CDA ECNK90 Guía de inicio rápido
www.cda.eu
ECNK90
Island Extractor
Installation, use and maintenance
2
Contents:
3 Important information
5 Important safety warnings
6 Using your extractor
7 Care and maintenance
8 Changing the charcoal filter
9 Changing a light bulb (contact CDA Customer Care)
10 Mains electricity connection
11 Electrical information
11 Troubleshooting
12 Installation - preparation
13 Ducting
14 Installation
17 Installation height diagrams
19 Energy eciency information
3
Important
The CDA Group Ltd. cannot be held responsible for injuries
or losses caused by incorrect use or installation of this
product. Please note that The CDA Group Ltd. reserves the
right to invalidate the guarantee supplied with this product
following incorrect installation or misuse of the appliance or
use in a commercial environment.
This appliance is not designed to be used by people
(including children) with reduced physical, sensorial or
mental capacity, or who lack experience or knowledge
about it, unless they have had supervision or instructions on
how to use the appliance by someone who is responsible
for their safety.
Under no circumstances should any external covers be
removed for servicing or maintenance except by suitably
qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault
with your appliance and to register your appliance for guarantee
purposes.
Appliance Model
Serial Number
4
EU Declarations of Conformity:
This appliance has been manufactured to the strictest standards and
complies with all applicable legislation, including Gas safety, Electrical
safety (LVD) and Electromagnetic interference compatibility (EMC).
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2012/19/EU.
At the end of its working life, the product must be taken to a special
local authority waste collection centre or to a dealer providing appliance
recycling services. Disposing of a household appliance separately
avoids possible negative consequences for the environment and
health. It also enables the constituent materials to be recovered, saving
both energy and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a crossed-
out wheeled dustbin.
5
Please note:
•Under no circumstances should the extractor be
connected to any gas ventilation system, flue system or
hot air ducting system.
•Do not vent the extractor into an attic or loft space.
•Only house the extractor in rooms with adequate
ventilation. Remember that the extractor is powerful and
whatever air is extracted needs to be replaced.
•Do not tile the extractor in. It should be removable for
service or maintenance.
•Do not use silicone sealant to secure the hood to the
wall.
•You must be able to isolate the extractor from the mains
electrical supply after installation.
•Steam cleaners must not be used when cleaning this
appliance.
•The performance of your extractor will vary depending
on a number of factors. These include: type of extraction,
length of ducting, room volume, ventilation available and
cleanliness of the filters.
6
Using your extractor
For best performance, you should switch on the extractor
15 minutes before starting to cook and leave it to run for
approximately 15 minutes after the end of cooking.
Control Panel
A - Power o button
B - Speed level buttons
C - Light button
To switch the extractor light on or o
• Press button “C”.
To switch on the extractor or to change the speed at any time
when the extractor is running
• Press the relevant “B” button for the first, second or third speed
level as required.
To switch the extractor o
• Press the “A” button.
Important: The lighting is intended to be used for the duration of
cooking only. The lighting should not be used for ambient lighting
purposes.
Fig. 1 A B C
7
Care and maintenance
IMPORTANT: DO NOT PERFORM
MAINTENANCE OR CLEANING OF
THE EXTRACTOR WITHOUT FIRST
SWITCHING OFF THE ELECTRICITY
SUPPLY.
Cleaning
You should use a nonabrasive cleaner.
Any abrasive cleaner (including Cif) will
scratch the surface and could erase the control panel markings.
You can clean your extractor eectively by simply using a dilute
solution of water and mild detergent and drying to a shine with a clean
cloth.
Cleaning the grease filter
The grease filter should be kept clean to minimise the risk of fire.
At least once a month, you should remove and clean the grease
filter with hot soapy water. You can also wash the grease filter in
a dishwasher (see note on page 8), ensuring that you place it in
an upright position to prevent damage from other items in the
dishwasher. After rinsing and drying, replace the filter.
To remove the grease filter
1. Pull open the handle on the grease filter as shown in fig. 2. It will
release at the handle side.
2. Lower the grease filter to remove it completely.
Fig. 2
8
To replace the grease filter
Repeat the steps on page 7 in reverse order.
Please note: Cleaning the grease filter in a dishwasher may lead to
discolouration. This is normal and does not constitute a fault with the
appliance.
Changing the charcoal filter (re-circulating only)
We recommend protecting any areas below and near the hob before
and during this process to make sure nothing falls and causes
damage.
To attach a new charcoal filter, first remove the grease filter as
described on page 7. Remove any old charcoal filter and then oer
up the magnetic side of the new charcoal filter to the metal extractor
housing/opening (the same that holds the grease filter) so that it
secures into place. Leave the tab on the filter accessible for when you
need to remove it. Then, replace the grease filter.
Charcoal filters are available as an optional accessory from CDA
Customer Care under code CHA12.
9
Changing the light
IMPORTANT: THE LIGHT BULBS SHOULD ONLY BE CHANGED BY
CDA AUTHORISED SERVICE AGENTS. IF ONE OR MORE OF YOUR
BULBS FAIL, CONTACT CDA CUSTOMER CARE TO ARRANGE A
SERVICE VISIT.
DO NOT TOUCH THE LIGHT BULBS IMMEDIATELY AFTER USE AS
THE BULB MAY BE WARM/HOT.
Do not touch bulbs or adjacent areas during or straight after pro-
longed use of the lights.
The light is designed for use during cooking and not for general room
illumination. Extended use of the light can reduce the life span of the
bulb.
10
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
USE A 3 AMP FUSE
Mains electricity
connection
THIS APPLIANCE MUST BE
CONNECTED TO THE MAINS SUPPLY
BY A COMPETENT PERSON, USING
FIXED WIRING VIA A DOUBLE POLE
SWITCHED FUSED SPUR OUTLET
AND PROTECTED BY A 3A FUSE.
The appliance must be connected by a
qualified electrician, who is a member
of the N.I.C.E.I.C. and who will comply with the I.E.T.
and local regulations.
The wires in the mains lead of this appliance are coloured in
accordance with the following code:
BLUE = NEUTRAL, BROWN = LIVE, GREEN+YELLOW = EARTH
As the colours of the wires in the mains lead for the appliance may
not correspond with the coloured markings identifying the terminals
connecting to the fused spur, proceed as follows:
•The wire which is coloured blue must be connected to the terminal
marked N (Neutral), or coloured black.
•The wire which is coloured brown must be connected to the
terminal marked L (Live), or coloured red.
•The wire which is coloured green and yellow must be connected
to the terminal marked E (Earth) or coloured green or green and
yellow.
Tabla de contenidos
Otros manuales de Campana de ventilación de CDA
CDA
CDA EVH9 Manual de usuario
CDA
CDA EVPK90 Hoja de especificaciones
CDA
CDA ECH10 Manual de usuario
CDA
CDA CST6 Manual de usuario
CDA
CDA ECA SERIES Guía de inicio rápido
CDA
CDA CTE Series Manual de referencia
CDA
CDA CHX10 Manual de usuario
CDA
CDA EVM9 Manual de referencia
CDA
CDA A1 Manual de usuario
CDA
CDA ECA Guía de inicio rápido
CDA
CDA EVB9 Manual de usuario
CDA
CDA 3S10BL Guía de inicio rápido
CDA
CDA EZA60BL Guía de inicio rápido
CDA
CDA EVCK4 Manual
CDA
CDA ECNK91 Manual de servicio
CDA
CDA EZTK90BL Guía de inicio rápido
CDA
CDA EDD9BL Manual de referencia
CDA
CDA CPXI9 Manual de referencia
CDA
CDA CST62 Instrucciones de instalación y funcionamiento
CDA
CDA EVS90BL Guía de inicio rápido
