Cisco Firepower 9300 Manual

Cisco Firepower 9300 Hardware Installation Guide

First Published: 2015-07-16

Last Modified: 2018-11-14

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.

Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com

go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any

other company. (1721R)

CONTENTS

Overview 1

CHAPTER 1

Features 1

Chassis Components 4

Deployment Options 5

Package Contents 6

Serial Number Location 7

Front Panel 8

Rear Panel 9

Supervisor 10

Security Modules 12

Network Modules 14

10-G Network Module 14

40-G Network Module 15

100-G Network Module (Two Ports Single Wide) 16

100-G Network Module (Four Ports Single Wide) 17

100-G Network Module (Double Wide) 18

Hardware Bypass Network Modules 19

40-G Network Module with Hardware Bypass 20

10-G SR/10-G LR Network Module with Hardware Bypass 22

Power Supply Modules 24

Fan Modules 26

Supported SFP/SFP+ and QSFP Transceivers 26

Hardware Specifications 29

Product ID Numbers 30

Power Cord Specifications 33

Cisco Firepower 9300 Hardware Installation Guide

iii

Installation Preparation 39

CHAPTER 2

Installation Warnings 39

Safety Recommendations 41

Maintain Safety with Electricity 42

Prevent ESD Damage 42

Site Environment 43

Site Considerations 43

Power Supply Considerations 43

Rack Configuration Considerations 44

Mount and Connect 45

CHAPTER 3

Unpack and Inspect the Chassis 45

Rack-Mount the Chassis 46

Ground the Chassis 50

Install the FIPS Opacity Shield 52

Connect Cables, Turn on Power, and Verify Connectivity 56

Maintenance and Upgrade 59

CHAPTER 4

Remove and Replace the Supervisor 59

Remove and Replace the Security Module 60

Remove and Replace the SSD 61

Remove and Replace the Single-Wide Network Module 63

Remove and Replace the Double-Wide Network Module 66

Remove and Replace the Power Supply Module 69

Connect the DC Power Supply Module 71

Connect the HVDC Power Supply Module 72

Remove and Replace the Fan Module 74

Cisco Firepower 9300 Hardware Installation Guide

Contents

CHAPTER 1

Overview

•Features , on page 1

•Chassis Components, on page 4

•Deployment Options, on page 5

•Package Contents, on page 6

•Serial Number Location, on page 7

•Front Panel, on page 8

•Rear Panel, on page 9

•Supervisor, on page 10

•Security Modules, on page 12

•Network Modules, on page 14

•Hardware Bypass Network Modules, on page 19

•Power Supply Modules, on page 24

•Fan Modules, on page 26

•Supported SFP/SFP+ and QSFP Transceivers, on page 26

•Hardware Specifications, on page 29

•Product ID Numbers, on page 30

•Power Cord Specifications, on page 33

Features

The Cisco Firepower 9300 security appliance is a next generation network and content security platform. Its

modular standalone chassis offers high-performance and flexible I/O options, which enable it to run multiple

security services simultaneously. See Product ID Numbers, on page 30 for a list of the product IDs (PIDs)

associated with the Firepower 9300.

The Firepower 9300 supports the following software:

• Cisco Firepower Threat Defense

• Cisco Firepower eXtensible Operating System (FXOS)

• Cisco ASA

Cisco Firepower 9300 Hardware Installation Guide

The Firepower 9300 is certified for Common Criteria (CC) and Federal Information Processing Standards

(FIPS). See "Security Certifications Compliance" in the Cisco FXOS CLI Configuration Guide for the procedure

for enabling these modes using the CLI. See "Security Certifications Compliance" in the Cisco FXOS Firepower

Chassis Manager Configuration Guide for information for enabling these modes using the Firepower Chassis

Manager.

Note

The following figure shows a fully populated Firepower 9300.

Figure 1: Firepower 9300

See the Cisco Interactive Library for a video that displays the features and components of the Firepower 9300.

The following table lists the hardware features of the Firepower 9300.

Table 1: Firepower 9300 Features

DescriptionFeature

3 RUForm factor

Yes

Mount rails included (4-post EIA-310-D rack) with span between front and rear rails

of 24 to 36 in.

Rack mount

Front to rear

Cold aisle to hot aisle

Airflow

Cisco Firepower 9000 Supervisor with eight 10-Gigabit Ethernet ports and 2 network

module slots for I/O expansion

Supervisor

3Security module

slots

Located in the Supervisor

Network module

slots

Cisco Firepower 9300 Hardware Installation Guide

Overview

Features

DescriptionFeature

Cisco Firepower 9000 Security Module 24 with two SSDs in a RAID 1 configuration

Cisco Firepower 9000 Security Module 36 with two SSDs in a RAID 1 configuration

Cisco Firepower 9000 Security Module 44 with two SSDs in a RAID 1 configuration

Security modules

8-port 10-Gigabit Ethernet SFP+

4-port 40-Gigabit Ethernet QSFP+

2-port 100-Gigabit Ethernet QSFP28 (double-wide, occupies both network module

slots)

2-port 100-Gigabit Ethernet QSFP28

4-port 100-Gigabit Ethernet QSFP28

2-port 40-Gigabit Ethernet SFP+ fail-to-wire

6-port 10-Gigabit Ethernet SR/LR fiber fail-to-wire

You can deploy the Firepower 9300 as a dedicated threat sensor with

fail-to-wire network modules.

Note

Network modules

256-GB DDR4 DRAM per security moduleMemory

Up to twenty-four 10-Gigabit Ethernet (SFP+) interfaces; up to eight 40-Gigabit

Ethernet (QSFP+) interfaces with 2 network modules; up to four 100-Gigabit Ethernet

(SFP+) interfaces

Maximum number

of interfaces

One Gigabit Ethernet port on the Supervisor

Supports 1-G fiber or copper SFPs

Management port

One RJ-45 consoleSerial port

One USB 2.0 Type AUSB port

Yes

Displays serial number

Pullout asset card

Yes

On rear panel

Grounding lug

YesLocator beacon

Yes

On rear panel

The initial Firepower 9300 chassis does not have a power switch.

Note

Power switch

Two

On rear panel

Power supply slots

Cisco Firepower 9300 Hardware Installation Guide

Overview

Features

DescriptionFeature

AC, DC, and HVDC

Do not mix power supply types or wattage.

Note

Power supply types

Yes 1 + 1Redundant power

Four (hot-swappable)

On rear panel

Fan slots

Up to 2.4 TB per chassis (800 GB per security module in RAID 1 configuration)Storage

Chassis Components

The Firepower 9300 chassis contains the following components:

• Firepower 9300 Supervisor—Chassis supervisor module

• Management port

• RJ-45 console port

• USB Type A port

• Eight ports for 1- or 10-Gigabit Ethernet SFPs (fiber and copper)

• Firepower 9300 Security Module—Up to three security modules

• Firepower Network Module—Two single-wide network modules or one double-wide network module

• Two power supply modules (AC or DC)

• Four fan modules

Power Switch

The initial Firepower 9300 AC chassis has no external power switch. You reset the Firepower 9300 using

CLI commands. To physically power cycle the 9300, you must unplug the power cord and then plug the

power cord back in.

Note

After removing power from the chassis either by moving the power switch to OFF or unplugging the

power cord, wait at least 10 seconds before turning power back ON.

Note

The Firepower 9300 chassis has a standby power switch at the rear of the chassis. It controls both power

supply modules. You must shut down the software applications gracefully before turning the switch to

OFF.

Cisco Firepower 9300 Hardware Installation Guide

Overview

Chassis Components

Turning the switch to OFF turns off the main power to the Supervisor and the security modules regardless

of the software status, which can result in the loss of any data in transit and the corruption of data on the

SSDs. You must shut down the software applications gracefully before turning the switch to OFF.

Warning

Graceful Shutdown of the Chassis

You can gracefully shut down the chassis from either the CLI or Chassis Manager.

See the FXOS Configuration Guide for the procedure to shut down the chassis from the CLI. The graceful

shutdown usually takes as little as a few seconds to as long as three minutes. When the System Halted

message appears, you can move the power switch on the rear of the chassis to OFF.

See Powering Off the FXOS Chassis for the procedure to shut down the chassis from the Chassis Manager.

After the shutdown is completed, you can move the power switch on the rear of the chassis to OFF.

When you shut down the chassis, the security modules are automatically shut down.

Graceful Shutdown of the Security Modules

You can shut down the security modules individually from the CLI, the Chassis Manager, or you can

use the power switch on the front of each security module. Push the power button briefly on the front

panel of each security module. When the power button changes to amber, you can move the power switch

on the rear of the chassis to OFF.

Shut the security modules down individually when you are replacing a security module.

You must push the power button on every security module installed in the 9300 chassis. You can have

up to 3 security modules installed in the chassis.

Note

See the FXOS Configuration Guide for the procedure to shut down the security modules gracefully using

CLI commands from the Supervisor. When you see Oper Power: off for all slots, you can move the

power switch on the rear of the chassis to OFF.

See Powering On/Off a Security Module/Engine for the procedure to shut down the security module

from the Chassis Manager. After the shutdown is complete, you can move the power switch on the rear

of the chassis to OFF.

The shutdown commands are first available in Firepower FXOS version 2.0.1. See the FXOS Configuration

Guide for more information on using these commands.

Note

Deployment Options

Here are some examples of how you can deploy the Firepower 9300:

• At the core/aggregation layer of a three-tier data center in a high availability configuration.

• As a dedicated multifunction security service within converged infrastructure stacks (vBlock, FlexPod,

for example) at the access layer.

Cisco Firepower 9300 Hardware Installation Guide

Overview

Deployment Options

• As a high-performance data center security appliance between the WAN edge and data center core in an

high availability configuration.

• As a leaf that exclusively offers security functions in a spine/leaf data center design.

Package Contents

The following figure shows the package contents for the Firepower 9300. Note that the contents are subject

to change and your exact contents might contain additional or fewer items.

Figure 2: Firepower 9300 Package Contents

Blue console cable PC terminal adapter2Firepower 9300 chassis1

2 rack static rails

Adjusts to fit racks with a 24 in. to 36 in.

front-to-rear rail span

42 power cords (country specific)3

Four 10-32 retention nuts for

rack-mounting

6Four 10-32 x .5 in. screws used to attach

the rails to rack

10/100/1000BASE-T SFP transceiver8Four 10-32 x .75 in. Philips head screws

used to attach the chassis to the rack

Cisco Firepower 9300 Hardware Installation Guide

Overview

Package Contents

Otros manuales para Firepower 9300

Tabla de contenidos

Otros manuales de Cortafuegos de Cisco

Cisco

Cisco 5580-40 - ASA Firewall Edition Manual

Cisco

Cisco Small Business RV220W Manual de instrucciones

Cisco

Cisco Firepower 3500 Documento técnico

Cisco

Cisco Firepower 7010, Firepower 7020, Firepower 7030, Firepower 7050, Firepower 7110, Firepower 7120, Firepower 7115, Firepower... Manual de usuario

Cisco

Cisco Firepower 4110 Manual de usuario

Cisco

Cisco PIX 501 Manual de usuario

Cisco

Cisco ASA 5512-X Manual de usuario

Cisco

Cisco M195 Manual

Cisco

Cisco Small Business RV215W Manual de usuario

Cisco

Cisco M170 Manual de usuario

Cisco

Cisco Spam Manual de usuario

Cisco

Cisco S195 Manual

Cisco

Cisco Firepower 4100 Series Manual de usuario

Cisco

Cisco RV120W Manual de usuario

Cisco

Cisco Firepower 2120 Manual

Cisco

Cisco Firepower 1100 Series Manual

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario

Cisco

Cisco RV110W Manual de instrucciones

Cisco

Cisco PIX 501 Manual de usuario

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario

Cisco

Cisco ASA 5506-X Guía de inicio rápido

Cisco

Cisco Firepower 4100 Series Manual de instalación

Cisco

Cisco ASA 5506-X Instrucciones de instalación

Cisco

Cisco 3110 Manual

Manuales populares de Cortafuegos de otras marcas

Fortinet

Fortinet FortiGate Voice Series Manual de usuario

ADTRAN

ADTRAN NetVanta 2300 Manual de usuario

SecureLogix

SecureLogix ETM System Manual de usuario

NETGEAR

NETGEAR ProSafe FVX538 Manual de usuario

Lanner

Lanner FW-8877 Manual de usuario

Huawei

Huawei USG6000 Series Manual de instalación y operación

H3C

H3C SecPath F5000-AI-15 Manual de usuario

Nexcom

Nexcom DNA 1150 Manual de usuario

Fortinet

Fortinet FortiGate-60 series Manual de usuario

Draytek

Draytek Vigor2860 Series Manual de usuario

Lanner electronics

Lanner electronics FW-7650 Series Manual de usuario

Swisscom

Swisscom Internet Backup Manual de usuario

SonicWALL

SonicWALL NSa 5700 Manual de usuario

DPtech

DPtech FW1000 SERIES Manual de usuario

FEITIAN

FEITIAN MultiPass FIDO Manual de usuario

EBLOCKER

EBLOCKER PRO Manual de usuario

GTA

GTA GB-200 Manual de usuario

Trend Micro

Trend Micro Deep Edge Manual de usuario