Charder MS2500 Manual de uso y cuidado

- 1 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

MS-2500/MS-3800/MS-3900/MS-4600/MS-5400

Calibration Manual

Software ver. UP1911 1.12

- 2 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

CONTENTS

PRECAUTIONS....................................................................................................... - 3 -

GENERAL INFORMATION ..................................................................................... - 3 -

KEY AND FUNCTIONS ........................................................................................... - 4 -

KEY FUNCTIONS............................................................................................. - 4 -

FUNCTION SETTING DESCRIPTION.............................................................. - 4 -

FUNCTION FLOWS ................................................................................................ - 5 -

FULL FUNCTION FLO .................................................................................. - 6 -

MULTI DI ISION SETTING ..................................................................................... - 7 -

CALIBRATION ........................................................................................................ - 8 -

GRADUATION SETTING(OIML CLASS III) ............................................................ - 9 -

- 3 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

PRECAUTIONS

READ this manual BEFORE operation or servicing this equipment.

FOLLOW these instructions carefully.

SA E this manual for future reference.

DO NOT allow untrained personnel to operate, clean, inspect, maintain, service or

tamper with this equipment.

ALWAYS DISCONNECT this equipment from the power source before cleaning or

performing maintenance.

Note: If the unit has been stored or transported in below freezing temperatures, allow

the unit to warm up to room temperature before turning on power.

PAY SPECIAL ATTEHNTION TO ALL “WARNING” SYMBOLS

GENERAL INFORMATION

Before connecting or disconnecting any internal electronic components or

interconnecting wiring between electronic equipment, always remove power and wait at

least 30 seconds. Failure to observe these precautions could damage or destruction of

the equipment.

IMPORTANT ELECTRICAL ARNING

FCC COMPLIANCE STATEMENT

ARNING! This equipment generates, uses and can radiate radio frequency

and if not installed and used in accordance with the instruction manual, may cause

interference to radio communications. It has been tested and found to comply

with the limits for a Class A computing device pursuant to Subpart J of Part 15 of

FCC rules, which are designed to provide reasonable protection against such

interference when operated in a commercial environment. Operation of this

equipment in a residential area may cause interference in which case the user will

be responsible to take whatever measures necessary to correct the interference.

- 4 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

KEY AND FUNCTIONS

KEY FUNCTIONS

ON/OFF Press to switch scale on and off.

ZERO KEY Press to zero the scale.

BMI Press to enable BMI function.

HOLD Press to lock weighing result.

UNITS Press to select weighing units between kg,lb,st

ENTER Press to confirm the function or numeral key.

CLEAN Cleaning error input of numeral key.

Key Pad 0~9 Entering numeral 0~9

PRE-SET TARE Press to set pre-tare weight.

SEMI AUTO TARE Press to tare the weight of current loading object.

PRINT Press to print result.

4key type indicator

FUNCTION SETTING DESCRIPTION

(Units) : ( Kg / Lb / St ) set up weighing unit on and off.

(Graduations ) : graduations、max capacity、division , refer to figure (1)

( eight Section Division) : multi division set up

(Auto-Zero-Tracking-Range)：zero tracking range set up ( 0.25d/0.5d/1d/3d/OFF )

(Stable-Range)：stable range set up ( 0.25d/0.5d/1d/3d/OFF )

(Zero Range)：zero range set up ( 2% / 100% )

(Over Load Range)：overload set up ( 9d / 2% )

(Calibration Set)：calibration function set up

(Auto-Off Time)：auto off set up (120 SEC. / 180 SEC. / 240 SEC. / 300 SEC. / OFF)

(Buzzer)：beeper (ON / OFF)

(Defult Setup)：restore default setting

- 5 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

FUNCTION FLO S

Press ZERO (4 key indicator: UNIT) for three seconds when LCD show then,

release the button. LCD now is showing (unit) first function in function setting

mode. Following are mainstream of function flow.

Press SEMI AUTO TARE to select function.

Press HOLD to confirm selection.

- 6 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

FULL FUNCTION FLO

- 7 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

MULTI DIVISION SETTING

***NOTE***

-Only two divisions are accepted. For example: Max capacity 300kg, multi capacity

can be 0~200kgx100g and 201~300kgx200kg. It depends on loadcell capability and

standard restriction.

-Multi division setting can’t be lower than 0kg. hen it is at 0kg means it is full

capacity now.

Press ENTER to

confirm setting.

For 20key indicator:

input target division in kg.

For 4key indicator:

TARE to reduce numeral

UNIT to clear input

HOLD to move to next

digit.

***To confirm

setting by

moving to “ t-d”.

Full capacity multi capacity

& division

- 8 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

CALIBRATION

：Press HOLD key

：Press SEMI AUTO TARE to select.

Select between kg and lb for calibration

hen LCD shows span count press ENTER (4Key indicator: UNIT )

to store span count.

First, set up calibrating point( how many kg(lb). Then press ENTER

to zero span count. Loading dead weight up to calibrating point. Press ENTER to

calibrate and store the result. You will back to normal mode.

For 4key indicator,

HOLD means to move to next digit and final confirm the result.

UNIT means to zero span count.

calibrating

unit kg

calibrating

unit lb

LCD shows span count

Entering calibrating point

and store span count

Zero the

span count

Loading dead

weight to

calibrate scale.

- 9 -

CHARDER ELECTRONIC CO., LTD CALIBRATION MANUAL COPY RIGHT RESERVED 200906 V1

GRADUATION SETTING(OIML CLASS III)

NO.

500d 1000d 1500d 2000d 2500d 3000d 6000d 10000d

1.002 kg

1.001 kg

1.501 kg 1.0005 kg

1.2505 kg 1.5005 kg 1.2002 kg 1.0001 kg

2.505 kg

2.002 kg

3.002 kg 2.001 kg

2.501 kg 3.001 kg 3.0005 kg

2.0002 kg

5.01 kg 5.005 kg

7.505 kg 4.002 kg

5.002 kg 6.002 kg 6.001 kg 5.0005 kg

10.02 kg

10.01 kg

15.01 kg 10.005 kg

12.505 kg 15.005 kg 12.002 kg 10.001 kg

25.05 kg

20.02 kg

30.02 kg 20.01 kg

25.01 kg 30.01 kg 30.005 kg

20.002 kg

50.1 kg

50.05 kg

75.05 kg 40.02 kg

50.02 kg 60.02 kg 60.01 kg 50.005 kg

100.2 kg

100.1 kg

150.1 kg 100.05 kg

125.05 kg 150.05 kg 120.02 kg 100.01 kg

250.5 kg

200.2 kg

300.2 kg 200.1 kg

250.1 kg 300.1 kg 300.05 kg

200.02 kg

501 kg 500.5 kg

750.5 kg 400.2 kg

500.2 kg 600.2 kg 600.1 kg 500.05 kg

1002 kg 1001 kg

1501 kg 1000.5 kg

1250.5 kg 1500.5 kg 1200.2 kg 1000.1 kg

2505 kg 2002 kg

3002 kg 2001 kg 2501 kg 3001 kg 3000.5 kg

2000.2 kg

5010 kg 5005 kg

7505 kg 4002 kg 5002 kg 6002 kg 6001 kg 5000.5 kg

10020 kg 10010 kg

15010 kg 10005 kg

12505 kg 15005 kg 12002 kg 10001 kg

press HOLD to select

please refer to table below.

Otros manuales para MS2500

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Charder

Charder

Charder MS4400I Manual de usuario

Charder

Charder MS3400-1 Manual de usuario

Charder

Charder DP3700 Manual de usuario

Charder

Charder MS5461 Manual de usuario

Charder

Charder R260 Manual de usuario

Charder

Charder MS 5900 Manual de usuario

Charder

Charder MS2510 Manual

Charder

Charder MS3400 Manual de usuario

Charder

Charder MS 6000 Manual de usuario

Charder

Charder W320 Manual de usuario

Charder

Charder MHS2710 Manual de usuario

Charder

Charder MS 3850 Manual de usuario

Charder

Charder MS 2400 Manual de usuario

Charder

Charder MS 4211 Manual de usuario

Charder

Charder MS2504 Manual de usuario

Charder

Charder MS 5460 Manual de usuario

Charder

Charder MS3830 Manual de usuario

Charder

Charder MS4400 Manual de usuario

Charder

Charder MS 2400 Manual de usuario

Charder

Charder W310 Manual de usuario

Charder

Charder Z410 Manual de usuario

Charder

Charder MHS2510/2610 Manual de usuario

Charder

Charder MS 2100 Manual de usuario

Charder

Charder MHS2510I Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario