Cabletron Systems HubSTACK SEHI-34 Manual de usuario

SEHI-22, SEHI-24, SEHI-32, AND SEHI-34

10BASE-T INTELLIGENT STACKABLE HUB

USER’S GUIDE

CABLETRON SYSTEMS, P. O. Box 5005, Rochester, NH 03867-0505

The Complete Networking Solution™

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other

information contained in this document without prior notice. The reader should in all

cases consult Cabletron Systems to determine whether any such changes have been

made.

The hardware, firmware, or software described in this manual is subject to change

without notice.

INNOEVENTSHALLCABLETRONSYSTEMSBELIABLEFORANYINCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER

(INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR

RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN

IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE

KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Cabletron Systems, Inc.

P.O. Box 5005, Rochester, NH 03867-0505

Printed in the United States of America

Order Number: 9030916-01 February 94

SPECTRUM

LANVIEW

Remote LANVIEW

,and

HubSTACK

™

aretrademarks

of Cabletron Systems, Inc.

IBM

is a registered trademark of International Business Machines Corporation.

i960

is a registered trademark of Intel Corporation.

DEC

VT200

, and

VT300

are trademarks of Digital Equipment Corporation.

Ethernet

is a trademark of Xerox Corporation.

CompuServe

is a registered trademark of CompuServe, Inc.

Windows

is a registered trademark of Microsoft Corporation.

Printed On Recycled Pa

per

NOTICE

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment uses, generates, and can radiate

radio frequency energy and if not installed in accordance with the operator’s manual,

may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause interference in which case the user will be required

to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly

approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

DOC NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la class A prescrites dans le Règlement

sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

NOTICE

iii

CABLETRON SYSTEMS, INC.

PROGRAM LICENSE AGREEMENT

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc.

(“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron

software program (the “Program”) contained in this package. The Program may be

contained in firmware, chips or other media. BY UTILIZING THE ENCLOSED

PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS

AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF

WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE

TERMSOFTHIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO

THE PLACE OF PURCHASE FOR A FULL REFUND.

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE. Youhave the right touseonly the one (1) copyof the Program provided

in this package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as

permitted by the Copyright Act of the United States or as authorized in writing by

Cabletron.

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or

disassemble the Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed

under the laws and in the state and federal courts of New Hampshire. You accept

the personal jurisdiction and venue of the New Hampshire courts.

NOTICE

EXCLUSION OF WARRANTY

AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by

Cabletron in writing, Cabletron makes no warranty, expressed or implied,

concerning the Program (including Its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE

SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF

MERCHANTABLITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH

RESPECTTO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS,

AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS

OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS

INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE

DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO

USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY

FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION

OR LIMITATION OF IMPLIED WARRANTEES IN SOME INSTANCES THE

ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

UNITED STATES GOVERNMENT

RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted

computer software” submitted with restricted rights in accordance with Section 52227-

19 (a) through (d) of the Commercial Computer Software - Restricted Rights Clause and

its successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its

suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as

defined in the DoD Supplement to the Federal Acquisition Regulations, Section 52.227-

7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the Government is

subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical

Data and Computer Software clause at 252.227-7013. Cabletron Systems, Inc., 35

Industrial Way. Rochester, New Hampshire 03867

CONTENTS

TABLE OF CONTENTS

APPENDIX A TABLE OF CONTENTS v

CHAPTER 1 INTRODUCTION

1.1 USING THIS MANUAL............................................................1-1

1.2 GETTING HELP........................................................................1-2

1.3 SEHI OVERVIEW .....................................................................1-2

1.4 SEHI FEATURES......................................................................1-3

1.5 STACKABLE CAPABILITIES..................................................1-4

1.6 REMOTE NETWORK MANAGEMENT CAPABILITIES ......1-4

1.7 OPTIONAL FEATURES ...........................................................1-5

1.8 RELATED MANUALS ..............................................................1-6

CHAPTER 2 INSTALLATION

REQUIREMENTS/SPECIFICATIONS

2.1 CABLE SPECIFICATIONS.......................................................2-1

2.1.1 HubSTACK Interconnect Cable Requirements...........2-1

2.1.2 UTP and STP Cable Specifications for the Network Ports

and EPIM-T Module......................................................2-2

2.1.3 Multimode Fiber Optic Cable Specifications for the

EPIM-F1 and EPIM-F2 Modules .................................2-4

2.1.4 Single Mode Fiber Optic Cable Specifications for

the EPIM-F3 Module ....................................................2-5

2.1.5 Thin-Net Network Requirements for the EPIM-C Mod-

ule 2-6

2.1.6 AUI Cable Requirements for the EPIM-A

and EPIM-X Modules....................................................2-7

2.2 NETWORK PORT SPECIFICATIONS ....................................2-7

2.2.1 SEHI-22 and SEHI-24 Network Port Specifications...2-8

2.2.2 SEHI-32 and SEHI-34 Network Port Specifications...2-8

2.3 EPIM SPECIFICATIONS .......................................................2-10

2.3.1 EPIM-T........................................................................2-10

2.3.2

EPIM-F1 and EPIM-F2.............................................2-11

2.3.3 EPIM-F3......................................................................2-12

2.3.4 EPIM-C........................................................................2-14

2.3.5 EPIM-A and EPIM-X (AUI Port)................................2-15

2.4 COM PORT REQUIREMENTS ..............................................2-16

2.5 TRANSCEIVER REQUIREMENTS.......................................2-16

CONTENTS

2.6 OPERATING SPECIFICATIONS...........................................2-17

CHAPTER 3 INSTALLATION

3.1 UNPACKING THE SEHI ..........................................................3-1

3.2 INSTALLING THE SEHI..........................................................3-1

3.2.1 Stacking the SEHI.........................................................3-2

3.2.2 Attaching the Strain Relief Bracket.............................3-4

3.2.3 Rack Mounting the SEHI..............................................3-5

3.2.4 Wall Mounting the SEHI ..............................................3-6

3.2.5 Free-Standing Installation............................................3-7

3.3 CONNECTING THE SEHI TO THE POWER SOURCE.........3-8

CHAPTER 4 CONNECTING TO THE NETWORK

4.1 CONNECTING THE SEHI TO THE NETWORK....................4-1

4.1.1 Connecting to Network Ports, SEHI-22 and SEHI-24 4-1

4.1.2 Connecting to Network Ports, SEHI-32 and SEHI-34 4-3

4.1.3 Connecting a UTP Segment to an EPIM-T..................4-4

4.1.4 Connecting a Fiber Optic Link Segment to an EPIM-F1,

EPIM-F2, or EPIM-F34-5

4.1.5 Connecting a Thin-Net Segment to an EPIM-C ..........4-8

4.1.6 Connecting an AUI Cable to an EPIM-A ...................4-10

4.1.7 Connecting an AUI Cable to an EPIM-X....................4-11

4.2 FINISHING THE INSTALLATION........................................4-12

CHAPTER 5 TROUBLESHOOTING

5.1 INSTALLATION CHECK-OUT ................................................5-1

5.2 USING LANVIEW......................................................................5-2

5.3 USING THE RESET BUTTON.................................................5-4

CHAPTER 6 LOCAL MANAGEMENT

6.1 MANAGEMENT TERMINAL REQUIREMENTS...................6-2

6.1.1 Console Cable Configuration ........................................6-3

6.1.2 Management Terminal Setup Parameters...................6-4

6.2 ACCESSING LOCAL MANAGEMENT....................................6-5

6.3 USING THE LOCAL MANAGEMENT SCREENS..................6-7

6.3.1 The Community Name Table Screen............................6-7

6.3.2 The Configuration Screen...........................................6-10

6.3.3 The Trap Table Screen................................................6-14

6.3.4 The SNMP Tools Screen..............................................6-16

6.3.5 The Device Statistics Screen.......................................6-22

CONTENTS

vii

APPENDIX B TWISTED PAIR WIRING TABLES A-1

INTRODUCTION

Page 1-1

CHAPTER 1

INTRODUCTION

Welcome to the Cabletron Systems

SEHI-22, SEHI-24, SEHI-32,

and SEHI-34 10BASE-T Intelligent Stackable Hub User’s

Guide

. This manual explains installation instructions and provides

reference information for the SEHI-22, 24, 32, and 34.

Note

: The term SEHI (Stackable Ethernet Hub with Intelligence) is

used throughout this manual when describing features and functions

that are common to the SEHI-22, 24, 32, and 34.

1.1 USING THIS MANUAL

Read through this manual to gain an understanding of the features

and capabilities of the SEHI.A general knowledge of Ethernet and

IEEE 802.3 type data communications networks and their physical

layer components will be helpful when installing the SEHI.

Chapter 1,

Introduction

,outlines the contents of this manual, brieﬂy

describes SEHI features, and concludes with a list of related manuals.

Chapter 2,

Installation Requirements/Speciﬁcations

, describes

installation requirements, network guidelines, and SEHI operating

speciﬁcations.

Chapter 3,

Installation

, contains instructions for installing your

SEHI as a stackable or stand-alone hub.

Chapter 4,

Connecting to the Network

,explains how to connect the

SEHI to the network using the various media types.

Chapter 5,

Troubleshooting,

describes how to use the LANVIEW

LEDs to troubleshoot network problems.

Chapter 6,

Local Management

, describes how to use SEHI Local

Management screens and the available commands.

Appendix A,

Twisted Pair Wiring

Tables

, lists Punch Down Block

pinouts.

INTRODUCTION

Page 1-2

1.2 GETTING HELP

If you need additional support related to the Cabletron Systems SEHI,

or if you have any questions,comments,or suggestions concerning this

manual, contact Cabletron Systems Technical Support:

By phone..................(603) 332-9400

Monday-Friday; 8am - 8pm EST

By CompuServe

.....GO CTRON from any ! prompt

By Internet mail......[email protected]

By FTP.....................ctron.com (134.141.197.25)

anonymous

, Password:

your email address

1.3 SEHI OVERVIEW

The 10BASE-T SEHI is an intelligent repeating hub that provides

front panel ports for network connections and a rear panel

HubSTACK Interconnect Bus port for stackable connections.The

SEHI is designed to manage Cabletron Systems’ SEH series of

non-intelligent stackable hubs.

Figure 1-1. The SEHI-24 and SEHI-34

SEH INTERCONNECT

OUT

SEHI-24

10BASE-T HUB

WITH

LANVIEW®

EPIM-1

EPIM-2

PWR

CPU

CLN E

RCV

LNK

RCV

LNK

HubSTACK

10BASE-T HUB

WITH

LANVIEW®

SEHI-24

24X 23X 22X 21X 20X 19X 18X 17X 16X 15X 14X 13X

12X 11X 10X 9X 8X 7X 6X 5X 4X 3X 2X 1X

COM

RESET

24 23 22 21 20 19 18 17 16 15 14 13

12 11 10 9 8 7 6 5 4 3 2 1

SEH INTERCONNECT

OUT

SEHI-34

10BASE-T HUB

WITH

LANVIEW®

EPIM-1

EPIM-2

PWR

CPU

CLN E

RCV

LNK

RCV

LNK

HubSTACK

10BASE-T HUB

WITH

LANVIEW®

SEHI-34

COM

RESET

24 23 22 21 20 19 18 17 16 15 14 13

12 11 10 9 8 7 6 5 4 3 2 1

12X 1X

24X 13X

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Cabletron Systems

Cabletron Systems

Cabletron Systems MMAC-Plus 9T122-24 Manual de usuario

Cabletron Systems

Cabletron Systems SmartCell 6A000 Manual de usuario

Cabletron Systems

Cabletron Systems SmartCell 6A000 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 8000 Manual de usuario

Cabletron Systems

Cabletron Systems FRM Manual de usuario

Cabletron Systems

Cabletron Systems STH 24 STH-24 Manual de usuario

Cabletron Systems

Cabletron Systems SMALL OFFICE CyberSwitch 150 Manual de usuario

Cabletron Systems

Cabletron Systems DLE22-MA Manual de usuario

Cabletron Systems

Cabletron Systems FN100 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-16TX Manual de usuario

Cabletron Systems

Cabletron Systems MiniMMAC Manual de usuario

Cabletron Systems

Cabletron Systems FN100 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-18 Manual de usuario

Cabletron Systems

Cabletron Systems SEHI SEHI100TX- Manual de usuario

Cabletron Systems

Cabletron Systems 2H28-08R Manual de usuario

Cabletron Systems

Cabletron Systems SEHI-22 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9E312-12 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9H421-12 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch SBU128 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9G426-02 Manual de usuario

Cabletron Systems

Cabletron Systems Cabletron CyberSWITCH CSX5500 Manual de instrucciones

Cabletron Systems

Cabletron Systems TRXI-22 Manual de usuario

Cabletron Systems

Cabletron Systems 6A000/ZX-250 Manual de usuario

Cabletron Systems

Cabletron Systems TRFMIM 28 TRFMIM-28 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario