Burkert PTB 07 ATEX 2063 X Manual de usuario
Operating Instructions
Bedienungsanleitung
Instructions de Service
PTB 07 ATEX 2063 X
Magnetspule Typ AC19
Geräte mit II 2G Ex m Zulassung
Device with II 2G Ex m approval
Appareils avec mode de protection II 2G Ex m
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© Bürkert Werke GmbH & Co. KG, 2008 - 2017
Operating Instructions 1805/01_EU-EN_00806067 / Original DE
3
Table of Contents:
1. OPERATING INSTRUCTIONS ...................................................................4
1.1. Symbols ..............................................................................................4
2. INTENDED USE ................................................................................................5
2.1. Restrictions ........................................................................................5
3. GENERAL SAFETY INSTRUCTIONS .....................................................6
4. GENERAL INFORMATION ...........................................................................7
4.1. Contact addresses ..........................................................................7
4.2. Warranty .............................................................................................8
4.3. Approval .............................................................................................8
4.4. Information on the Internet .............................................................8
5. APPLICATION CONDITIONS ....................................................................8
5.1. Special conditions ...........................................................................8
5.2. Operating Conditions ......................................................................9
5.3. Installation conditions ....................................................................10
5.4. Application in petrol pumps .........................................................10
6. TECHNICAL DATA ........................................................................................ 11
7. INSTALLATION ..............................................................................................12
7.1. Safety Instructions .........................................................................12
7.2. Installation ........................................................................................13
7.3. Electrical connection .....................................................................14
8. START-UP .........................................................................................................14
8.1. Safety Instructions .........................................................................14
9. MAINTENANCE AND REPAIRS .............................................................15
9.1. Maintenance ....................................................................................15
9.2. Repairs ..............................................................................................15
9.3. Troubleshooting ..............................................................................15
10. TRANSPORT, STORAGE, DISPOSAL ..............................................15
Solenoid coil AC19, device with II 2G Ex m approval
english
07 ATEX 2063 X
4
Operating instructions
WARNING!
Warns of a potentially dangerous situation!
• Failure to observe the warning may result in serious injuries or
death.
CAUTION!
Warns of a possible danger!
• Failure to observe the warning may result in moderately serious
or minor injuries.
NOTE!
Warns of damage to property!
designates additional significant information, tips and
recommendations.
refers to information in these operating instructions or in
other documentation.
→designates a procedure which you must carry out.
1. OPERATING INSTRUCTIONS
The operating instructions describe the entire life cycle of the device.
Keep these instructions in a location which is easily accessible to
every user and make these instructions available to every new owner
of the device.
WARNING!
The operating instructions contain important safety
information!
Failure to observe these instructions may result in hazardous
situations. The operating instructions must be read and
understood.
• Carefully read the operating instructions before using the device.
• In particular observe the chapter entitled "Intended use", and
"General safety instructions" as well as the chapter entitled
"Application conditions of the coil AC19".
1.1. Symbols
To identify important information, the following symbols are used in
the operating instructions:
DANGER!
Warns of an immediate danger!
• Failure to observe the warning may result in a fatal or serious
injury.
english
07 ATEX 2063 X
5
Intended Use
2. INTENDED USE
WARNING!
Incorrect use of the coil AC19 can be dangerous to people,
nearby equipment and the environment.
• The solenoid coil AC19 is used to actuate valves which control
gaseous or liquid media. It was designed for use in explosion
group II, category 2D, Ex mbD, IP64, T130°C and in explosion
group II, category 2G and temperature class T4 (see specifica-
tions on the - approval plate).
• The coil AC19 is always attached to the core feed pipe of the
valve fitting and secured with a nut. In this way coil and valve
body are connected in such a way that a closed system is for-
med which may also be used as a category 2 device to control
petrol in petrol pumps. For this application a valve body made of
metal (brass, aluminium or stainless steel) must be used.
When using the device, observe the permitted data, operating
conditions and application conditions which
– are specified in the operating instructions for the solenoid coil
AC19, on the rating plate, in the contract documents
– as well as in the operating instructions for the solenoid valve
actuated with the coil.
The coil may be used only in conjunction with third-party devices
and components recommended and authorised by Bürkert.
Correct transportation, correct storage and installation and careful
use and maintenance are essential for reliable and problem-free
operation.
• Any other use is considered improper use.Bürkert is not liable
for any resulting damage. The user alone bears the risk.
• Use the device only as intended.
2.1. Restrictions
If exporting the system/device, observe any existing restrictions.
2.1.1. Explosion protection approval
The explosion protection approval is only valid if you use the modules
and components authorised by Bürkert, as described in these ope-
rating instructions.
The coil AC19 may be used only in combination with the valve types
released by Bürkert, otherwise the explosion protection approval will
be terminated!
If you make unauthorised changes to the system, the modules or com-
ponents, the explosion protection approval will be terminated.
english
07 ATEX 2063 X
6
General Safety Instructions
3. GENERAL SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any
• contingencies and events which may arise during the installation,
operation and maintenance of the devices.
• local safety regulations, whereby the operator is responsible for their
compliance, by the installation personnel too.
DANGER!
Danger of explosion!
Following installation, solenoid coil and valve body form a closed
system. If used in the EX area, there is a danger of explosion if the
system is opened during operation!
• The system must not be disassembled during operation.
Danger of explosion caused by electrostatic charge!
If there is a sudden discharge from electrostatically charged devices
or persons, there is a danger of explosion in the EX area.
• Take appropriate measures to prevent electrostatic charges in the
EX area.
• Clean the device surface of the solenoid valve by gently wiping
it with a damp cloth
DANGER!
Risk of electric shock!
There is a serious risk of injury when reaching into the equipment.
• Only trained electrical engineers may work on the electrical
system.
• Before starting work, always switch off the power supply and
safeguard to prevent re-activation!
• Observe applicable accident prevention and safety regulations
for electrical equipment!
Danger of burns/danger of fire during long-term operation!
The solenoid coil may become very hot during long-term operation.
• Take hold of a device which has been running for a prolonged
period with protective gloves only.
Danger – high pressure!
There is a serious risk of injury when reaching into the system.
• Only skilled and instructed personnel may work on the system
with suitable tools.
• Before disconnecting lines and valves, switch off the pressure
and bleed the lines.
• During installation note the direction of flow.
• Observe applicable accident prevention and safety regulations
for pressurised devices!
• After an interruption in the power supply or fluid supply, ensure
that the process is restarted in a defined or controlled manner!
english
07 ATEX 2063 X
7
General Information
WARNING!
General hazards!
• Do not use the valve fitting or the complete device as a lever to
screw the valve into the line system.
• Do not put any loads on the housing (e.g. by placing objects on
it or standing on it).
• Do not make any external modifications to the device housings.
Do not paint the housing parts or screws.
Unintentional activation or unauthorised impairment of the system
may cause general hazardous situations through to physical injury.
• Take appropriate measures to prevent the system from being
accidentally actuated!
• Do not make any unauthorised changes to the system.
Non-observance of the generally acknowledged safety rules may
cause general hazardous situations through to physical injury.
• Observe the generally acknowledged safety rules for resource
planning and operation of the coil AC19 and the associated
solenoid valve.
Operate the coil AC19 and the associated solenoid valve in
perfect working order only and in accordance with the operating
instructions.
4. GENERAL INFORMATION
4.1. Contact addresses
Germany
Bürkert Fluid Control Systems
Sales Center
Christian-Bürkert-Str. 13-17
D-74653 Ingelfingen
Tel. + 49 (0) 7940 - 10 91 111
Fax + 49 (0) 7940 - 10 91 448
E-mail: [email protected]
International
Contact addresses can be found on the final pages of the printed
operating instructions.
And also on the Internet at:
www.burkert.com
english
07 ATEX 2063 X
8
Application conditions
4.2. Warranty
The warranty is only valid if the device is used as intended in accordance
with the specified application conditions.
4.3. Approval
The EC Type Examination Certificate PTB 07 ATEX 2063 X was
issued by the
PTB (Physikalisch Technische Bundesanstalt)
Bundesallee 100
38116 Braunschweig (Germany)
which also audits production (CE0102).
4.4. Information on the Internet
The operating instructions and data sheets for Bürkert products can
be found on the Internet at:
www.burkert.com
5. APPLICATION CONDITIONS
5.1. Special conditions
5.1.1. Short-circuit protection
To protect each solenoid against short-circuit, a fuse (max. 3 x Ib in
accordance with IEC 60127-2-1), corresponding to the rated current,
or a motor protection switch with short-circuit and thermal quick release
(set to rated current) must be connected upstream.
• At very low rated currents of the solenoid the fuse with the lowest
current value is adequate according to the stated IEC standard.
This fuse may be housed in the associated supply unit or must be
connected separately upstream.
• The fuse rated voltage must be the same or higher than the indicated
nominal voltage of the solenoid.
• The interruption rating of the fuse link must be the same or higher than
the maximum short-circuit current to be accepted at the installation
site (usually 1500 A).
Example 2/2-way
solenoid valve:
Solenoid coil AC19
Valve body
The nominal value of
the fuse is indicated
on the solenoid
Fuse
F . , . . A
Fig. 1 : Example of coil AC19 as part of a closed system.
english
07 ATEX 2063 X
9
Application conditions
5.2. Operating Conditions
For operation of the solenoid coils Type AC19-..-.-PF09 and Type
AC19-..-.-PF10 observe the following requirements.
5.2.1. Materials
For the selection of materials for the system observe the application-
specific, safety requirements.
Valve body:
DANGER!
Danger of explosion!
If the system is used as a category 2 device, only valve bodies
made of metal can ensure the required safety for the control of
petrol in petrol pumps!
• Use only valve bodies made of metal (brass, aluminium or
stainless steel) for the control of petrol in petrol pumps with
category 2 devices.
• For use in petrol pumps
Metal (brass, aluminium, stainless steel)
• Other applications
Metal (brass, aluminium, stainless steel) or plastic (e.g. polyamide
PA 6 GV ...)
Sheathing of the electrical connection cables:
Type AC19-..-.-PF09 PVC
Type AC19-..-.-PF10 PUR
5.2.2. Minimum dimensions
Valve body:
55 mm x 36 mm x 30 mm (L x W x H)
A larger valve body with improved thermal conductivity may be
used at any time.
5.2.3. Application temperature range:
DANGER!
Danger of explosion!
If the max. permitted temperature values for the coil AC19 are
exceeded, there is a danger of explosion.
• Observe the temperature specifications for the coil
• Observe any restrictions by the max. permitted values for the
solenoid valve combined with the coil.
Temperature values of the solenoid coil AC19
Maximum surface temperatur of the coil at 60 °C ambient tempe-
rature and nominal voltage: 110 °C (for gas)
130 °C (for dust)
Temperature class (for gas) T4
Max. permitted ambient temperatures
Type Material of the electrical
connection cables
Max. permitted
ambient temperature
AC19-..-.-PF09 PVC -40 – +55 °C
AC19-..-.-PF10 PUR -40 – +60 °C
english
07 ATEX 2063 X
10
Application conditions
5.3. Installation conditions
The solenoid coils Type AC19-..-.-PF09 to Type AC19-..-.-PF10 are
suitable for single installation only.
The connection cables must be laid permanently to protect against
damage.
Also observe the specifications in the chapter entitled
"Technical Data".
5.4. Application in petrol pumps
DANGER!
Danger of explosion!
Following installation, solenoid coil and valve body form a closed
system. If used in the EX area, there is a danger of explosion if the
system is opened during operation!
• The system must not be disassembled during operation.
• The valve body may be repaired by the manufacturer only.
Solenoid valves together with the coil AC19 may be used as
category 2 devices only for the control of petrol if there is no air
and no oxygen in the closed system.
• Ensure that the closed system contains no air or oxygen or
cannot be penetrated by air or oxygen.
• When switching off or starting up the system, ensure that nei-
ther air nor oxygen has penetrated the system.
If the system is used as a category 2 device, only valve bodies
made of metal can ensure the required safety for the control of
petrol in petrol pumps!
• Use only valve bodies made of metal (brass, aluminium or
stainless steel) for the control of petrol in petrol pumps with
category 2 devices.
Example: 2/2-way solenoid valve
Solenoid coil AC19
Valve body
Fig. 2 : Example of coil AC19 as part of a closed system.
english
07 ATEX 2063 X
Tabla de contenidos
Idiomas:
Otros manuales de Unidad de control de Burkert
Burkert
Burkert 5470 Manual de usuario
Burkert
Burkert 8653 AirLINE Field Manual de usuario
Burkert
Burkert Robolux 2036 Manual de usuario
Burkert
Burkert 2060 Manual de usuario
Burkert
Burkert 6520 NARMUR Manual de usuario
Burkert
Burkert 2101 Manual de usuario
Burkert
Burkert 3323 Manual de usuario
Burkert
Burkert 6027 Manual de usuario
Burkert
Burkert 6628 Manual de usuario
Burkert
Burkert 2103 Series Manual de usuario
Burkert
Burkert 2012 Manual de usuario
Burkert
Burkert 2101 Manual de usuario
Burkert
Burkert 85343 Manual de usuario
Burkert
Burkert 6020 Manual de usuario
Burkert
Burkert 8695 Manual de usuario
Burkert
Burkert 2000 INOX Manual de usuario
Burkert
Burkert ACP016 Series Manual de usuario
Burkert
Burkert Type 2000 Manual de usuario
Burkert
Burkert 2060 Manual de usuario
Burkert
Burkert 2712 Series Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
