Bristan WMNT12 Instrucciones de montaje

Installation Instructions

& User Guide

Please leave these instructions

with the end user

Maximum Static Pressure: 10.0 bar

Max: 5.0 bar

Hot

Cold

On -

Handset

On -

Prior to Installation Spares

Pack Contents Operation

Dynamic Water Pressure

Speciﬁcations

25°C

5°C

Min 5°C; Max 25°C

Inlet Water Temperature Inlet Connections

Tools Required

All products manufactured and supplied by Bristan are safe to use provided that they are installed,

operated and receive regular maintenance in accordance with these instructions.

This product needs to be installed in accordance with, and meet the requirements of The

Water Supply (Water Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings)

(Scotland) Byelaws 2014. For full Installation Requirements & Notes (IRN) please visit www.wrasapprovals.

co.uk/approvals-directory

Before installing this product the water supply must be thoroughly ﬂushed in order to remove any swarf,

solder etc. Full access must bemade available for future maintenance/servicing purposes. Isolation valves

must be ﬁtted to the inlet water supplies to ensure ease of future maintenance.

Before drilling into walls, check that there are no hidden electrical wires, cables or water supply pipes. This

can be checked with the aid of an electronic detector. If power tools are used do not forget to:

- Wear eye protection - Unplug equipment after use

This product must not be modiﬁed in any way as this will invalidate the guarantee.

Min: 1.0 bar

BUZ2 SHXDIVCTFF C (D5)

65°C

60°C

Recommended 60°C;

Max 65°C

IMPORTANT

The inlet hot water must

be at least 10°C above the

required blend temperature.

Factory

pre-set 38°C

150mm

Centres

1/2”

Compression

Inlet Dimensions

Flat head Screwdriver Cross head Screwdriver Hexagonal Keys Socket SpannerPipe CutterPencil Drill Spanner

1.0

2.0

5.0

4.0

3.0

Pressure

BAR

x2 x2

To replace any spare parts

for your shower, why not

scan the QR Code or visit

www.bristan.com and

search for your product.

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave

them with the user.

Installation Instructions

and User Guide

Bar Showers with Wallmount

12 Fixing Kit (WMNT12)

Contents

• Important Safety Information 3

• Installation Requirements 4-6

• Installation 7

• Isolation 8

• Temperature Setting 8

• General Cleaning 9

• Notes 9

• Maintenance - Cartridege/Valve Cleaning 10

• Troubleshooting 11

2Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Contents

Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have

designed this product with your enjoyment in mind. To ensure that it works to its

full potential, it needs to be ﬁtted correctly. These ﬁtting instructions have been

created to give you all of the information you need and, if you need any further help,

please do not hesitate to give us a call on 0330 026 6273.

Please make sure you read these instructions and retain for future use.

All products manufactured by Bristan are safe, providing they are installed and used

correctly and also receive maintenance when needed.

These ﬁttings, including the connecting water and waste system need to be installed

in accordance with and meet the requirements of the Water Supply Regulations 1999

(Water Fittings) and current by-laws. If you are in doubt about your ability to install

this product correctly or safely, you should employ the services of an experienced

qualiﬁed plumber.

This product must not be modiﬁed in any way otherwise this will invalidate the

guarantee. Remove all packaging and check the contents for damage before starting

installation.

Warning: Before installing the new mixer valve it is essential that you thoroughly

ﬂush through the pipework in order to remove any remaining swarf,

solder, etc. Failure to carry out this procedure could cause problems or

damage to the workings of the mixer tap.

Fitting isolating valves to the inlet feeds is required for ease of maintenance.

Warning: Do not operate the mixer if you suspect it is frozen. Do not site the mixer

valve where it might be subjected to freezing conditions.

Consider the following whilst using power tools:

• Prior to drilling into walls, check there are no hidden electrical cables or

wires and there are also no water pipes. These can potentially be found

using an electrical or metal detector. You may also need to know some

of the schematics of previous installations to determine the suitability

and accommodation of the installation.

• Wear the correct PPE, especially ear, eye and hand protection

when using power tools. Unplug any mains equipment after use.

• Keep electrical equipment away from sources of water.

• If a blow-lamp is used when plumbing, the ﬂame must be kept well away from

the product otherwise damage may occur.

If in doubt, contact a registered plumber, your Local Water Authority or the

Secretary of The Institute of Plumbing, address as follows;-

The Institute of Plumbing,

64 Station Lane,

Hornchurch,

Essex, RM12 6NB

Tel:01708 472791

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Important Safety Information

Please refer to your speciﬁc shower

contents page for speciﬁcation

information.

These showers are designed to be used

in conjunction with the kit supplied, or

Bristan shower kits where not supplied.

We cannot guarantee compatability or

adequate performance when used with

other kits. This would also invalidate your

guarantee. Please refer to the installation

manual supplied with your Bristan

shower kits for their speciﬁcation

information.

This shower valve must be installed

in compliance with current water

regulations. If you have any doubts

about the water regulation requirements

contact your local water services

provider or use the services of a

professional plumber.

This shower valve is suitable for use with

the following water supply systems:

• Gravity Fed Hot and Cold

(pressure imbalance should not exceed

a ratio of 5:1 - see Speciﬁcation section)

• Gravity Fed Hot and Mains Cold

(pressure imbalance should not exceed

a ratio of 5:1 - see Speciﬁcation section)

• Instantaneous water heater

(combination boiler)

• Unvented System

• Pumped System

Important: If you install this shower valve

with a gravity fed system, there must be a

minimum head (vertical distance) from the

underside of the cold water storage tank

to the outlet of at least 1 metre for every

0.1 bar of minimum pressure required.

Note: Pumped system (with Essex ﬂange)

If you install this shower valve to a pumped

gravity fed system where the minimum

head (vertical distance) from the underside

of the cold water storage tank to the top

of the hot water cylinder is less than 1

metre we recommend an Essex ﬂange is

used as shown.

Flushing Pipe-work

Important: Before connecting the shower

valve (see ‘Installation’ on page 7), the

supply pipe-work must be ﬂushed to clear

debris before connecting the shower.

Debris will reduce the performance and life

of the bar shower and Wall Mount.

4Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

Gravity Fed Hot and Cold Gravity Fed Hot and Mains Cold

cold mains supply cold mains supply

1m min.

min.

Key: Isolating

Valve

Reducing

Valve

Shower

Valve Pump Essex

Flange

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

Unvented System

Instantaneous Water Heater

Pumped System

cold mains supply

Pumped System (with Essex ﬂange)

cold mains supply

1m min.1m min.

50mm

If less

than

1m see

note.

Key: Isolating

Valve

Reducing

Valve

Shower

Valve Pump Essex

Flange

6Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

Installation

Identify the

required position of

the valve and prepare

the water supply pipes.

Supply pipes should be

150mm apart.

Using the rubber ﬁxing

plate supplied with the

wall mount, mark and

drill holes.

Secure the isolatorSecure the isolator

onto the backplateonto the backplate

ensuring the olive isensuring the olive is

positioned over thepositioned over the

pipework correctly.pipework correctly.

Push shrouds to thePush shrouds to the

back of the wall outlet,back of the wall outlet,

securing them againstsecuring them against

the rubber ﬁxing plate.the rubber ﬁxing plate.

150mm Centres

Secure the rubber backplateSecure the rubber backplate

and backplate into place.and backplate into place.

Secure the shower toSecure the shower to

the wall mount.the wall mount.

21mm21mm

REMEMBER

To service

your

product!

REMEMBER

hot on the left,

cold on the

right

PLEASE NOTE - Wall Mounts shown in these instructions are for illustration purposes

only. WMNT12 and WMNT12 SQ can be ﬁtted using these instructions.

Now refer to your kit instructions to install your shower kit if supplied. If

your shower is TMV approved, please refer to the TMV manual supplied to

commision your shower.

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

PLEASE NOTE - Wall Mounts shown in these instructions are for illustration purposes

only. WMNT12 and WMNT12 SQ can be ﬁtted following these instructions. Check your

contents page for more details speciﬁc to your shower.

Temperature Setting

Reverse steps 1-2 to

reinstall the cartridge

and handle.

PLEASE NOTE - Bar showers shown in these instructions are

for illustration purposes only. All bar showers can be

ﬁtted/maintained following these instructions. Check your contents

page for more details speciﬁc to your shower.

Turn the temperature handle

to the max. setting and

remove the temperature

handle.

Turn cartridge spindle clockwise

to decrease the temperature.

Turn cartridge spindle

anti-clockwise to increase the

temperature.

IMPORTANT

TMV showers are pre-set to

41˚C as per TMV standards.

If the maximum

temperature is increased

the shower will no longer

comply with the TMV

scheme.

Turn ﬂow handle to

‘on’ position, letting

the temperature

stabilise.

8Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Isolation

Remove theRemove the

concealing capconcealing cap

from the shroud.from the shroud.

Rotate the shroudRotate the shroud

until the openinguntil the opening

aligns with thealigns with the

isolatisolatiion screw.on screw.

Turn the screwTurn the screw

to isolate theto isolate the

water. Reversewater. Reverse

the process whenthe process when

turning the waterturning the water

back on.back on.

Bristan products are made from premium materials, with hand polished, PVD, EPD or

electroplated ﬁnishes.

Your bar shower should be regularly cleaned with warm water, a mild pH-neutral liquid

soap, and polished with a soft cloth. Any residues from soap, toothpaste, shampoos and

shower gels can cause blemishes if not rinsed o straight after use.

Household bleaches and cleaners contain harsh chemicals and may damage the surface

ﬁnish. Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything

similar. Some surfaces such as nickel and pewter may be aected by the dye found in

some cloths, so it is also important to avoid hanging cloths on ﬁttings/barshowers etc.

Notes

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

General Cleaning

Tabla de contenidos

Otros manuales de Producto de plomería de Bristan

Bristan

Bristan W BASIN13 C Diagrama de cableado

Bristan

Bristan GLE385 W Instrucciones de montaje

Bristan

Bristan VAL2 BAS C CD (D2) Diagrama de cableado

Bristan

Bristan Quest Deck Sink Mixer Diagrama de cableado

Bristan

Bristan ZI SHXSMCT Diagrama de cableado

Bristan

Bristan Pivot Series Manual de usuario

Bristan

Bristan Buzz Diagrama de cableado

Bristan

Bristan W BATH12 C Diagrama de cableado

Bristan

Bristan CRZ SHXDIVCTFF C Diagrama de cableado

Bristan

Bristan SAF SHCDIV BLK (D1) Diagrama de cableado

Bristan

Bristan GLL FLEXSNK C (D1) Diagrama de cableado

Bristan

Bristan AR3 SHCDIV C Diagrama de cableado

Bristan

Bristan Jute JU BSM C Manual de usuario

Bristan

Bristan JAVA J BSM E8 C Manual de usuario

Bristan

Bristan Java Mini J MBAS C Manual de usuario

Bristan

Bristan Jute JU PBSM C Manual de usuario

Bristan

Bristan KN2 SHXAR C Instrucciones de montaje

Bristan

Bristan Quest Manual de usuario

Bristan

Bristan EV KIT-EFB C Instrucciones de montaje

Bristan

Bristan Options Bath Manual de usuario

Bristan

Bristan ALP Series Diagrama de cableado

Bristan

Bristan Java J SFSNK EF C Manual de usuario

Bristan

Bristan BL3105 Instrucciones de montaje

Bristan

Bristan Rio RO 1/2 C Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario