CDA EVS90BL Guía de inicio rápido

www.cda.eu

EVS90BL

Ceiling extractor

Installation, use and maintenance

Contents:

3 Important

5 Important information

6 Using your extractor

8 Care and maintenance

9 Removing the grease ﬁlters

10 - 14 Installation

10 Installation preparation - height

11 Cut-out information

12 Fitting the extractor

13 Fitting the motor group

14 Ducting

15 Mains electricity connection

16 Electrical information

16 Troubleshooting

19 Energy Eciency Information

Important

The CDA Group Ltd cannot be held responsible for injuries or losses

caused by incorrect use or installation of this product. Please note that

CDA reserve the right to invalidate the guarantee supplied with this

product following incorrect installation or misuse of the appliance or

use in a commercial environment.

This appliance is not designed to be used by people (including

children) with reduced physical, sensorial or mental capacity, or

who lack experience or knowledge about it, unless they have had

supervision or instructions on how to use the appliance by someone

who is responsible for their safety.

Under no circumstances, except for instructions laid out in this manual,

should any external covers be removed for servicing or maintenance

except by suitably qualiﬁed personnel.

Appliance information:

Please enter the details on the appliance rating plate below for

reference, to assist CDA Customer Care in the event of a fault with

your appliance and to register your appliance for guarantee purposes.

Appliance Model

Serial Number

EU Declarations of Conformity:

This appliance has been manufactured to the strictest standards and

complies with all applicable legislation, including Gas safety, Electrical

safety (LVD) and Electromagnetic interference compatibility (EMC).

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE

PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2012/19/EU.

At the end of its working life, the product must be taken to a special

local authority waste collection centre or to a dealer providing

appliance recycling services.

Disposing of a household appliance separately avoids possible

negative consequences for the environment and health. It also

enables the constituent materials to be recovered, saving both energy

and resources. As a reminder of the need to dispose of household

appliances separately, the product is marked with a crossed-out

wheeled dustbin.

IMPORTANT:

• Under no circumstances should the extractor be

connected to any gas ventilation system, ﬂue system or

hot air ducting system.

• Do not vent the extractor into an attic or loft space.

• Only house the extractor in rooms with adequate

ventilation. Remember that the extractor is powerful and

whatever air is extracted needs to be replaced.

• Do not tile the extractor in. It should be removable for

service or maintenance.

• Do not use silicone sealant to secure the hood to the wall.

• You must be able to isolate the extractor from the mains

electrical supply after installation.

• This extractor has been designed to be used in a room

with a volume of less than 36m.

• Steam cleaners must not be used when cleaning this

appliance.

• The performance of your extractor will vary depending

on a number of factors. These include: type of extraction,

length of ducting, room volume, ventilation available and

cleanliness of the ﬁlters.

• The extractor, when extracting air, could generate a

negative pressure in the room which can’t exceed 0.04

mbar. Ensure that there are air intakes allowing a constant

ﬂow of fresh air within the room in which the extractor is

installed. Ventilation for gas fuelled appliances must be as

per regulations in force.

Using your extractor

For best performance, you should switch on the extractor 15 minutes

before starting to cook and leave it to run for approximately 15

minutes after the end of cooking (you can use the timer function for

this).

1 - On/o button

2 - Speed increase button

3 - Speed decrease button

4 - Light button

Switching the extractor on/o and setting the speed level

- Press the on/o button. The appliance will switch on at speed level 1.

- To increase the speed level touch the speed increase button. Red

LED indicators will illuminate according to the set speed.

- To reduce the speed level touch the speed decrease button.

- To switch the extractor o, touch the on/o button.

Extractor lights

- To switch the lights on and o, press button 4 on the remote control.

Please note: The lights are not intended to provide downlight

illumination.

Fig. 1

Timer

The extractor is equipped with a timer that allows the extractor to run

for 15 minutes before switching o automatically.

- To activate the timer, set the desired speed and then press and

hold the speed decrease button (3) for approximately two seconds.

The LED indicator for the speed on the extractor body will ﬂash to

conﬁrm the timer is active.

- To cancel the timer, press either the speed increase button, speed

decrease button or the on/o button.

Please note: The timer can be activated on any speed.

Care and maintenance

IMPORTANT: DO NOT PERFORM MAINTENANCE OR ATTEMPT

TO CLEAN THE EXTRACTOR WITHOUT FIRST SWITCHING OFF

THE ELECTRICITY SUPPLY. ALWAYS WEAR ADEQUATE PPE

(PERSONAL PROTECTIVE EQUIPMENT) FOR THE TASK AT HAND.

Cleaning

You should use a non-abrasive cleaner. Any abrasive cleaner

(including Cif) will scratch the surface and could erase the control

panel markings.

You can clean your extractor eectively by using a dilute solution of

water and mild detergent and drying to a shine with a clean cloth.

IMPORTANT:

Always protect surfaces immediately beneath the extractor (such

as a hob) with clean, dry towels or similar cushioning items before

carrying out any cleaning or maintenance in case of falling parts/

items.

Cleaning the grease ﬁlters

The grease ﬁlters should be kept clean to minimise the risk of ﬁre.

At least once a month you should remove and clean the grease

ﬁlters with hot soapy water. You can also wash the grease ﬁlters in

a dishwasher, ensuring that you place them in an upright position to

prevent damage from other items in the dishwasher. After rinsing and

drying, replace the ﬁlters. Please note that washing the ﬁlters in a

dishwasher can lead to discolouration. This is not a fault.

To remove the grease ﬁlters follow these steps:

1. Open the cover panel by pulling down on the LED indicator side.

The panel will lower as far as the hydraulic arms permit.

2. Pull down the handle on each grease ﬁlter. It will release at the

handle side. Then, lower the grease ﬁlter to remove it completely.

Please note: Releasing the grease ﬁlters, when the extractor is

installed, could cause them to fall. Take care and ensure you remove

them safely. Protect any surfaces below accordingly.

To replace the grease ﬁlters, repeat the above steps in reverse.

This appliance is ﬁtted with energy saving LED lighting that has a

considerably longer life expectancy than traditional ﬁlament bulbs.

These are not user-replaceable. In the unlikely event of a failure

please contact CDA Customer Care using the details on page 17.

The lighting is designed for aesthetic purposes and not for general

room, nor down-light, illumination. Extended use of the lights can

reduce their life span.

Installation preparation

When installing this product we recommend you seek the help of

at least two other individuals. This product may have some sharp

edges. Please take care and wear adequate PPE (Personal Protective

Equipment) when handling.

Installation preparation - height

IMPORTANT:

When the extractor is to be installed above a CDA electric hob, the

minimum distance between the hob and the downwards-facing side

of the extractor must exceed 650mm.

When the extractor is to be installed above a CDA gas hob, the

minimum distance between the hob and the downwards-facing side

of the extractor must exceed 650mm.

If the instructions provided with your gas hob state that the

required distance between the hob and extractor must be greater

than our measurement, then that is the distance that should be

observed; this is a legal requirement and may lead to your hob

being disconnected from the gas supply and the installation being

reported under RIDDOR (the height should be measured from the

top of the burners).

IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH A GAS

HOB, THE MINIMUM DISTANCE BETWEEN THE HOB AND

EXTRACTOR MUST BE AT LEAST 760mm. The width of a hob must

not be greater than the width of the extractor installed above it.

Tabla de contenidos

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario