Bristan FLT BAS C Manual de usuario
Please keep this booklet for future
reference.
Installer, when you have read these
instructions please ensure you leave them
with the user.
Installation Instructions
Flute Tap Range
Models covered:
FLT BAS C, FLT 1HBF C,
FLT 2HBSM C, FLT TBAS C
www.divapor.com
2
Contents
Thank you for choosing Bristan, the UK’s leading taps and showers expert.
We have designed this product with your enjoyment in mind. To ensure that it works
to its full potential, it needs to be fitted correctly. These fitting instructions have been
created to give you all of the information you need and, if you need any further help,
please do not hesitate to contact us.
Important Safety Information................................................... 3
General Information ................................................................. 4
Specifications ........................................................................... 5
Dimensions............................................................................... 6-7
Installation Requirements ....................................................... 8
Installation................................................................................ 9-10
Maintenance ............................................................................. 11
Troubleshooting........................................................................ 12
Notes......................................................................................... 13
Guarantee ................................................................................. 14-15
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
www.divapor.com
3
Important Safety Information
•Please read these instructions thoroughly and retain for future use.
•All products manufactured and supplied by Bristan are safe provided they are
installed, used correctly and receive regular maintenance in accordance with these
instructions.
•If you are in any doubt about your ability to install this product safely you must
employ the services of an experienced qualified plumber.
•This fitting needs to be installed in accordance with, and meet the requirements of the
Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
•Remove all packaging and check the fitting for damage before starting installation.
•Warning: Before starting any installation please consider the following: before
drilling into walls, check that there are no hidden electrical wires, cables or water
supply pipes. This can be checked with the aid of an electronic detector.
•If power tools are used do not forget to: - Wear eye protection
- Unplug equipment after use
•Important: Remember to turn off the mains water supply before connecting to any
existing pipe work. Fitting isolating valves to the inlet feeds is recommended for ease
of maintenance.
•Warning: Before installing the new fitting it is essential that you thoroughly flush
through the pipework in order to remove any remaining swarf, solder, etc.
Failure to carry out this procedure could cause problems or damage to the workings of
the fitting.
•Take care when handling the ‘flexible connecting pipes’, do not bend, twist or crush
them. Only tighten the pipes by hand.
•Do not crush or kink the shower hose, this could damage the hose and cause leaks.
• This product must not be modified in any way as this will invalidate the guarantee.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
www.divapor.com
4
General Information
This product has been tested to the Water Regulations Advisory Scheme (WRAS) and
satisfies the requirements of the Water Supply (Water Fittings) Regulations 1999 and
current bylaws. For full Installation Requirements & Notes (IRN) please visit
www.wras.co.uk/directory.
Designed to comply with BS EN 200 for combination taps to be used within systems
designed to BS 6700.
BS 6700 recommends the temperature of stored water should never exceed 65°C.
A stored water temperature of 60°C is considered sufficient to meet all normal
requirements and will minimise the build up of lime scale in hard water areas.
If installing this product on a low pressure (tank fed) system please see specification
table (page 5) to determine the minimum distance required from underside of the cold
water tank to the outlet.
These taps and mixers should be installed in compliance with the Water Regulations.
Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the
mains, approved check valves must be fitted in the supply pipes.
For further details contact your Local Water Authority.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
www.divapor.com
5
Specifications
Product Code
Working pressure
Inlet
Minimum distance
from cold water tank
to outlet (metres)
Min Max
FLT BAS C 0.2 5.0 M10 15mm Compression Flexible Tails 2
FLT 1HBF C 0.5 5.0 M16 15mm Compression Flexible Tails 5
FLT 2HBSM C 1.0 5.0 M12 15mm Compression Flexible Tails 10
FLT TBAS C 0.2 5.0 M10 15mm Compression Flexible Tails 2
Maximum static pressure- 10.0 bar
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
www.divapor.com
6
Dimensions
Dimensions are nominal and in millimetres.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
Basin Mixer
Tall Basin Mixer
Basin Mixer
48
155
91
64
105
130
130
105
188
91
2
80
48
www.divapor.com
7
Dimensions Cont.
2 Hole Bath Shower Mixer
Dimensions are nominal and in millimetres.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
1 Hole Bath Filler
56
155
52
230
40
165
143
116
91
6
0
28
56
154
243
85
116
143
165
www.divapor.com
8
Installation Requirements
Flexible Connecting Pipes
Care must be taken when connecting the flexible connection pipes to the household pipework
to ensure they do not bend sharply and kink or twist.
See below for recommended ways to fit the flexible connecting pipes.
Slight
bend
90°
Angle
Kink Curved
round
Twists
Important: Failure to follow these guidelines may result in poor performance and damage
to the flexible connecting pipes.
Important: Full access must be made available on installation for future maintenance/
servicing purposes.
System Requirements:
Gravity fed hot & cold (Equal pressures)
Gravity fed hot & cold (Differential pressure, maximum ratio 5:1)
Unvented systems
Instantaneous water heater (Combination boiler)
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
www.divapor.com
9
Installation
1. Screw the flexi tails into the bottom
of the tap body by hand only
(DO NOT OVERTIGHTEN).
2. Feed the flexi tails through the hole,
ensuring the washer is fitted between the
body and the basin/ bath.
3. Screw the fixing rod into the bottom of
the tap. Slide 'C' shaped rubber washer
and 'C' shaped metal washer onto the
fixing rod up to the underside of the basin/
bath.
4. To secure the tap in place tighten the
fixing nut onto the fixing rod until is fully
tightened against the 'C' shaped metal
washer. Suitable spanner can be used to
fully tighten the fixing nut.
5. Connect the flexi tails to the hot and
cold water supplies.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
www.divapor.com
10
Installation Cont.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
6. Bath Shower Mixer only
Remove the nut, metal and rubber
washers from the handset holder
threaded tail.
Place the handset holder base through
the hole, slide the rubber and metal
washers onto the thread and secure in
place by tightening the backnut up to the
underside of the bath.
The screws on the backnut allow for any
uneven surfaces and should be tightened
up to the metal washer.
Feed the hose through the handset
holder base and connect the hose to the
shower outlet pipe using the small
sealing washer.
Fit the handset to the hose using the
small washer.
7. Basin Mixer and Tall Basin Mixer only
Fit the clicker waste ensuring the rubber
washer is fitted between the basin and
the waste. Place the other rubber washer
under the basin and secure in place by
tightening the backnut. In order to fill
the basin, the button in the middle of the
waste needs to be pressed down.
To release the water, press the button
again.
8. Turn on water supplies, lift the handle
upwards and operate in both directions,
letting the water flow for a few minutes.
9. Check all joints and connections for any
leaks.
www.divapor.com
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Accesorios de cocina y baño de Bristan
Bristan
Bristan Prism Manual de usuario
Bristan
Bristan TO DSM C Manual de usuario
Bristan
Bristan W BASIN04 C Manual de usuario
Bristan
Bristan CAS BAS C Manual de usuario
Bristan
Bristan Bright BRG BAS C Manual de usuario
Bristan
Bristan Z2 BIB C Diagrama de cableado
Bristan
Bristan Oval Tap Series Diagrama de cableado
Bristan
Bristan Liquorice LQR PROSNK C Diagrama de cableado
Bristan
Bristan Java Series Diagrama de cableado
Bristan
Bristan Nero NR BASNW C Diagrama de cableado
Bristan
Bristan Prism PM 3HWMBAS C Manual de usuario
Bristan
Bristan Z2 LUX 1/2 C Diagrama de cableado
Bristan
Bristan Acute AE 1/2 C Manual de usuario
Bristan
Bristan W SNK5C Diagrama de cableado
Bristan
Bristan GLL RAPSNK3 C Instrucciones de montaje
Bristan
Bristan 1901 Manual de usuario
Bristan
Bristan Gummers H64WMT Instrucciones de montaje
Bristan
Bristan Artisan Evo Instrucciones de montaje
Bristan
Bristan Z2 1/2 C Diagrama de cableado
Bristan
Bristan FH TDRD01 C Manual de usuario
Manuales populares de Accesorios de cocina y baño de otras marcas
Alpha Bidet
Alpha Bidet Alpha One Manual de usuario
InSinkErator
InSinkErator H/HC3300 Manual de instalación
Clou
Clou Xo type 1 Manual de usuario
Kohler
Kohler Contra 26448T-4 Manual de usuario
Grohe
Grohe Bridgeford 20 158 Manual de usuario
Hans Grohe
Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Manual de usuario