Cisco Firepower 4110 Manual de usuario
Installation, Maintenance, and Upgrade
•Install, Remove, and Replace the Network Module, on page 1
•Remove and Replace the Fan Module, on page 4
•Remove and Replace the SSD, on page 6
•Remove and Replace the Power Supply Module, on page 9
•Connect the DC Power Supply Module, on page 13
•Secure the Power Cord on the AC Power Supply Module, on page 19
•Install the FIPS Opacity Shield, on page 22
Install, Remove, and Replace the Network Module
Hot Swapping
Starting with FXOS 2.3.1, the Firepower 10-Gb and 40-Gb network modules (without hardware bypass
support) support hot swapping, but you must hot swap with an identical network module, that is, a network
module with the same PID. See Product ID Numbers for the network module PIDs. You must bring the
network module offline using the appropriate CLI commands before removing the network module from
the chassis so that all network module configuration is saved. See the “Taking a Network Module Offline
or Online” topic in the Security Module/Engine Management chapter in the Cisco FXOS Firepower
Chassis Manager Configuration Guide.
We do not recommend that you remove the network module without bringing it properly offline using
the appropriate CLI commands.
Caution
You must have ROMMON 1.0.10 or later on the Supervisor to support hot swapping. For the ROMMON
upgrade procedure, see the "Firmware Upgrade" topic in the Image Management chapter in the Cisco
FXOS Firepower Chassis Manager Configuration Guide for your software version.
Note
To remove and replace the network modules that do not currently support hot swapping, power off the
chassis, replace the network module, and then power the chassis back on.
Acknowledgment is necessary if you decommission and physically remove a network module and do
not replace it, or if you replace it with another PID. See the "Acknowledging a Security Module/Engine”
Installation, Maintenance, and Upgrade
1
topic in the Security Module/Engine Management chapter in the Cisco FXOS Firepower Chassis Manager
Configuration Guide.
Safety Warnings
Take note of the following component replacement safety warnings:
Statement 1028—More Than One Power Supply
This unit might have more than one power supply connection. To reduce risk of electric shock, remove
all connections to de-energize the unit.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1089—Instructed and Skilled Person Definitions
An instructed person is someone who has been instructed and trained by a skilled person and takes the
necessary precautions when working with equipment.
A skilled person or qualified personnel is someone who has training or experience in the equipment
technology and understands potential hazards when working with equipment.
Warning
Statement 1090—Installation by Skilled Person
Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089
for the definition of a skilled person.
Warning
Statement 1091—Installation by an Instructed Person
Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.
See statement 1089 for the definition of an instructed or skilled person.
Warning
Installation, Maintenance, and Upgrade
2
Installation, Maintenance, and Upgrade
Install, Remove, and Replace the Network Module
This procedure describes how to install a network module into an empty slot that has never contained a network
module, and how to remove an installed network module and replace it with another network module.
Step 1 To install a new network module for the first time into an empty slot, do the following:
a) Power down the chassis by moving the power switch to the OFF position.
See Rear Panel for more information about the power switch.
b) Follow Steps 4 through 7 to install the new network module.
c) Power on the chassis by moving the power switch to the ON position.
The state for the new network module is OIR Failed.
d) To change the status of the network module to Online, reboot the chassis. See the "Rebooting the Firepower 4100/9300
Chassis" topic in the System Administration chapter in the FXOS Configuration Guide for your software version.
Step 2 To remove and replace an existing network module, do one of the following:
a) Save your configuration.
b) Power down the chassis by moving the power switch to the OFF position (if removing a network module that does
not support hot swapping).
See Rear Panel for more information about the power switch.
c) Bring the network module offline using the appropriate CLI command (if removing a network module that supports
hot swapping). All network module configuration is saved. See the “Taking a Network Module Offline or Online”
topic in the Security Module/Engine Management chapter in the FXOS Configuration Guide for your software version.
d) Continue with Step 3.
Step 3 To remove a network module from the chassis, loosen the captive screw on the lower left side of the network module
and pull out the handle that is connected to the screw. This mechanically ejects the network module from the slot.
Figure 1: Remove the Network Module
Installation, Maintenance, and Upgrade
3
Installation, Maintenance, and Upgrade
Install, Remove, and Replace the Network Module
If the slot is to remain empty, install a blank faceplate to ensure proper airflow and to keep dust out of the chassis;
otherwise, install another network module.
Step 4 To replace a network module, hold the network module in front of the network module slot on the right of the chassis
and pull the network module handle out.
Step 5 Slide the network module into the slot and push it firmly into place until the handle is flush with the front of the network
module.
Step 6 Tighten the captive screw on the lower left side of the network module.
Step 7 Do one of the following:
a) Power up the chassis so that the new network module is recognized (if the new network module does not support hot
swapping).
b) Bring the new network module online using the appropriate CLI command (if the new network module supports hot
swapping). The saved network module configuration is automatically reapplied when the network module is back
online.
If you install a network module that is a different PID than the original network module, the saved
configuration is deleted and the default configuration is applied. You must enter the acknowledge command
to confirm the network module PID change:
Note
What to do next
Follow the procedures in the FXOS Configuration Guide to connect to the network module and make sure
that it has been discovered correctly by the Firepower 4100.
Remove and Replace the Fan Module
You can remove and replace fan modules while the system is running. The air flow moves from front to back.
If you remove a fan or a fan fails, the other fans operate at full speed, which can be noisy.
The system supports operation with a single fan failure (N+1 fan redundancy), but do not run the system for
an extended amount of time without all fan modules installed. Keep removal and replacement time at three
minutes. Remove and replace one fan module at a time.
Note
Safety Warnings
Take note of the following component replacement safety warnings:
Installation, Maintenance, and Upgrade
4
Installation, Maintenance, and Upgrade
Remove and Replace the Fan Module
Statement 1028—More Than One Power Supply
This unit might have more than one power supply connection. To reduce risk of electric shock, remove
all connections to de-energize the unit.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1089—Instructed and Skilled Person Definitions
An instructed person is someone who has been instructed and trained by a skilled person and takes the
necessary precautions when working with equipment.
A skilled person or qualified personnel is someone who has training or experience in the equipment
technology and understands potential hazards when working with equipment.
Warning
Statement 1090—Installation by Skilled Person
Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089
for the definition of a skilled person.
Warning
Statement 1091—Installation by an Instructed Person
Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.
See statement 1089 for the definition of an instructed or skilled person.
Warning
Step 1 To remove a fan module, face the rear of the chassis, and grasp the handle of the fan module.
Step 2 Squeeze the handle to disengage the latches on the left and right of the fan module.
Step 3 Pull the fan module out of the chassis.
Installation, Maintenance, and Upgrade
5
Installation, Maintenance, and Upgrade
Remove and Replace the Fan Module
Figure 2: Remove the Fan Module
Step 4 To replace a fan module, hold the fan module in front of the fan slot.
Step 5 Push the fan module into the chassis until it is properly seated and the latches snap into place.
If the system is powered on, listen for the fans. You should immediately hear the fans operating. If you do not hear the
fans, make sure the fan module is inserted completely into the chassis and the faceplate is flush with the outside surface
of the chassis.
Step 6 Verify that the fan is operational by checking the fan module LED. See Front Panel LEDs for a description of the fan
LEDs.
Remove and Replace the SSD
Although the hardware supports removing and replacing SSDs while the system is running, the software does
not currently support hot swapping. You must power down the chassis to remove and replace SSDs.
If your Firepower 4100 is running Firepower Threat Defense software, we recommend that you upgrade to
the latest version to take advantage of software updates that enhance SSD management performance and
longevity.
Note
You storage SSD must be installed in slot 1 and must be present. Only an optional MSP can be installed in
the second SSD slot (SSD slot 2). The MSP stores threat detection results for use in future analysis. It supports
Installation, Maintenance, and Upgrade
6
Installation, Maintenance, and Upgrade
Remove and Replace the SSD
the Advanced Malware Protection software feature. The MSP is supported beginning in FXOS 2.0.1. It is
used as both storage and as the Malware application repository. RAID is not supported.
Do not switch the two SSDs. The storage SSD must be installed in slot 1. The optional MSP SSD must be
installed in slot 2. If you remove it and install it in slot 1, all stored file capture data is lost.
Caution
Safety Warnings
Take note of the following component replacement safety warnings:
Statement 1028—More Than One Power Supply
This unit might have more than one power supply connection. To reduce risk of electric shock, remove
all connections to de-energize the unit.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1089—Instructed and Skilled Person Definitions
An instructed person is someone who has been instructed and trained by a skilled person and takes the
necessary precautions when working with equipment.
A skilled person or qualified personnel is someone who has training or experience in the equipment
technology and understands potential hazards when working with equipment.
Warning
Statement 1090—Installation by Skilled Person
Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089
for the definition of a skilled person.
Warning
Installation, Maintenance, and Upgrade
7
Installation, Maintenance, and Upgrade
Remove and Replace the SSD
Statement 1091—Installation by an Instructed Person
Only an instructed person or skilled person should be allowed to install, replace, or service this equipment.
See statement 1089 for the definition of an instructed or skilled person.
Warning
Step 1 Save your configuration.
Step 2 Power down the chassis by moving the power switch to the OFF position. See Features for more information about the
power switch.
Step 3 To remove an SSD, face the front of the chassis, loosen the two captive screws on the SSD, and gently pull it out of slot
1 of the chassis.
Figure 3: Remove the SSD
Step 4 To replace the SSD, make sure the power switch is still in the OFF position, and then hold the SSD in front of slot 1 and
push it in gently until it is seated.
Step 5 To install the MSP SSD, make sure the power switch is still in the OFF position and then remove the blank faceplate in
slot 2 by loosening the captive screws on either side of the faceplate.
Step 6 Hold the MSP SSD in front of slot 2 and push it in gently until it is seated.
Do not switch the two SSDs. Only the optional MSP SSD can be installed in slot 2. If you remove it and install
it in slot 1, all stored file capture data is lost.
Caution
Step 7 Tighten the captive screws on either side of the SSD.
Step 8 Verify that the SSD is operational by checking the SSD LED. See Front Panel LEDs for a description of the fan LEDs.
Installation, Maintenance, and Upgrade
8
Installation, Maintenance, and Upgrade
Remove and Replace the SSD
Remove and Replace the Power Supply Module
You can remove and replace power supply modules while the system is running.
Safety Warnings
Take note of the following power and component removal safety warnings:
Statement 347—Failure to Secure the Expansion Module
To reduce the risk of electric shock, secure the modules with the provided screws.
Warning
Statement 1003—DC Power Disconnection
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Warning
Statement 1005—Circuit Breaker
This product relies on the building’s installation for short-circuit (overcurrent) protection. To reduce risk
of electric shock or fire, ensure that the protective device is rated not greater than:
AC: 20A
DC: 40A
Warning
Statement 1017—Restricted Area
This unit is intended for installation in restricted access areas. Only skilled, instructed, or qualified
personnel can access a restricted access area.
Warning
Statement 1018—Supply Circuit
To reduce risk of electric shock and fire, take care when connecting units to the supply circuit so that
wiring is not overloaded.
Warning
Statement 1022—Disconnect Device
To reduce risk of electric shock and fire, you must incorporate a readily accessible two-poled disconnect
device in the fixed wiring.
Warning
Installation, Maintenance, and Upgrade
9
Installation, Maintenance, and Upgrade
Remove and Replace the Power Supply Module
Statement 1025—Use Copper Conductors Only
To reduce risk of fire, use copper conductors only.
Warning
Statement 1028—More Than One Power Supply
This unit might have more than one power supply connection. To reduce risk of electric shock, remove
all connections to de-energize the unit.
Warning
Statement 1029—Blank Faceplates and Cover Panels
Blank faceplates and cover panels serve three important functions: they reduce the risk of electric shock
and fire, they contain electromagnetic interference (EMI) that might disrupt other equipment, and they
direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates,
front covers, and rear covers are in place.
Warning
Statement 1030—Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1073—No User-Serviceable Parts
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1046—Installing or Replacing the Unit
To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always
be made first and disconnected last.
Warning
Installation, Maintenance, and Upgrade
10
Installation, Maintenance, and Upgrade
Remove and Replace the Power Supply Module
Otros manuales para Firepower 4110
2
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Unidad de control de Cisco
Cisco
Cisco Firepower 4112 Manual
Cisco
Cisco HPNA Manual de usuario
Cisco
Cisco MEM-NP8F Series Guía de inicio rápido
Cisco
Cisco T3 Guía de inicio rápido
Cisco
Cisco Catalyst 9400 Series Manual de instalación y operación
Cisco
Cisco EHWIC-3G-EVDO Manual de usuario
Cisco
Cisco WS-G5484 Manual de usuario
Cisco
Cisco ATUC-4DMT-ISDN Instrucciones de funcionamiento y mantenimiento
Cisco
Cisco NM-1E2W Guía de inicio rápido
Cisco
Cisco CGM-WPAN-OFDM-FCC Manual de usuario
Cisco
Cisco NM-1CT1 Guía de inicio rápido
Cisco
Cisco FlexWAN Manual de usuario
Cisco
Cisco TelePresence MCU 4200 Series Manual de usuario
Cisco
Cisco TelePresence Touch10 Manual de usuario
Cisco
Cisco Catalyst 3110G Manual
Cisco
Cisco GS7000 Instrucciones de funcionamiento
Cisco
Cisco 6015 Manual de uso y cuidado
Cisco
Cisco T1 Manual de usuario
Cisco
Cisco ONS 15200 Manual de usuario
Cisco
Cisco NCS 1010 Hoja de instrucciones
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
