appliance for inline interception mode, you can set attributes

to control which interfaces are to be used over which VLANs. By default, the adapter operates on all

inline-capable interfaces and VLANs. You can configure the inline redirection feature using the WAAS

4.0.7 CLI or the WAAS 4.0.7 Central Manager GUI.

The WAAS software defines two new interface types: A group interface that represents an inline pair

grouping and a port interface that represents the individual port. These interfaces are referred to as

inlineGroup and inlinePort.

InlineGroup interfaces are numbered using the format slot/group. The slot number is the slot in which

the adapter is inserted. (In the WAE 500 series and 600 series appliances, you must install the adapter in

slot 1 only.) The group number is either 0 or 1 (each adapter has 2 group pairs). The group number is

displayed on the adapter label.

InlinePort interfaces are numbered slot/group/lan or slot/group/wan. The last attribute is the LAN or

WAN designator.

The inline network adapter also includes an onboard programmable watch dog timer (WDT) controller

that allows you to set the time to wait after a failure event, such as a power outage or a kernel crash,

before the unit begins to operate in mechanical bypass mode. In mechanical bypass mode, traffic is

bridged between the LAN and WAN ports of each group. Mechanical bypass mode prevents the WAE

from becoming a single point of failure and allows traffic to continue to flow between the router and the

client while it passes through an unresponsive WAE without being processed.

For more information about configuring the inline network adapter, see the Cisco Wide Area Application

Services Configuration Guide.

Ports and LED Indicators

Figure 2 shows the inline network adapter port numbers, interface designations, and LEDs.

Figure 2 Inline Network Adapter Port Numbering and LEDs

The inline network adapter has three LEDs that correspond to each port (the W1 LEDs correspond to

Port W1, and so forth). Table 1 describes the LEDs.

W1 Port WAN1; Group 1 WAN interface L1 Port LAN1; Group 1 LAN interface

W0 Port WAN0; Group 0 WAN interface L0 Port LAN0: Group 0 LAN interface

W1 L1 W0 L0

LINK/ACT

100

1000 BYPASS

W1 L1 W0 L0

272072

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Product Overview

Note On older inline network adapters, the LEDs are labelled 0, 1, 2, and 3. These correspond to W1, L1, W0,

and L0 respectively.

Adapter Specifications

Table 2 describes the inline network adapter technical and general specifications.

Table 1 Inline Network Adapter LEDs

LEDs State Description

Link / Activity On The 10/100/1000BASE-T interface is receiving power.

Blinking The Ethernet link is transmitting data.

100 On The speed of the Ethernet connection is 100BASE-TX.

1000 On The speed of the Ethernet connection is 1000BASE-TX.

Bypass Both the 100 and

1000 LEDs are on

The corresponding ports are in mechanical bypass mode.

Table 2 Inline Network Adapter Specifications

Specification Description

Copper Gigabit Ethernet Specifications

IEEE standard Gigabit Ethernet, 1000BASE-T

Fast Ethernet, 100BASE-T

Ethernet, 10BASE-T

Full duplex and half duplex Supports both half-duplex and full-duplex operation in all

operating speeds

Autonegotiation Autonegotiates between full-duplex and half-duplex operations

and between 1000-Mbps, 100-Mbps, and 10-Mbps speeds

Data transfer rate 1000-Mbps, 100-Mbps, and 10-Mbps speeds per port in

half-duplex mode

2000-Mbps, 200-Mbps, and 20-Mbps speeds per port in

full-duplex mode

General Technical Specifications

Interface standard PCI v2.2 32/64 bit, 33/66 MHz

PCI-X v1.0 32/64 bit, 66/100/133 MHz

Size 6.6 x 4.2 in. (167.64 x 106.68 mm)

PCI connector Universal 64-bit connector

PCI voltage +12 V (minimum 11.4 V, maximum 12.6 V)

+3.3 V (minimum 3.0 V, maximum 3.6 V)

Weight 6.18 oz (175 grams)

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Safety Guidelines

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the

following precautions:

•Warnings

•General Precautions

•Protecting Against Electrostatic Discharge

Warnings

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Warning

The safety cover is an integral part of the product. Do not operate the unit without the safety cover

installed. Operating the unit without the cover in place will invalidate the safety approvals and pose

a risk of fire and electrical hazards.

Statement 117

Warning

Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous

voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might

disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate

the system unless all cards and faceplates are in place.

Statement 156

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be

accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Operating humidity 0 to 90%, noncondensing

Operating temperature 32 to –122oF (0 to 50oC)

Storage temperature –4 to –149oF (–20 to –65oC)

Table 2 Inline Network Adapter Specifications

Specification Description

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Safety Guidelines

General Precautions

Observe the following general precautions for using and working with your system:

•Observe and follow service markings. Do not service any Cisco product except as explained in your

system documentation. Opening or removing covers that are marked with the triangular symbol with

a lightning bolt may expose you to electrical shock. Components inside these compartments should

be serviced only by an authorized service technician.

•If any of the following conditions occur, unplug the product from the electrical outlet and replace

the part or contact your authorized service provider:

–

The power cable or plug is damaged.

–

An object has fallen into the product.

–

The product has been exposed to water.

–

The product has been dropped or damaged.

–

The product does not operate correctly when you follow the operating instructions.

•Keep your system components away from radiators and heat sources. Also, do not block cooling

vents.

•Do not spill food or liquids on your system components, and never operate the product in a wet

environment.

•Do not push any objects into the openings of your system components. Doing so can cause fire or

electric shock by shorting out interior components.

•Use the product only with other Cisco-approved equipment.

•Allow the product to cool before removing covers or touching internal components.

•Use the correct external power source. Operate the product only from the type of power source

indicated on the electrical ratings label. If you are not sure of the type of power source required,

consult your service representative or local power company.

•Use only approved power cables. If you have not been provided with a power cable for your

Content Engine or for any AC-powered option intended for your system, purchase a power cable that

is approved for use in your country. The power cable must be rated for the product and for the

voltage and current marked on the product’s electrical ratings label. The voltage and current rating

of the cable should be greater than the ratings marked on the product.

•To help prevent electric shock, plug the system components and peripheral power cables into

properly grounded electrical outlets. These cables are equipped with three-prong plugs to help

ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable.

•Do not use appliance or voltage converters or kits sold for appliances with your product.

•To help protect your system components from sudden, transient increases and decreases in electrical

power, use a surge suppressor or line conditioner.

•Position cables and power cords carefully; route cables and the power cord and plug so that they

cannot be stepped on or tripped over. Be sure that nothing rests on your system components’ cables

or power cord.

•Do not modify power cables or plugs. Consult a licensed electrician or your power company for site

modifications. Always follow your local or national wiring rules.

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Important Operational Notes

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside your system. To prevent static damage, discharge

static electricity from your body before you touch any of your system’s electronic components. You can

do so by touching an unpainted metal surface on the chassis.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

•Limit your movement. Movement can cause static electricity to build up around you.

•When transporting a sensitive component, first place it in an antistatic container or packaging.

•Just before unwrapping the antistatic packaging, be sure to discharge static electricity from your

body by touching it to an unpainted metal part of the system unit for at least 2 seconds.

•Remove the adapter from its packaging and install it directly into your system unit without setting

it down. If it is necessary to set the adapter down, place it in its static-protective package. Do not

place the adapter on your system unit cover or on a metal table.

•Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and

workbench pads.

•Handle the adapter carefully, holding it by its edges or its frame.

•Do not touch solder joints, pins, or exposed printed circuitry.

•Do not leave the adapter where others can handle and possibly damage the adapter.

•Take additional care when handling adapters during cold weather because heating reduces indoor

humidity and increases static electricity.

Important Operational Notes

If you intend to reconfigure an edge or core WAE with a Cisco WAE inline network adapter installed in

it as a Central Manager device, first remove the inline network adapter. The inline network adapter is not

supported in a Central Manager appliance.

Installing Adapters in the FE-511, WAE-511, and WAE-611

Appliances

This section describes how to install the inline network adapter in the FE-511, WAE-511, and the

WAE-611 appliances. This section includes the following procedures:

•Removing the Cover

•Installing an Inline Network Adapter

•Completing the Installation

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances

Removing the Cover

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Statement 1

To remove the cover, follow these steps:

Step 1 Review the information in the “Safety Guidelines” section on page 5.

Step 2 Power down the appliance and all attached devices. Disconnect the power cord and all external cables.

Step 3 Loosen the two captive screws (labeled 1 in Figure 3) on the rear of the cover.

Figure 3 Removing the Cover

Step 4 Slide the cover back, and then lift it up and off the appliance.

Caution For proper cooling and airflow, replace the cover before turning on the appliance. Operating the

appliance for extended periods (over 30 minutes) with the cover removed might damage appliance

components.

115802

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances

Installing an Inline Network Adapter

Before you install an adapter, review the following information:

•The adapter slots are on the riser card assembly. You must first remove the riser card assembly to

access the adapter slots. (See Figure 4.)

•The appliance has two Peripheral Component Interconnect-Extended (PCI-X) adapter slots:

–

PCI-X slot 1 is for one full-height three-quarter-length adapter.

–

PCI-X slot 2 is for one low-profile half-length adapter; however, it is not used in this appliance.

•You must install the inline network adapter in PCI-X slot 1. (This slot is labeled “PCI 1” on the back

of the appliance.)

Caution When you handle static-sensitive adapters and appliances, take precautions to avoid damage from static

electricity. For details on handling these devices, see the “Protecting Against Electrostatic Discharge”

section on page 7.

Note The illustrations in this document might differ slightly from your hardware.

To install an inline network adapter, follow these steps:

Step 1 Review the safety information in the “Safety Guidelines” section on page 5.

Step 2 Power down the appliance and peripheral devices.

Step 3 Disconnect the power cord and then all external cables from the appliance.

Step 4 Remove the appliance cover.

Note You may find it easier to route the cables before you install the adapter.

Step 5 Loosen the captive screw (labeled 3 in Figure 4) located on the rear of the appliance adjacent to PCI-X

slot 1 and remove the expansion slot cover.

Note You must install PCI expansion slot covers on all vacant slots so that you can maintain the

electronic emissions characteristics of the appliance and ensure proper cooling of internal

components.

Installing the Cisco WAE Inline Network Adapter

OL-12480-03

Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances

Figure 4 Removing the Expansion Slot Cover

Step 6 Remove the riser card (labeled 1 in Figure 5) from the system board to access the expansion slot.

1Expansion slot cover (slot 2) 2Expansion slot cover (slot 1)

3Captive screw 4Riser card assembly

2 4

124478

Otros manuales para WAE-674-K9 - Wide Area Application Engine...

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Tarjeta de red de Cisco

Cisco

Cisco Linksys PLS300 Manual de usuario

Cisco

Cisco uBR-MC28U Manual de usuario

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manual de instalación y operación

Cisco

Cisco uBR-E-16U Manual de usuario

Cisco

Cisco 7304 Series Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco Valet Connector AM10 Manual de usuario

Cisco

Cisco EHWIC 1 GE-SFP-CU Manual de usuario

Cisco

Cisco uBR10-MC5X20H Manual de usuario

Cisco

Cisco VWIC-2MFT-T1 - Multiflex Trunk Voice/WAN Interface Card Expansion... Manual de usuario

Cisco

Cisco LINKSYS PLTS200 Manual de usuario

Cisco

Cisco Linksys WUSB600N Manual de usuario

Cisco

Cisco ONS 15310-MA Manual de usuario

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco PA-T3 Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco Gigabit Switch Router Cisco 12012 Guía

Cisco

Cisco WPC600N - Ultra RangePlus Wireless-N PC Card Manual de usuario

Cisco

Cisco Aironet 340 Series Manual de usuario

Cisco

Cisco LINKSYS WUSB54GR Manual de usuario

Cisco

Cisco HWIC-4ESW - EtherSwitch HWIC Switch Manual de usuario

Cisco

Cisco Gateway Controllers Instrucciones originales

Cisco

Cisco NPE-175 Manual del operador

Cisco

Cisco CE-100T-8 Manual de instrucciones

Cisco

Cisco PA-FE-FX Manual del operador

Cisco

Cisco Linksys WUSB54G Manual de usuario

Manuales populares de Tarjeta de red de otras marcas

FirstComm

FirstComm OBiWiFi5G Manual de usuario

Sun Microsystems

Sun Microsystems Interface Adapter Manual de usuario

TRENDnet

TRENDnet TU2-ETG Manual de usuario

YASKAWA

YASKAWA SI-EN3 Manual de usuario

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manual de usuario

Belkin

Belkin F5D7050 Manual de usuario

3Com

3Com EtherLink 3C509B Manual de usuario

TRENDnet

TRENDnet TEG-PCITX Manual de usuario

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manual de usuario

TwinMOS

TwinMOS Booming Manual de usuario

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manual de usuario

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manual de usuario

National Instruments

National Instruments NI 9234 Manual de usuario

Hama

Hama 49276 Manual de usuario

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manual de operación

Compaq

Compaq Wireless LAN 100 Manual de usuario

Bose

Bose PowerMatch Dante Manual de usuario

TRENDnet

TRENDnet TEG-PCITXR Manual de usuario