Cisco CSS 11500 Manual de servicio
Corporate Headquarters:
Copyright © 2003. Cisco Systems, Inc. All rightsreserved.
Cisco Systems,Inc., 170 West Tasman Drive, San Jose, CA 95134-1706USA
Cisco 11500 Series Content Services Switch
Switch Control Module Reference
The CSS 11500 series Switch Control Module (SCM) provides master control and is responsible for the
following functions: system powerup and boot control, centralized routing table management,
system-wideconnection management,and interface toanexternal NetworkManagementStation.
Figure1shows an SCM (CSS5-SCM-2GE=).
Figure1SCMLEDs and Connectors
Only one SCM is required in a configuration, however you can install and configure a second SCM for
redundancy in a CSS 11506. A secondary SCM is passive, and does not load share processing functions
with the primary module. If the primary SCM fails, theCSS reboots and connections are terminated.
Thenthe secondary SCMbecomes primary automatically.
110-Mbps half-duplexEthernet
management connector 7Link and activity LEDfor the associated GBIC
connectorontheleft
2Bicolorstatus LED (green and red) 8RJ-45RS-232Console connector
3Amber status LED 9RJ-45 RS-232 Diag connector forfield service
diagnostic use only (A connectorcover is
provided. Removing the cover voidsthewarranty.)
4Link/Act LED
5Duplex LED 10 PCMCIA slotcover
6LC-type SFP GBICs (one of two) 11 PCMCIA slot 0 on the bottomcontaining a flash or
hard disk and slot 1 on top (shown empty)
59531
CSS5-SCM-2GE
SystemControl
DUPLEX
LINK/ACT
MANAGEMENT
10BASE-T
SLOT0
SLOT1
GE1 GE2 LINK
LINK
STATUS
PCMCIA
CONSOLE
2
19
8
3
4
5
6
7
10 11
2
Cisco11500 Series Content Services SwitchSwitch Control Module Reference78-13711-03
Note Beforeyou remove or install a module, make sure you properly ground yourself prior to handling the
module. For example,wearan antistaticwriststrap (included in the kit withthe module)and stick
the copper-tape end of the strap to an unpainted metal surface on the chassis. Make sure that the wrist
strap makes good contact with your skin.
Removing theSCM
Caution You must power down the CSS to removean SCM. If you remove a powered-on SCM from an
operational CSS, the CSS terminates all communications and reboots.
To remove anSCM:
1.Locatethe failed SCM (its Status LEDs willbe off). See Figure1.
2.If necessary, power down theCSS.
3.Remove all cablesfrom the module.
4.With a Phillips screwdriver, remove the PCMCIA cover and thenloosen the spring-loaded screws
on the frontof the modulefaceplate. See Figure2.
Figure2Removingthe PCMCIA Cover fromthe SCM
5.Extend both ejectors simultaneously to unseat themodule connector from the backplane and slide
the module out ofthe slot.
59602
CSS5-SCM-2GE
SystemControl
DUPLEX
LINK/ACT
MANAGEMENT
10BASE-T
SLOT0
SLOT1
GE1 GE2 LINK
LINK
STATUS
PCMCIA
CONSOLE
3
Cisco 11500 Series Content Services Switch Switch ControlModule Reference
78-13711-03
6.Remove the SFP GBICs from the SCM. Press the ejectors on the SFP GBICs. Slide them out of the
module and set them aside. See Figure3.
Figure3Ejecting theSFP GBIC from theSCM
7.Remove the flash or hard disks from the SCM. Press the ejectors to the rightof the disks. Slide them
out of the module and set them aside. See Figure4.
Figure4Ejecting theDiskfrom the SCM
Note Thereplacement SCM contains a 144 MB Small OutlineRamBus InlineMemory Module
(SO-RIMM). If your failed module has a288 MB SO-RIMM, you must remove its SO-RIMM, and
place it in the replacement SCM. See“Removing and Replacing the Memory Module” later in this
document.
Installingthe SCM
To install an SCM (refer to the previous illustrations):
1.Properly ground yourself prior to handlingthe module, as noted on the previous page.
2.If applicable, reinstallthe memory module, SFP GBICs, and flash or hard disks in the SCM.
3.Locate the slot in the chassis for the SCM. SCMs are restricted to slots 1 and 2.
1SFP GBIC ejector
123
CSS5-SCM-2GE
SystemControl
DUPLEX
LINK/ACT
MANAGEMENT
10BASE-T
SLOT0
SLOT1
GE1GE2 LINK
LINK
STATUS
PCMCIA
CONSOLE
67902
GE2
1
1Disk ejector
123
CSS5-SCM-2GE
SystemContl
DUPLEX
LINK/ACT
MANAGEMENT
10BASE-T
SLOT0
SLOT1
GE1GE2 LINK
LINK
STATUS
PCMCIA
CONSOLE
59532
1
4
Cisco11500 Series Content Services SwitchSwitch Control Module Reference78-13711-03
4.Insertthe moduleinto the board guides atthe left and right sides of the slot, and then slidethe
module into the chassis bypressing firmly at the leftand right of the faceplate.
5.Close both ejectors simultaneously to seatthe moduleconnector into the backplane.
6.Using aPhillips screwdriver,tighten the spring-loaded screws on the front ofthe module faceplate.
7.With a Phillips screwdriver, replace the PCMCIA cover (see Figure2) and then tighten the
spring-loadedscrews on the front of the modulefaceplate.
8.Replace the cables. Note that the SFP GBICs haveLC-type connectors and require LC-type fiber
cables.
9.Reboot the CSS.
10.If you installed a secondary SCM, use the passive sync command to copy the boot config from the
primary SCM to the secondary SCM.
If you installed a replacement for a primary SCM,the replacementhas defaultsettings for the
administrative username and password, IP address, subnet mask, and primary boot record. To
reconfigure these parameters, access the Offline Diagnostic Monitor menu at the boot prompt. For
information on using the Offline Diagnostic Monitor menu, refer to the Content Services Switch
Administration Guide.
Table 1 describes the SCM LEDs and their indications.
Related CLI Commands
To view the current state of the SCM and verify it is powered on as indicated by the primary or secondary
state,use the show chassis command.
Table1SwitchControl Module LED Descriptions
LED Name Color State Indicates
Status (left) Green Solid The moduleis ready.
Variable blink Disk activity isoccurring.
Slow blink Another CSS module has failed.
Red Solid The module failed the power-up self test during the boot
process.
Slowblink The modulefailed.
No colorOffThe modulefailedand has no power.
Status (right) Amber Slow blink The moduleis offline and active.
Solid The moduleis onlineand not active(secondary).
Link/Act
for the Ethernet
Management Port
Green OffThere is no link.
On The link is established butthere is no activity.
Blinking The link is established with transmit or receive activity.
Link
for each Gigabit
Ethernet Port
Green OffThere is no link.
On The link exists and synchronization isachieved.
Blinking The link is established with transmit and receive activity.
5
Cisco 11500 Series Content Services Switch Switch ControlModule Reference
78-13711-03
Removing and Replacingthe Memory Module
To remove and replace amemorymodule:
1.Place the modulefaceup on a flat antistatic surface.
2.Locate the SO-RIMM connector on the rear of the module. See Figure 5.
Figure5MemoryModule Location
3.Slightly extend the locking tabs on both sides of the memory module to release it. Gently pull the
module out of the connector. See Figure 6.
Figure6MemoryReplacement
4.Align the replacement memory module so that the rowof gold contacts on thememory module are
facingtherow ofgoldpins insidetheconnector.
5.Insertthe memory module into the connector at approximately a 30 degree angle (see Figure 6) and,
with gentle pressure, push the module into the connector until the module fits snugly against the
back of theconnector. At this point, themodule is still at an angle above the locking tabs.
6.Gently push straight down on the edges of the module until the tabs lock itinto place.
1Memory module
SystemControl
1
59620
1SO-RIMM connector tab
59547
1
6
Cisco11500 Series Content Services SwitchSwitch Control Module Reference78-13711-03
Otros manuales de Unidad de control de Cisco
Cisco
Cisco MGX RPM-XF Manual de usuario
Cisco
Cisco C3850-NM-4-1G Manual de instrucciones
Cisco
Cisco 3110 Manual de usuario
Cisco
Cisco SM-X-1T3/E3 Manual de usuario
Cisco
Cisco Firepower 4110 Manual de usuario
Cisco
Cisco Catalyst 5000 Series Manual de usuario
Cisco
Cisco TelePresence MCU 4500 Series Manual de usuario
Cisco
Cisco ATUC-4DMT-ISDN Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco NM-1CT1 Guía de inicio rápido
Cisco
Cisco Catalyst 9400 Series Manual de instalación y operación
Cisco
Cisco CGM-WPAN-OFDM-FCC Manual de usuario
Cisco
Cisco ONS 15540 ESPx Manual de instrucciones
Cisco
Cisco TelePresence MCU 4200 Series Manual de usuario
Cisco
Cisco GS7000 Instrucciones de funcionamiento
Cisco
Cisco LightStream 1010 Guía de inicio rápido
Cisco
Cisco GS7000 Manual del operador
Cisco
Cisco 6015 Manual de uso y cuidado
Cisco
Cisco ONS 15200 Manual de usuario
Cisco
Cisco WS-G5484 Manual de usuario
Cisco
Cisco FlexWAN Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
