Chamberlain RED/GREEN LIGHT CONTROL KIT Manual de usuario

RED/GREEN LIGHT

CONTROL KIT

FOR USE WITH LOGIC 2 OR 3 MODEL APT, T, AND GT OPERATORS

ACCESSORY P/N: RDGRNCARD

To prevent possible SERIOUS INJURY or DEATH from

electrocution, disconnect electric power to operator BEFORE

installing.

ALL electrical connections MUST be made by a qualified

individual.

Step 1

Step 4

Side View

Red/Green

Light Control

Module

Logic Board

Electrical Box

Step 3

Step 2

INSTALLATION

MOUNT THE LIGHT BOX

STEP 1:

Attach mounting bracket to the electrical box with the

self-threading screws (2) provided.

STEP 2:

Remove light box cover. Fasten light box to mounting bracket

with self-threading screws (2) provided.

STEP 3:

Attach flex conduit to electrical box.

STEP 4:

Insert Red/Green Light Control Module into either of the two

slots located on the logic board (see step 4 illustration).

NOTE: To avoid damage to relays, do not exceed the following:

• Red light output - 75W, 120V incandescent bulb or 3A,

250VAC (Resistive load).

• Green light output - 75W, 120V incandescent bulb or 3A,

250VAC (Resistive load).

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause

cancer or birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov

LOGIC 2

To Program open Mid-Stop:

1. Close the door.

2. Set dip switches to "Set Mid-Stop".

3. Press open (the door will begin moving).

4. Press stop when the desired Mid-Stop height is reached.

5. Return the dip switches to the desired wiring type (C2, B2,

etc.). The door will now stop at this height every time the door

is opened.

WARNING DEVICES MODULE

LOAD

+5V +24V

OUT

+24VDC

10 84

TB1

13 +

TB2

RED

LT.

GREEN

LT.

120V IN

L1 L2

Figure 1

Light

Light box conduit w/wires Power LEDs 24 Vdc for Horn/Strobe

115 Vac power only

SET

MID-STOP

OFF

STEP 5: (FIGURE1)

Complete wiring connections as follows:

• Connect red wire to red light terminal on the Red/Green Light

Control Module connector.

• Connect black wire to green light terminal on the Red/Green

Light Control Module connector.

• Connect white wire to L1 (NEUTRAL) on the power terminal

strip.

• Connect black jumper from L2 (HOT) on the power terminal

strip to (120V IN) terminal on the Red/Green Light Control

Module connector.

STEP 6:

Install red and green light bulbs (not provided). Maximum

wattage should not exceed 75 watts.

OPTIONAL MID-STOP PROGRAMMING:

LOGIC 3

To Program open or down (close) Mid-Stop:

1. Open the door to set close Mid-Stop or close door to set open

Mid-Stop.

2. Turn selector dial to “PROGRAM.”

3. Press the “MID SET” button on logic board.

4. Press the OPEN button for open Mid-Stop, wait until the door

reaches the desired Mid-Stop height, then press the STOP

button.

Press the CLOSE button for down Mid-Stop, wait until the

door reaches the desired Mid-Stop height, then press the

STOP button.

5. Press the MID SET button to complete programming.

6. Turn selector dial back to desired wiring type.

1 2 3 4

Green

Light

Red

Light

Red

WhiteWhite

Black

LIGHT CONTROL MODULE OPERATION

The green lights on the option board will turn on if the board is

seated properly and the power is on. When the door reaches the

full open position or programmed mid-stop, the timer circuit will

be activated. The green lamp holder will receive power. If the

timer has not been set, the red lamp holder will receive power

when the door starts to close and until close limit is activated. If

the timer has been set, the red lamp holder will receive power as

indicated by the chart below.

NOTE:

A) The green lamp holder will never receive power if the timer is

set to ten seconds or less. The red lamp holder will blink for one

second on and one second off whenever the door is moving,

even if the timer to close has not been programmed.

B) The 24 Vdc output is for the addition of an optional Horn/

Strobe. When the operator is running OPEN or CLOSE and the

RED warning light is flashing, the output will activate the Horn/

Strobe.

TIMER SETTING RED LAMP HOLDER

RECEIVES POWER

Greater than or equal to

10 seconds

10 seconds before door starts to

close and until close limit is

activated

Less than 10 seconds Immediately after reaching open

limit or mid-stop

Wiring Mode Up Mid-Stop Down Mid-Stop

B2, C2, E2 Stop movement, wait for user input:

3-Button Control Station will OPEN or

CLOSE on command Single Button

Control/Radio will OPEN on command.

Down Mid-Stop disabled

D1 Up Mid-Stop disabled Down Mid-Stop disabled

T, TS, FSTS Stop movement, wait for user input:

3-Button Control Station will OPEN or

CLOSE on command Single Button

Control/Radio will OPEN on command. If

timer to close set is set for up Mid-Stop,

timer to close will close the door

Stop movement, then count down timer to close timer & auto

User input during timer to close countdown:

3-Button Control Station will OPEN the door, CLOSE the door, or

STOP the countdown

Single Button Control will CLOSE on command

Radio will OPEN on command

Red/Green enabled at Mid-Stop

Failsafe B2, Failsafe C2 Stop movement, wait for user input:

3-Button Control Station will OPEN or

CLOSE on command

Single Button Control/Radio will OPEN

open command

Down Mid-Stop disabled

Failsafe D1 Up Mid-Stop disabled Down Mid-Stop disabled

Failsafe E2 Stop movement, wait for user input:

3-Button Control Station will OPEN or

CLOSE on command

Down Mid-Stop disabled

01-31098E

Otros manuales de Controladores de Chamberlain

Chamberlain

Chamberlain CAP2D Manual de usuario

Chamberlain

Chamberlain 320LM Manual de usuario

Chamberlain

Chamberlain Security+ 974-315CB Manual de usuario

Chamberlain

Chamberlain CB124EV Manual de usuario

Chamberlain

Chamberlain 872 Series Manual de usuario

Chamberlain

Chamberlain CAP2D Manual de usuario

Chamberlain

Chamberlain myQ 821LM Manual de usuario

Chamberlain

Chamberlain MyQ Manual de usuario

Chamberlain

Chamberlain T Manual de usuario

Chamberlain

Chamberlain LA400UL Guía de inicio rápido

Chamberlain

Chamberlain CAP2D Manual de usuario

Chamberlain

Chamberlain CLLACD Manual de usuario

Chamberlain

Chamberlain Liftmaster PROFESSIONAL 412-315HM Manual de usuario

Chamberlain

Chamberlain AGO250L Manual de usuario

Chamberlain

Chamberlain CLDM1ANZ Manual de usuario

Chamberlain

Chamberlain LiftMaster Professional CB224 Manual de usuario

Chamberlain

Chamberlain LiftMaster K001A6039 Manual de usuario

Chamberlain

Chamberlain 874 Series Manual de usuario

Chamberlain

Chamberlain Security+ CLLA1 Manual de usuario

Chamberlain

Chamberlain 855CB Manual de usuario

Chamberlain

Chamberlain 772CB Manual de usuario

Chamberlain

Chamberlain Security+ 974CB Manual de usuario

Chamberlain

Chamberlain SECURITY+ WPB3LM3 Manual de usuario

Chamberlain

Chamberlain LA412UL Guía de inicio rápido

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario