Bosch VEZ Series Manual de usuario

AutoDome Easy II

VEZ Series

en Installation Manual

AutoDome Easy II Table of Contents | en 3

Bosch Security Systems, Inc. Installation Manual F.01U.164.478 | 2.0 | 2010.02

Table of Contents

1Safety 7

1.1 Important Safety Instructions 7

1.2 Safety Precautions 10

1.3 Important Notices 10

1.4 Customer Support and Service 17

2 Unpacking 18

2.1 Parts List 18

2.2 Safety Rules 19

3 Description 20

4 Installing a Surface Mount 21

4.1 Description 21

4.1.1 Additional Tools Required 22

4.1.2 Preparing the Surface Mount for an Indoor Installation 22

4.1.3 Preparing the Surface Mount for an Outdoor Installation 24

4.1.4 Installing the Camera to the Mounting Plate 28

5 Installing a Wall Mount 31

5.1 Description 31

5.1.1 Additional Tools Required 32

5.1.2 Preparing the Wall Mount for an Indoor Installation 32

5.1.3 Preparing the Wall Mount for an Outdoor Installation 34

5.1.4 Installing the Camera to the Mounting Plate 38

6 Installing a Recessed Mount 42

6.1 Description 42

6.1.1 Additional Requirements 42

6.1.2 Preparing the Ceiling for Installation 43

6.1.3 Installing the Camera to the Mounting Plate 46

4en | Table of Contents AutoDome Easy II

F.01U.164.478 | 2.0 | 2010.02 Installation Manual Bosch Security Systems, Inc.

7 Installing a Pipe Mount 50

7.1 Description 50

7.1.1 Tools/Supplies Required 51

7.1.2 Preparing the Ceiling for Installation 51

7.1.3 Installing the Camera to the Mounting Plate 58

8 Preparing the Wiring 61

8.1 Power 61

8.2 Connecting the Power 62

8.2.1 Power Connections to Indoor Cameras 62

8.2.2 Power Connections to Outdoor Cameras 63

8.2.3 Power Connections to Heater (all outdoor models) 64

8.3 Video and Bilinx Cables 65

8.4 Connecting the Video 66

8.5 Control-only Cables 66

8.5.1 Biphase 66

8.5.2 Direct Control 67

8.5.3 Daisy Chaining 68

8.5.4 RS485 69

9 Alarms and Relay Connections 71

9.1 Alarm Input 71

9.2 Connecting Alarms (inputs 1 through 2) 72

9.2.1 Connecting a Normally Open Alarm 72

9.2.2 Connecting a Normally Closed Alarm 73

9.3 Alarm Outputs 74

9.3.1 Connecting an Open Collector Output 74

10 Getting Started 75

10.1 Powering On 75

10.2 Establishing AutoDome Easy II Control 75

10.2.1 Basic Keyboard Operation 76

10.2.2 Keyboard Commands 77

10.3 Setting the Camera Address 77

10.3.1 FastAddress 78

AutoDome Easy II Table of Contents | en 5

Bosch Security Systems, Inc. Installation Manual F.01U.164.478 | 2.0 | 2010.02

11 On-Screen Display Menu Navigation 80

11.1 Setup Menu 80

11.2 Camera Setup Menu 82

11.3 Lens Setup 85

11.4 PTZ Setup Menu 87

11.5 Display Setup Menu 90

11.5.1 Specifying a Shot or a Sector Title 93

11.6 Communication Setup Menu 94

11.7 Alarm I/O Setup 96

11.8 Alarm I/O Rule Setup Menu 99

11.9 Language Menu 102

11.10 Diagnostics Menu 103

12 Common User Commands (unlocked) 106

12.1 Setting AutoPan Mode 106

12.2 Setting Preset Shots 106

12.3 Configuring Preposition Tours 107

12.4 Programming the Inactivity Operation 108

12.5 Recorded Tours 108

13 Pelco On-Screen Menus 109

13.1 Setup Menu 109

13.1.1 Command Lock (locked) 111

13.1.2 Bosch Menu (locked) 111

13.1.3 PTZ Setup (unlocked) 113

13.1.4 Other Menus 114

14 Keyboard Commands by Number 115

15 Preventive Maintenance 120

16 Troubleshooting 121

16.1 AutoDome Easy II Operation and Control 122

6en | Table of Contents AutoDome Easy II

F.01U.164.478 | 2.0 | 2010.02 Installation Manual Bosch Security Systems, Inc.

A Alternative Control Protocols 126

A.1 Setting FastAddress with Alternative Protocols 126

A.1.1 Using a Pelco Controller 126

A.2 Pelco Protocol Mode 127

A.2.1 Hardware Configuration 128

A.2.2 Pelco Keyboard Commands 128

A.2.3 Pelco Keyboard Commands 129

A.2.4 Special Preset Commands 130

Index 131

AutoDome Easy II Safety | en 7

Bosch Security Systems, Inc. Installation Manual F.01U.164.478 | 2.0 | 2010.02

1Safety

1.1 Important Safety Instructions

Read, follow, and retain for future reference all of the following

safety instructions. Heed all warnings on the unit and in the

operating instructions before operating the unit.

1. Cleaning - Unplug the unit from the outlet before cleaning.

Follow any instructions provided with the unit. It is

generally sufficient to use a dry cloth for cleaning, but a

moist lint-free cloth or leather shammy may also be used.

Do not use liquid cleaners or aerosol cleaners.

2. Heat sources - Do not install the unit near any heat

sources such as radiators, heaters, stoves, or other devices

(including amplifiers) that produce heat.

3. Ventilation - Any openings in the unit housing are provided

for ventilation to prevent overheating and ensure reliable

operation. Do not block or cover these openings. Do not

place the unit in an enclosure unless proper ventilation is

provided, or the manufacturer's instructions have been

adhered to.

4. Water - Do not use this unit near water, for example near a

bathtub, washbowl, sink, laundry basket, in a damp or wet

basement, near a swimming pool, or in any area classified

as a wet location. To reduce the risk of fire or electrical

shock, do not expose this unit to rain or moisture.

5. Object and liquid entry - Never push objects of any kind

into this unit through openings, as they may touch

dangerous voltage points or short out parts, which could

result in a fire or electrical shock. Never spill liquid of any

kind on the unit. Do not place objects filled with liquids,

such as vases or cups, on the unit.

6. Lightning - For added protection during a lightning storm,

or when leaving this unit unattended and unused for long

periods, unplug the unit from the wall outlet and

disconnect the cable system. This will prevent damage to

the unit from lightning and power line surges.

8en | Safety AutoDome Easy II

F.01U.164.478 | 2.0 | 2010.02 Installation Manual Bosch Security Systems, Inc.

7. Control adjustment - Adjust only those controls specified

in the operating instructions. Improper adjustment of

other controls may cause damage to the unit. Use of

controls or adjustments, or performance of procedures

other than those specified, may result in hazardous

radiation exposure.

8. Overloading - Do not overload outlets and extension cords.

This can cause fire or electrical shock.

9. Power disconnect - Units with or without ON/OFF

switches have power supplied whenever the power cord is

inserted into the power source; however, the unit is

operational only when the ON/OFF switch is in the ON

position. The power cord is the main power disconnect

device for switching off the voltage for all units.

10. Power sources - Operate the unit only via the type of

power source indicated on the label. Before proceeding,

be sure to disconnect the power from the cable being

connected to the unit.

– For battery powered units, refer to the operating

instructions.

– For units supplied by an external power source, use

only the recommended or approved power supplies.

– For limited power source units, this power source

must comply with EN60950. Substitutions may

damage the unit or cause fire or shock.

– For 24 VAC units, voltage applied to the unit's power

input should not exceed +/- 10% or 21.6-26.4 VAC.

User-supplied wiring must comply with local electrical

codes (Class 2 power levels). Do not ground the

supply at the terminals or at the unit's power supply

terminals.

– If unsure of the type of power supply to use, contact

your dealer or local power company.

11. Servicing - Do not attempt to service this unit yourself.

Opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

AutoDome Easy II Safety | en 9

Bosch Security Systems, Inc. Installation Manual F.01U.164.478 | 2.0 | 2010.02

12. Damage requiring service - Unplug the unit from the main

AC power source and refer servicing to qualified service

personnel when any damage to the equipment has

occurred, for example if:

– the power supply cord or plug is damaged

– exposure to moisture, water, and/or inclement

weather (rain, snow etc.)

– liquid has been spilled in or on the equipment

– an object has fallen into the unit

– the unit has been dropped or the unit cabinet is

damaged

– the unit exhibits a distinct change in performance

– the unit does not operate normally when the user

correctly follows the operating instructions.

13. Replacement parts - Be sure the service technician uses

replacement parts specified by the manufacturer, or that

they have the same characteristics as the original parts.

Unauthorized substitutions may cause fire, electrical

shock, or other hazards.

14. Safety check - Safety checks should be performed on

completion of service or repairs to the unit, to ensure that

the unit is in proper operating condition.

15. Installation - Install in accordance with the manufacturer's

instructions and in accordance with applicable local codes.

16. Attachments, changes, or modifications - Only use

attachments/accessories specified by the manufacturer.

Any change to or modification of the equipment not

expressly approved by Bosch could void the warranty or, in

the case of an authorization agreement, authority to

operate the equipment.

10 en | Safety AutoDome Easy II

F.01U.164.478 | 2.0 | 2010.02 Installation Manual Bosch Security Systems, Inc.

1.2 Safety Precautions

1.3 Important Notices

Accessories - Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall, causing serious

injury to persons and/or severe damage to the unit. Use only

with the cart, stand, tripod, bracket, or table specified by the

manufacturer. When a cart is used, exercise caution and care

when moving the cart/apparatus combination to avoid tipping it

over, which could result in injury. Quick stops, excessive force,

or uneven surfaces may cause the cart/unit combination to

overturn. Mount the unit in line with the manufacturer's

instructions.

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building. If it is needed to open the

housing for servicing and/or other activities, use this all-pole

DANGER!

This symbol indicates an imminently hazardous situation such

as “Dangerous Voltage” inside the product. If not avoided, this

will result in an electrical shock, serious bodily injury, or death.

WARNING!

Indicates a potentially hazardous situation. If not avoided, this

may result in minor or moderate injury. Alerts the user to

important instructions accompanying the unit.

CAUTION!

Indicates a potentially hazardous situation. If not avoided, this

may result in damage to property or risk of damage to the unit.

NOTICE!

This symbol indicates information or a company policy that

relates directly or indirectly to the safety of personnel or

protection of property.

Otros manuales para VEZ Series

Tabla de contenidos

Otros manuales de Cámara de seguridad de Bosch

Bosch

Bosch EXTEGRA IP 9000 FX Manual de usuario

Bosch

Bosch use IP FLEXIDOME IP starlight 6000 VR Manual de usuario

Bosch

Bosch VDN-498V03-21 Manual de usuario

Bosch

Bosch NUC-52051-F0 Manual de usuario

Bosch

Bosch AN bullet 2000 IR Manual de usuario

Bosch

Bosch LTC0485/11 Manual de usuario

Bosch

Bosch VDC-250 Manual de usuario

Bosch

Bosch AUTODOME 7000 VG5-7230 Manual de usuario

Bosch

Bosch VEI-Series Manual de usuario

Bosch

Bosch NBN-80052 Manual de usuario

Bosch

Bosch NTI-40012-A3 Manual de usuario

Bosch

Bosch FlexiDomeXT LTC 1361/10 Manual de usuario

Bosch

Bosch AUTODOME 4000 Manual de usuario

Bosch

Bosch VG4 Series Manual de usuario

Bosch

Bosch LTC 0465 Series Manual de usuario

Bosch

Bosch MIC IP starlight 7000i Manual de usuario

Bosch

Bosch AUTODOME 700 Series Manual de usuario

Bosch

Bosch MIC Series 550 Manual de usuario

Bosch

Bosch EX49 Manual de usuario

Bosch

Bosch NBN-80052 Manual de usuario

Bosch

Bosch LTC 0455 Series Manual

Bosch

Bosch VG4-322-ECS0WF Manual de usuario

Bosch

Bosch Dinion2X NBN-498 Manual de usuario

Bosch

Bosch DINION IP starlight 6000 HD Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario