Bosch Security Systems SE2 Series Manual

SE2 Series

User Guide & Setup Instructions

Transmitters

Bosch Security Systems | 9/19 | 34453D

EN | 2

SE2 Series | User Guide & Setup Instructions | FCC Notice

FCC Notice

This device complies with Part 15 of the FCC Rules and

with RSS-210 of Industry and Science Canada.

Operation is subject to the following two conditions:

• This device may not cause harmful interference,

and

• This device must accept any interference received,

including interference that may cause undesired

operation.

FCC ID: ESV-0117-1

Canada: 1249 102 643

EN | 3

SE2 Series | User Guide & Setup Instructions |

Bosch Security Systems | 9/19 | 34453D

1.0 Part I - User Guide

1.2 Using the SE2 Transmitter

This feature is enabled on this transmitter.

This feature is not enabled on this transmitter.

1.2.1 Standard Operation

Transmitting a Manual Alarm

To send an alarm, press and hold the Alarm button for 1

second. The transmitter sends an alarm signal to the

central console. With some SE2 models, you can also

visually confirm the signal if done in sight of a receiver

(receiver lights the red LED). After a manual alarm is

initiated, the auto tracking feature begins. The

transmitter sends a signal to the central console every 7

sec., updating your location. Toreset the transmitter after

a manual alarm is initiated, perform a test as described

in Testing the Transmitter.

Testing the Transmitter

Totest your transmitter, stand in sight of a siren/strobe

or a receiver. While holding down the Test button, press

the Alarm button until you hear an audible tone. A test

transmission is sent to the central console. Also, the

strobe on an outdoor siren/strobe or the green LED on a

receiver illuminates.

There might be a brief delay of 2 sec. to

3 sec. before the flashing light appears.

If you do not receive confirmation of a successful test

transmission (such as the strobe on a siren/strobe or the

green LED on a receiver not illuminating), try the test

again. If there is still no confirmation, take the

transmitter to the security department.

1.0 Part I - User Guide

(For Distribution to All SE Users)

1.1 Introduction

The SE2 Series Transmitters are personal transmitters

designed to work with the Security Escort system. When

initiated, a signal identifying you and your location is

sent to the Security Escort monitoring station. The SE2

can also be tested within sight of a receiver or siren/

strobe by the user.

There are several SE2 models available, each

with optional features. Check boxes are

provided in this document for your security

department to indicate which features are

available on your transmitter.

The Security Escort system is not a

substitute for safe behavior. System users

should not take personal risks under the

misconception that the system provides

protection that compensates for taking such

risks.

Figure 1: SE Transmitter

1 - Test button

2 - Alarm button

3 - Lanyard

Bosch Security Systems | 9/19 | 34453D

EN | 4

SE2 Series | User Guide & Setup Instructions | 1.0 Part I - User Guide

Figure 2: Belt Clip Attachment

1 - Must use

2 - Optional

3 - Side view of clip

4 - Clip

5 - Back of transmitter

1.2.2 Optional Features

Man-Down Alarm Feature

With the man-down feature enabled, the transmitter

alarms whenever the transmitter (you) is in a prone

position (60° from upright). The transmitter emits an

audible tone upon sensing the prone position, and

initiates the auto tracking feature. To reset the

transmitter after a man-down alarm is initiated, return

the transmitter to the upright position and perform a test

as described in Section 1.2.1 Standard Operation.

Lanyard Snatch Alarm Feature

With the lanyard snatch alarm feature enabled, the

transmitter sends an alarm signal to the central console

and initiates the auto tracking feature when the lanyard

pin is pulled out of the unit. To reset the transmitter

after a lanyard snatch alarm is initiated, reinsert the

lanyard pin and perform a test as described in Section

1.2.1 Standard Operation.

1.2.3 Wearing the Transmitter

The transmitter comes with a clip which can be worn

over a pocket or belt, or be secured to a belt. Secure the

clip to the transmitter (screws provided) at the two top

positions to use it as a clip.

To use the clip securely on a belt, attach it at the third

location at the bottom. Use the screw already securing

the battery door.

The clip is designed to wear on a security type utility

belt. If worn on a thin belt, be aware that such a loose

fitting can cause the transmitter to activate the

man-down alarm (if enabled) when there is too much

loose movement.

EN | 5

SE2 Series | User Guide & Setup Instructions |

Bosch Security Systems | 9/19 | 34453D

2.0 Part II - Setup Instructions

(For Security Department Use Only)

2.1 Models and Features

The various SE2 models and their features are identified

in Table 2.

Table 1: SE2 Models and Features

Model

Feature SE2S SE2U SE2M* SE2S-SN SE2U-SN

Man-Down     

Supervision

Tracking

    

Lanyard

Snatch

  

Auto

Tracking

   

Silent

Manual

Alarm

 

Low Battery

Indication

    

* SE2M is only used for system testing and does not generate a system

alarm.

Figure 3: Back of Transmitter

1 - Retaining screw

2 - Pry here

2.2 Removing the Cover

The Man-Down, Supervision Tracking, and Lanyard

Snatch features are controlled by the jumpers located

next to the battery compartment.

To remove the cover:

1. Remove the belt clip (if used).

2. Remove the retaining screw on the back of the

enclosure (see Figure 3).

3. Using a flat-head screwdriver, pry the lower part of

the front cover away from the rest of the enclosure.

Before distributing the attached User Guide,

place an “X” in the box next to each feature

enabled on the transmitter.

Bosch Security Systems | 9/19 | 34453D

EN | 6

SE2 Series | User Guide & Setup Instructions | 2.0 Part II - Setup Instructions

Figure 5: Jumper Positions

1 - Off

2 - On

Remove the battery before moving the

jumpers.

2.3 Enabling/Disabling Features

Figure 4 shows the location of the specific jumper for

each feature. Note that the lanyard-snatch jumper and

lanyard switch are only included on the SE2M,

SE2S-SN, and SE2U-SN models.

Figure 4: Internal Components

1 - Lanyard switch

2 - Man-down jumper

3 - Supervision jumper

4 - Lanyard jumper

5 - Battery compartment

-5

2.3.1 Supervision Feature

To enable the supervision tracking feature, place its

jumper in the ON position, as indicated in Figure 5. Do

this by moving the jumper to cover both pins using a

small pair of pliers. With supervision tracking enabled,

the transmitter sends a silent transmission to the central

console approximately every 90 seconds. This enables

the central console to monitor the battery and

transmitter condition, as well as track the transmitter’s

location within the protected area.

2.3.2 Man-Down and Lanyard Snatch Features

To enable the man-down and lanyard snatch features,

place the desired feature jumper in the ON position as

shown in Figure 5. Use a small pair of pliers to move the

jumper so it covers both pins.

See Section 1.2.2 Optional Features for descriptions of

these features.

2.3.3 Battery

The transmitter uses a CR2, 3 V lithium battery. The

central console indicates when the battery is low and

needs replacement.

See Figure 4 for battery polarity. The battery life

depends on usage and enabled features.

EN | 7

SE2 Series | User Guide & Setup Instructions |

Bosch Security Systems | 9/19 | 34453D

2.0 Part II - Setup Instructions

Notes:

Bosch Security Systems

130 Perinton Parkway

Fairport, NY 14450-9199 USA

www.boschsecurity.us

Customer Service: (800) 289-0096

Technical Support: (888) 886-6189

Subject to change | Printed in the USA

34453D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Bosch

Bosch

Bosch CRS-MIYS37-FI Manual de usuario

Bosch

Bosch CRS-SB-424FI Manual de usuario

Bosch

Bosch ATX-TRM-304T01 Manual de usuario

Bosch

Bosch CRS-NC-S37E-ACC Manual de usuario

Bosch

Bosch SE3401 Manual de usuario

Bosch

Bosch MIYN46 Manual de usuario

Bosch

Bosch ISW-EN1261HT Manual de usuario

Bosch

Bosch SE-TRM-433T01 Manual de usuario

Bosch

Bosch ISW-EN1233 Manual de usuario

Bosch

Bosch CRS-NC-S37L-US Manual de usuario

Bosch

Bosch INTEGRUS Manual de usuario

Bosch

Bosch ISW-EN1235DF Manual de usuario

Bosch

Bosch RADION RFUN-A Manual de usuario

Bosch

Bosch SE88 Manual de usuario

Bosch

Bosch EN1210 Series Manual de usuario

Bosch

Bosch ISW-EN1210SK Manual de usuario

Bosch

Bosch CRS-SB-423FI Manual de usuario

Bosch

Bosch ATX-TRM-304T01 Manual de usuario

Bosch

Bosch SEC-RFPB60M-433 Manual de usuario

Bosch

Bosch S35 Manual de usuario

Bosch

Bosch SE88A-90S-304 Manual de usuario

Bosch

Bosch ISN-GMX-S1 Manual de usuario

Bosch

Bosch ISW-EN1215EOL Manual de usuario

Bosch

Bosch NurseCall N46 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario