Burkert 0340 Manual de usuario
Bedienungsanleitung
Manuel d‘utilisation
Operating Instructions
Type 0340, 0343, 0344
3/2-way solenoid valve
3/2-Wege-Magnetventil
Électrovanne 3/2 voies
2
1 OPERATING INSTRUCTIONS
The operating instructions contain important information.
▶Read the operating instructions carefully and follow the safety instruc-
tions in particular, and also observe the operating conditions.
▶Operating instructions must be available to each user.
▶The liability and warranty for the product / device are void if the operat-
ing instructions are not followed.
1.1 Symbols
▶Designates an instruction to prevent risks.
→designates a procedure which you must carry out.
Warning of injuries:
DANGER!
Imminent danger! Serious or fatal injuries.
WARNING!
Potential danger! Serious or fatal injuries.
CAUTION!
Danger! Minor or moderately severe injuries.
Warns of damage to property:
NOTE!
2 INTENDED USE
Incorrect use of the solenoid valve Type 0340, 0343 and 0344 can
be dangerous to people, nearby equipment and the environment.
▶The device is designed to control, shut off and meter neutral media.
▶Provided the cable plug is connected and installed correctly, e.g. Bürk-
ert Type 2508, the device satisfies protection class IP65 in accordance
with DIN EN 60529 / IEC 60529.
▶Use according to the permitted data, operating conditions and con-
ditions of use specified in the contract documents and operating
instructions.
▶Correct transportation, correct storage and installation and careful use
and maintenance are essential for reliable and problem-free operation.
▶Use the device only as intended.
2.1 Definition of term
In these operating instructions, the term “device” always refers to the
Type 0340, 0343 and 0344.
english
3
Risk of injury due to malfunction of valves with alternating
current (AC)!
Sticking core causes coil to overheat, resulting in a malfunction.
▶Monitor process to ensure function is in perfect working order.
Risk of short-circuit/escape of media through leaking screw joints!
▶Ensure seals are seated correctly.
▶Carefully screw together coil and cable plug or valve and connection
plate.
To prevent injury, ensure that:
▶Do not make any internal or external changes to the device bodies.
Ensure that the system cannot be activated unintentionally.
▶Installation and repair work may be carried out by authorized techni-
cians only and with the appropriate tools.
▶After an interruption in the power supply or pneumatic supply, ensure
that the process is restarted in a defined or controlled manner.
▶For models with ATEX or UL approval follow the safety instructions
on the respective supplementary sheet.
3 BASIC SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any contin-
gencies and events which may arise during installation, operation and
maintenance.
Danger – high pressure!
▶Before loosening the lines and valves, turn off the pressure and
vent the lines.
Risk of electric shock!
▶Before reaching into the system, switch off the power supply and
secure to prevent reactivation!
▶Observe applicable accident prevention and safety regulations for
electrical equipment!
Risk of burns/Risk of fire if used continuously through hot device
surface!
▶Keep the device away from highly flammable substances and media
and do not touch with bare hands.
english
4
▶Do not put any loads on the body.
▶The general rules of technology apply to application planning and
operation of the device.
3.1 Warranty
The warranty is only valid if the device is used as intended in accordance
with the specified application conditions.
3.2 Information on the internet
The operating instructions and data sheets for type 0340, 0343 and 0344
can be found on the internet at:
www.buerkert.com Type 0340, 0343, 0344
4 TECHNICAL DATA
4.1 Operating conditions
The following values are indicated on the type label:
• Voltage (Tolerance ± 10 %) / Current type
• Coil power consumption (active power in W - at operating temp.)
• Pressure range1)
• Body material: Brass (MS)
• Seal material: NBR
Operating principle 3/2-way valve Type 0340 and 0344:
Standard Version
C
(NC)
A
PR
D
(NO)
B
PR
Impulse Version
C
(NC)
A
PR
1
2
3D
(NO)
B
PR
1
2
3
→Type 0344: Connect vacuum pump to connection R.
english
5
Operating principle 3/2-way valve Type 0343:
Standard Version
C
(NC)
A
PR
Continuity A → R normally open,
connect vacuum generator to R,
external air to P, auxiliary control air to Z
D
(NO)
B
PR
Continuity P → B normally open,
connect vacuum generator to R,
external air to P, auxiliary control air to Z
1)
The externally controlled valve, Type 0343, requires auxiliary control air which
is at least 2 bar above operating pressure
Protection class: IP65 in accordance with DIN EN 60529 /
IEC 60529 with cable plug, e. g. Bürkert
Type 2508
4.2 Application conditions
Ambient temperature: 0 °C ... +55 °C
Medium temperature: 0 °C ... +90 °C
The following values must also be observed for valves with
UL/UR approval:
Valve
type
Seal
material
Orifice
Valve
seat
[mm]
Fluid
temperature
°F / °C
Ambient
temperature
°F / °C
Fluid
(non-
hazardous
Fluids)
0340 EPDM 12.0 -4...+194 °F
-20...+90 °C
-4...+131 °F
-20...+55 °C
dry air,
inert gas
+41...+194 °F
+5...+90 °C
+41...+131 °F
+5...+55 °C
water
NBR 8.0
12.0
20.0
25.0
+32...+194 °F
0...+90 °C
+32...+131 °F
0...+55 °C
dry air,
inert gas
+41...+194 °F
+5...+90 °C
+41...+131 °F
+5...+55 °C
water
0344
(Vacuum-
version)
NBR 8.0
12.0
20.0
+32...+194 °F
0...+90 °C
+32...+131 °F
0...+55 °C
dry air,
inert gas
Viscosity (Type 0340): 21 mm2/s
english
6
Media
Type 0340: neutral media, compressed air, water,
hydraulic oil
Type 0343 / 0344: neutral gas, compressed air, vacuum
Operating duration: Unless otherwise indicated on the type label,
the solenoid system is suitable for continuous
operation
Important information for functional reliability during continuous
operation! If standstill for a long period at least 1-2 operation
per day are recommended.
Service life: High switching frequency and high pressures
reduce the service life
4.3 Conformity
In accordance with the EC Declaration of conformity, the solenoid valve
Type 0340, 0343 and 0344 is compliant with the EC Directives.
4.4 Standards
The applied standards, which verify conformity with the EC Directives,
can be found on the EC Type Examination Certificate and / or the EC
Declaration of Conformity.
4.5 Type label
Type
Operating
principle
Orifice
Seal material
Body material
Id.- Number
Manufacture-Code
Voltage, Frequency, Power
consumption
Connection thread, Operating
pressure
0340 C 12,0 NBR MS
Made in Germany
00041346 W17MG
230V 50 Hz 8W
G1/2 P
N 0,5
- 1
6 bar
english
7
5 INSTALLATION
5.1 Safety instructions
DANGER!
Risk of injury from high pressure in the equipment!
▶Before loosening the lines and valves, turn off the pressure and
vent the lines.
Risk of injury due to electrical shock!
▶Before reaching into the system, switch off the power supply and
secure to prevent reactivation!
▶Observe applicable accident prevention and safety regulations for
electrical equipment!
WARNING!
Risk of injury from improper installation!
▶Installation may be carried out by authorized technicians only and
with the appropriate tools!
Risk of injury from unintentional activation of the system and an
uncontrolled restart!
▶Secure system from unintentional activation.
▶Following installation, ensure a controlled restart.
5.2 Before installation
Installation position: any, actuator preferably upwards.
Procedure:
→Check pipelines for dirt and clean.
→Install a dirt filter before the valve inlet (≤ 500 µm).
5.3 Installation
NOTE!
Caution risk of breakage!
• Do not use the coil as a lifting arm.
→Hold the device with a open-end wrench on the body and screw
into the pipeline.
Valve body must not be installed under tension.
→Observe pin assignment according to switching function and
identification.
english
8
5.4 Manual emergency actuation
CAUTION!
Discharge of medium due to loss of the O-rings!
▶If the O-rings are lost, the valve will leak. Medium may be discharged.
NOTE!
Caution!
• When the manual emergency actuation is locked, the valve can no
longer be actuated electrically.
Manual emergency
actuation
Press
Turn
1
2
DANGER!
Discharge of medium due to leaking device!
If the O-rings are forgotten or incorrectly inserted during installation
of the pilot valve, the device will be damaged and medium will be
discharged.
▶Before screwing in the pilot valve, correctly insert O-rings into the
depressions.
5.5 Electrical connection of the cable plug
WARNING!
Risk of injury due to electrical shock!
▶Before reaching into the system, switch off the power supply and
secure to prevent reactivation!
▶Observe applicable accident prevention and safety regulations for
electrical equipment!
If the protective conductor contact between the coil and body is
missing, there is danger of electrical shock!
▶Always connect protective conductor.
▶Check electrical continuity between coil and body.
english
9
Procedure:
→Tighten cable plug (for permitted types see data sheet), observing
max. torque 1 Nm.
→Check that seal is fitted correctly.
→Connect protective conductor and check electrical continuity between
coil and body.
Authorized cable plug e.g.
Type 2508 or other suitable
cable plug in accordance with
DIN EN 175301-803 Form A
Seal
max. 1 Nm
5.5.1 Electrical connection - Pulse
DC connections:
Terminal 1 = closed +
Terminal 2 = open +
Terminal 3 = GND -
Terminal 4 = Protective conductor
Protective conductor
connection
24 3
1
The connection terminals in the cable plug are identified with
the numbers 1 to 3 according to the terminals on the valve.
Procedure:
→Connect the pulse valves (variable code CF 02).
→For direct current versions connect negative terminal to terminal 3.
english
10
NOTE!
Important information:
• Avoid emitting pulses simultaneously to both coil windings.
• Do not switch any other consumers (relays, etc.) at the same time
as the terminals.
• The coil connection, to which voltage is not applied, must be galvani-
cally isolated (open).
• If two or more valves are switched in parallel, ensure that this
requirement is met by using 2-pole or multi-pole switches.
6 MAINTENANCE, TROUBLESHOOTING
6.1 Safety instructions
WARNING!
Risk of injury from improper maintenance!
▶Maintenance may be carried out by authorized technicians only and
with the appropriate tools!
Risk of injury from unintentional activation of the system and an
uncontrolled restart!
▶Secure system from unintentional activation.
▶Following maintenance, ensure a controlled restart.
6.2 Malfunctions
Type 0340: Shipment may have caused the position to occupy a
middle position.
Procedure:
→Apply pressure to connection P and briefly seal connection A/B,
→Using your finger, press piston through connection R into the end
position.
english
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Unidad de control de Burkert
Burkert
Burkert PTB 00 ATEX 2129 X Manual de usuario
Burkert
Burkert 3323 Manual de usuario
Burkert
Burkert 2712 Series Manual de usuario
Burkert
Burkert 2100 series Manual de usuario
Burkert
Burkert 6603 Manual de usuario
Burkert
Burkert AirLINE 8652 Manual de usuario
Burkert
Burkert 6106 Manual de usuario
Burkert
Burkert 2012 Manual de usuario
Burkert
Burkert 6516 Manual de usuario
Burkert
Burkert 2030 Manual de usuario
Burkert
Burkert 8690 Manual de usuario
Burkert
Burkert ME44 Manual de usuario
Burkert
Burkert 3360 Manual de usuario
Burkert
Burkert 6027 Manual de usuario
Burkert
Burkert 2031 Manual de usuario
Burkert
Burkert 8681 Manual de usuario
Burkert
Burkert 2064 Manual de usuario
Burkert
Burkert 5281 Series Manual de usuario
Burkert
Burkert 8695 Manual de usuario
Burkert
Burkert 2103 Series Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
