Brickcom Vandal Dome Series Hoja de datos

Easy Installation Guide

Megapixel Day & Night

Vandal Dome Network Camera

Vandal Dome Series

English

Step 1. Check Package Contents

a. Network Camera (Vandal Dome series)

b. Dry Bag, Strap Tie

c. Product CD

d. Location Sticker

e. Warranty Card

f. Screw Bag

g. Terminal Block

h. Allen Key

i. Easy Installation Guide

j. High Power PoE (Optional)

k. Wall-Mount Bracket: L-WM-01(Optional)

l. Waterproof Connector: WPC-EU (M20)/

WPC-US (3/4’’) (Optional)

Step 2. Hardware Installation

Do not mount the camera on any soft material. The camera may fall and be

damaged.

A compliant waterproof connector shall be attached tightly to the conduit hole

of the Vandal Dome Network Camera, and all the cables shall run through the

connector for the camera to be IP67-compliant.

This document is for the easy installation purpose only; please refer to the user

manual for more details.

I. Open The Vandal Dome Camera:

Use the Allen Key to unscrew the four screws and remove the dome cover from the camera device.

II. Open/Close The Conduit Hole:

The conduit hole allows the air to circulate through the camera device. By default, a lid is attached to

the conduit hole on the side of the camera device, and the conduit hole on the bottom of camera

device is open. Please use the screw driver to screw/ unscrew the lid. Please note that the lid and

the waterproof connector must be tightly screwed to the conduit hole to achieve IP67.

III. PoE, Power, DIDO, Audio Connection

Put all the cables, such as PoE , 12VDC power , DI / DO / Audio cable , together as one

single cable and run it through the waterproof connector. Then attach the waterproof connector to

the conduit hole or , and attach the lid tightly to the other hole. All cables are user-supplied.

Waterproof Connector

IV. For SD/SDHC Card Installation(Optional):

Insert the SD/SDHC card into the SD/SDHC card slot.

The SD/SDHC card is not included in the product package and needs to be purchased separately.

V. Dry Bag Installation:

Open the silver packing of the dry bag, then place the dry bag inside the camera device and secure

it using the strap tie.

VI. Mount The Camera To The Wall:

1) Choose the location on the wall to place the camera. Attach the location sticker to the desired

spot.

2) Drill four holes as instructed on the sticker.

3) Hammer the four plastic anchors which are provided in the product package into the four

location holes. Mount the camera on the wall and position the four screw holes over the plastic

anchors. Insert the screws into the holes and use the screwdriver to tighten the screws

clockwise into the holes until they are fixed.

VII. Mount The Camera to The Ceiling:

Mount the camera device on the desired location. Use the screwdriver to tighten the four included

screws clockwise through the four holes of the device as shown below. The best place to mount

the camera is the ceiling stud.

Step 3. Adjust The Lens (This function applies to all VD series, except the VD-***Nf and VD-***Af.)

I. Adjust The Lens Angle

1) The lens holder can be rotated clockwise or counter clockwise.

2) Release the tilt screw on both side of the device to tilt the lens up or down. After completion,

tighten the tilt screw.

3) Release the video adjustment screw to adjust the lens direction. After completion, tighten the

video adjustment screw.

II. Adjust The Viewing Angle and Focus

1) Release the zoom ring controller and then slide it left or right to get the desired field of view..

After completion, tighten the zoom ring controller.

2) Release the focus ring controller and slide it left or right to make the image in focus. After

completion, tighten the focus ring controller.

III. Complete The Installation

1) Place the dome cover on the camera device and slowly turn it until it is in the desired position.

2) Use the Allen Key to tighten the four dome screws to fix the dome cover onto the camera

device.

Please make sure the light sensor is not blocked by the dome cover.

Zoom Ring Controller

Focus Ring Controller

Step 4. Install Camera and Network Devices

I. Ethernet and DC12V Connection

Connect the camera to the Ethernet switch using an RJ45 Ethernet cable, and connect the DC12V

power adaptor to the camera device.

II. Power over Ethernet (PoE) Connection

1) Connect the camera to a PoE switch using a single Ethernet cable.

2) Connect the camera to a non-PoE switch using the PoE Injector.

Step 5.Install The EasyConfig Software

Insert the CD into the CD-ROM, and follow the instructions of the InstallShield Wizard to finish the

installation.

Step 6.Launch EasyConfig

Launch the EasyConfig software, and double click on the camera from the survey list to connect.

Step 7.Installation Completed

Click <Live View> to view the live video feed of the network camera.

Enter the default user name (admin) and password (admin) in the prompt request dialogue.

After connecting to the network Vandal Dome Camera, the request for installing the Brikcom ActiveX

control will appear below the URL bar. Right click on the bar, and click “Install Brickcom ActiveX

Control..”to permit ActiveX control installation.

In the pop-up security warning window, click “Install”to start downloading Viewer software on the

PC.

Otros manuales para Vandal Dome Series

Otros manuales de Cámara de seguridad de Brickcom

Brickcom

Brickcom MD-100Ae Manual de usuario

Brickcom

Brickcom Merge FD-300Ap Instrucciones de uso

Brickcom

Brickcom MD-500Ap Series Manual de usuario

Brickcom

Brickcom Fixed Box Series Manual de usuario

Brickcom

Brickcom FB-100A Series Manual de usuario

Brickcom

Brickcom Outdoor Bullet V2 Series Hoja de datos

Brickcom

Brickcom OB-100A Manual de usuario

Brickcom

Brickcom Fixed Dome Series Hoja de datos

Brickcom

Brickcom Vandal Dome Series Manual de usuario

Brickcom

Brickcom WFB-100A Manual de usuario

Brickcom

Brickcom VD-100A Instrucciones de uso

Brickcom

Brickcom OB-100A Manual de usuario

Brickcom

Brickcom OSD-040 36x Series Manual de usuario

Brickcom

Brickcom OB-502Ae V5 Series Instrucciones de uso

Brickcom

Brickcom OB-500Af V5 Series Hoja de datos

Brickcom

Brickcom CB-100A Series Manual de usuario

Brickcom

Brickcom VD-100A Manual de usuario

Brickcom

Brickcom Economy Outdoor Bullet Series Hoja de datos

Brickcom

Brickcom OB-100A V2 series Instrucciones de uso

Brickcom

Brickcom MB-500A Series Manual de usuario

Brickcom

Brickcom PZ-040 12x Series Manual de usuario

Brickcom

Brickcom Bullet Series Instrucciones de uso

Brickcom

Brickcom FB-100A Series Manual de usuario

Brickcom

Brickcom FB-130Np Series Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario