Box3d Box3d 500 Manual de instrucciones

Box3d building instructions

For box3d 500 and box3d XL

(version may 2018)

Box3d B.V.

Staalweg 1

2612KK Delft

Netherlands

[email protected]

www.box3d.eu

Safety instructions

Assembling your box3d requires some experience with technical tools and common sense. These

building instructions will guide you through the process of assembling your box3d 500 or box3d XL. We

have made this process as easily and accessible as possible. However, we cannot be responsible for any

harm during assembly or operation of box3d. Make sure you are confident at each step, or ask a more

experienced builder for help.

Box3d operates at 12V, so the user should never be involved with high voltage. However, current can

still be dangerous, so be careful at all times. Never plug in the power adapter into box3d during these

assembly.

Box3d includes a fan which regulates the temperature inside. Depending on the settings in the

controller, the fan can turn very fast with high power. So be careful not to touch the fan when box3d is

on.

We do not recommend to leave your printer and box3d running unattended.

3 
 
Contents 
Parts list.........................................................................................................................................................4 
Print your parts .............................................................................................................................................9 
Pre-assembly...............................................................................................................................................10 
Foam preparation .......................................................................................................................................12 
Top panel foam.......................................................................................................................................13 
Air inlet cutout........................................................................................................................................13 
Panel 1 (right panel)....................................................................................................................................14 
Panel 2 (left panel)......................................................................................................................................15 
Panel 3 (rear panel).....................................................................................................................................16 
Panel 4 (mid panel) .....................................................................................................................................17 
Panel 5 (front panel) ...................................................................................................................................18 
Connecting panels.......................................................................................................................................19 
Installing the door.......................................................................................................................................26 
Electronics...................................................................................................................................................30 
Paste top foam............................................................................................................................................36 
Paste sidewall foam ....................................................................................................................................37 
Close the top...............................................................................................................................................38 
 
 

Parts list

Parts

Qty 500

Qty XL

Inbus M4x10

Nut M4

Magnet + magnet ring

Inbus M4x16

Inbus M4x50

Washer M4

Washer M4 plastic

Metal screw M3x12

Washer M3

Nut M3

Hinge

Inbus wrench M4

Inbus wrench M5

Inbus M5x16

Inbus M5x20

Washer M5

Nut M5

Handle with 2 screws

Controller

Switch

Power connector

Sensor

USB cable

Power cable

(red/black)

Switch cable

Gland

O-ring

Tiewrap

Carbon filters

(optional)

Seperate

parts

Power adapter

Fan

Foam sheets

Window

Rubber seal

Front panel

Back panel

Left panel

Right panel

Bottom panel

Top outside panel

Top inside panel

Hepa filter

(optional)

Cutting template

Print your parts

-Go to box3d.eu to download the STL files for box3d.

-Print all files as shown in the table below. The “grouped” folder contains parts #1 - #6 in the

correct quantities, which might make it easier to print.

Qty

3D printing remarks

corner

No support needed

insert 2

No support needed

insert 3

No support needed

side connector

No support needed

magnet holder

No support needed

side connector high

No support needed

hinge spacer

No support needed

controller spacer

No support needed

fan outlet

Use support material

Optional

tube connector

120mm

No support needed

Optional

tube connector

100mm

No support needed

Optional

(filter

version)

filter housing + filter

clip

No support needed

Pre-assembly

-Fill every #1 with 3 M4 nuts, and lock them with #2. (12x #1, 12x #2, 36x nut M4)

-Fill every #4 with 2 M4 nuts, and lock them with #3. (15x #4, 15x #3, 30x nut M4)

-Insert 3 M4 nuts in #5, and lock them with #3. (1x #5, 2x #3, 3x nut M4)

-Insert the magnet in #5. A hard push is necessary to fully insert the magnet.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

Box3d box3d 500 Manual de instrucciones

Manuales populares de Impresora 3D de otras marcas