Bosch Rexroth CKL Series Guía
Commissioning the CKL Drive
Controller
USL00010
01.2015
Bosch Rexroth Corp., USL00010, 01.2015
The data specied only serve to describe the
product. No statements concerning a certain
condition or suitability for a certain application
can be derived from our information. Catalog
specications do not constitute assured
characteristics. The information given does
not release the user from the obligation of
own judgment and verication. It must be
remembered that our products are subject to a
natural process of wear and aging.
© This document, as well as the data,
specications and other information set forth in
it, are the exclusive property of Bosch Rexroth
Corp. It may not be reproduced or given to
third parties without its consent.
Original instruction manual.
2
01.2015, USL00010, Bosch Rexroth Corp.
Contents
1 General 4
2 Commissioning 4
3 Commissioning Flowcharts 5
4 Preconditions 8
5 Network Connection 9
6 Firmware 11
7 Language Selection 14
8 Master Communication 15
9 Power Supply 16
10 Scaling/Mechanical System 17
11 Limit Values 19
12 Motor 21
13 Motor Encoder 26
14 Data Reference Motor Encoder 27
15 Axis Control Parameters 28
16 Commutation Settings 29
17 Easy Startup Mode 30
18 Drive Error Diagnostics 31
19 DetermineCommutationOset 33
20 Enable Drive Power 34
21 VerifyCommutationOset 35
22 Home Axis 36
23 Stop Initial Commissioning Mode 37
24 Save/Backup Parameters 38
25 Move Axis 39
26 Optimize Control Loops 40
3Contents
Bosch Rexroth Corp., USL00010, 01.2015
1 General
1.1 Scope and purpose of the documentation
• This document is intended to be a guideline for initial axis commissioning of the CKL Linear
Motor Module.
• The parameters found within are based solely on the use of Bosch Rexroth IndraDrive Cs
servo drives.
• For 3rd Party Servo Drives, while items on the initial parameter set may be the same, expect
minor adjustment requirements depending on the Drives‘ Manufacturer recommendations.
2 Commissioning
• Verify actual CKL system in-hand and all Preconditions (see page 5).
• Print or display the “Commissioning Flowchart” Part 1 and Part 2 relevant to Hall sensor
type as you commission the CKL system.
• Step through the owchart by reading the relevant instruction pages.
• Please be advised, the instruction pages are NOT meant to be completely read straight-
through in page order. For example, if using analog Hall sensor, not all instruction pages are
necessary (see owchart). Furthermore, depending on success/failure of a step, looping
through previous steps might be required (see owchart).
4General Information
01.2015, USL00010, Bosch Rexroth Corp.
3 Commissioning Flowcharts
3.1 Commissioning Flowchart – Part 1
Digitalornone
Analog
StartInitialCommissioning
NetworkConnection
Firmware
LanguageSelection
MasterCommunication
PowerSupply
Scaling/MechanicalSystem
LimitValues
DataReferenceMotorEncoder
Preconditions
Motor
MotorEncoder
HallSensor?
AnalogHall
DigitalHallorwithoutHall
AxisControlParameters
Proceed to Part 2 for relevent Hall Sensor type.
5Commissioning Flowcharts
Bosch Rexroth Corp., USL00010, 01.2015
3.2 Commissioning Flowchart – Part 2 – Analog Hall
AnalogHall
Yes
No
EasyStartupMode
PMtoOM?
DriveErrorDiagnostics
HomeAxis
FinishedInitialCommissioning
EnableDrivePower
Yes,with
Basic
Parameters
Yes,withOptimizedParameters
No
SaveBasicParameters
OptimizeControlLoops
MoveAxis
MotionOK?
SaveOptimizedParameters
6Commissioning Flowcharts
01.2015, USL00010, Bosch Rexroth Corp.
3.3 Commissioning Flowchart – Part 2 – Digital Hall or without Hall
No
Yes
DigitalHallorwithoutHall
No
Yes
No
CommutationSettings
EasyStartupMode
PMtoOM?
DriveErrorDiagnostics
DetermineCommutationOffset
Successful?
VerifyCommutationOffset
StopInitialCommissioningMode
SaveBasicParameters
DisableDrivePower
FinishedInitialCommissioning
EnableDrivePower
OptimizeControlLoops
ManuallyRepositionAxistoAllow
UnrestrictedMovement
MoveAxis
MotionOK?
SaveOptimizedParameters
HomeAxis
Yes,with
Basic
Parameters
Yes,withOptimizedParameters
NotOK
OK
P519Bit1=1,commutationoffsetoptimizedtoref(homed)point
P519Bit1=0,commutationoffsetnotoptimized
7Commissioning Flowcharts
Bosch Rexroth Corp., USL00010, 01.2015
4 Preconditions
4.1 Commissioning the CKL drive controller
4.1.1 Hardware
Compact Module CKL
System size Carriage length Primary part Secondary part
CKL 110 180 mm MCP030B-V180-NI-xxCN-NNNN MCS030-3S-xxxx-NNNN
240 mm MCP030C-V180-NI-xxCN-NNNN MCS030-3S-xxxx-NNNN
300 mm MCP030D-V180-NI-xxCN-NNNN MCS030-3S-xxxx-NNNN
CKL 145 244 mm MCP040C-V300-NI-xxCN-NNNN MCS040-3S-xxxx-NNNN
364 mm MCP040E-V300-NI-xxCN-NNNN MCS040-3S-xxxx-NNNN
484 mm MCP040G-V300-NI-xxCN-NNNN MCS040-3S-xxxx-NNNN
CKL 200 237 mm MCP070C-V300-NI-xxCN-NNNN MCS070-3S-xxxx-NNNN
297 mm MCP070D-V300-NI-xxCN-NNNN MCS070-3S-xxxx-NNNN
417 mm MCP070F-V300-NI-xxCN-NNNN MCS070-3S-xxxx-NNNN
xx: L0 = digital Hall, L1 = analog Hall, N0 = without Hall
xxxx: 0120, 0180, 0300 = secondary part length mm, select any value
HCS01 IndraDrive Cs with Firmware MPx-17V08 or greater
Supported feedback combinations:
Firmware Encoder HCS01
connector
Hall unit HCS01
connector
Additional hardware requirement
MPE/B/C analog X4 without without none
MPE/B/C digital X4 without without none
MPE/B/C analog X4 digital X4 with SHL03 Hall sensor box
MPB/C digital X4 analog X8 with HCS01 dual encoder interface (EC-EC)
MPB/C analog X4 analog X8 with HCS01 dual encoder interface (EC-EC)
Firmware: MPE=Economy, MPB=Basic, MPC=Advanced
Encoder: digital encoder is supported but analog encoder is recommended with IndraDrive!
For detailed descriptions of rmware and encoders, please see the IndraDrive MPx-17 (or later) Functions
Applications Manual.
4.1.2 Software
• IndraWorks Ds 13VRS (recommended)
• IndraWorks Ds 12VRS (possible with caution*)
4.1.3 Operating System
• Windows 7 (recommended)
• Windows XP (possible with caution*)
NOTE: Caution* = software bugs, unexpected behavior, limited tests
8Preconditions
01.2015, USL00010, Bosch Rexroth Corp.
5 Network Connection
5.1 Connect PC to IndraDrive via the Non-Real Time (NRT) channel for
drive commissioning
5.1.1 Stepsforconguringthenetworkconnection:
1. Right mouse button click on Local Area Connection and select Properties in the pop-up
menu.
2. Select Internet Protocol (Windows XP) or Internet Protocol Version 4 (Windows 7).
3. Press the Properties button.
9Network Connection
Bosch Rexroth Corp., USL00010, 01.2015
5.1.1 Stepsforconguringthenetworkconnection(continued)
4. Enter a unique IP address for the PC (must be dierent than the IndraDrive, see
below note), then click inside the Subnet mask eld, the Subnet mask will default to
255.255.255.0.
5. Open IndraWorks Ds.
6. Enter the IP address of the IndraDrive, the default factory setting is 192.168.0.1.
7. Press the Browse button.
8. The connected IndraDrive appears with device information.
9. Press the OK button.
NOTE: If the IP address of the IndraDrive is 192.168.0.1, then the PC’s rst three dot-decimal
numbers must be the same (for example, 192.168.0.x). The fourth number (x) must be
dierent from that of the IndraDrive’s IP address, and be a number between 0 to 255.
10 Network Connection
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Controladores de Bosch
Bosch
Bosch Smart Home controller II Manual del operador
Bosch
Bosch Plena LBB1990/00 Instrucciones de montaje
Bosch
Bosch Smart Home Controller AA Manual de usuario
Bosch
Bosch Worcester Digital Twin Channel Programmer Manual
Bosch
Bosch AMC-4W Manual de usuario
Bosch
Bosch REXROTH SB356 Manual de usuario
Bosch
Bosch Rexroth EcoDrive 03 Manual de usuario
Bosch
Bosch 560 DDC Manual de usuario
Bosch
Bosch LSU4 Manual de usuario
Bosch
Bosch Rexroth Diax 04 Manual de usuario
Bosch
Bosch Rexroth ctrlX CORE X7 Manual de usuario
Bosch
Bosch Rexroth VT-HNC100 3X/S Series Manual de instrucciones
Bosch
Bosch HPC Manual de usuario
Bosch
Bosch CRC200 Manual de usuario
Bosch
Bosch rexroth CHC Manual de usuario
Bosch
Bosch Lambdatronic LT4 ADV Manual de instrucciones
Bosch
Bosch MPC 2000 A Manual de usuario
Bosch
Bosch CS 550 Manual de usuario
Bosch
Bosch rexroth HMS01 Manual de usuario
Bosch
Bosch FHP560 Instrucciones de uso
