Bosch Eplus ACTIVE LINE Manual de usuario

INSTALLATION

BOSCH

ENGINES

[email protected] // www.eplus.bike

Via Pontestura 124 Camino 15020 (AL) Italy

eplus

ACTIVE LINE

PERFOMACE LINE

PERFOMACE LINE CX

3.07 VERSION

2. INSTALLATION

INSTALLATION

Connection

ATTENTION

It is forbidden by law to activate EPLUS speed unlocker in public places such as streets,

squares and cycling paths. So it is only possible to activate EPLUS speed unlocker in private

places such as circuits and private properties.

The manufacter denies responsibility due to any damage to pedal assisted bicycles

where Eplus is set up. The manufacter denies responsibility due to any harm to people or

objects.

Unplug the connectors

Looking at the bike from behind, on the left side (opposite side to the chainring),

remove the 3 Torx screws (T20) that hold the protective cap of the Bosch engine

(in this case Performance CX).

Remove the battery from e-bike

3. INSTALLATION

After removing the protective cover, identify the two plugs of the display (the second

connector from left of 4 wires colored: yellow-green-black-red) and the speed sensor

(2 wire plug fully right: black-red).

With a long forceps carefully remove the two plugs paying attention not to pinch

them ruining plugs or wires.

4. INSTALLATION

Insert the thermoshrinking sheath (enclosed) in the two disconnected wires,

pushing it over the plug.

Insert plugs (output cables from the chip) in their respective two sockets

(cables disconnected from the engine) respecting the correct wire color: DISPLAY PLUG >

YELLOW-YELLOW / GREEN-GREEN / BLACK-BLACK / RED-RED

AND SPEED SENSOR PLUG > BLACK-BLACK / WHITE-RED

USE EXTREME ATTENTION TO CORRECTLY ASSEMBLE THE COLORS! CAUTION: WRONG

CONNECTION LEADS TO SHORTCIRCUIT, DAMAGES NOT COVERED BY WARRANTY!

5. INSTALLATION

SPEED SENSOR

SOCKET

SPEED SENSOR

PLUG

HMI (DISPLAY)

PLUG

HMI (DISPLAY)

SOCKET

TO THE DISPLAY

(HMI) PLUG:

RED => RED

BLACK => BLACK

GREEN => GREEN

YELLOW => YELLOW

(SEE PHOTO 5)

TO THE SPEED

SENSOR PLUG:

BLACK => BLACK

RED => WHITE

(SEE PHOTO 5)

6. INSTALLATION

Carefully cover the two plugs with shrink wrap and with a hair dryer or a lighter heat uniformly the

sheath (turning it from right to left) until you have the sheath that takes the shape of the plugs.

Be careful not to burn wires or plugs.

7. INSTALLATION

Now connect the two plugs remaining on the chip to the engine, respecting the correct posi-

tion of the colors (display RED WIRE and speed sensor WHITE WIRE get to the RIGHT) and push

the connectors rmly to the end; CAUTION: WRONG CONNECTION LEADS TO SHORTCIRCUIT,

DAMAGES NOT COVERED BY WARRANTY!

WHITE WIRE TO RIGHT

RED WIRE TO RIGHT

Possibly arrange the cables with electrician clamps paying attention that there are no wires in

correspondence with holes where cover’s screws are and close it gently.

8. INSTALLATION

The engine unlock at 25 km / h is activated by pressing the Walk button on the

on-board computer. The activation button can be changed (see pag. 9).

The display will show the value 2.2 if the unlock has been activated and 1.1 if it is

deactivated.

Racing Speed Unlocker/Advanced is compatible with Purion, Nyon and Intuvia

displays.

If you have Intuvia or Nyon displays, for correct operation follow the instructions

on page. 9/10.

RACING MODE

AC TIVATION OF

THE SPEED UNLOCK

DATA VIEW ON THE DISPLAY

Purion: correct speed, correct km done

Intuvia: correct speed, correct km done, total km 00

Nyon: correct speed, km done with unlock activated halved

9. INSTALLATION

MENU O.5 - For changes to the factory settings

The SPEED UNLOCKER chip, factory mode, is set to be switched on / o using the WALK button

and calibrated for 27.5 “wheels (2170 mm in circumference) and to be used with Purion/Nyon

Display.

To change the default parameters follow the next procedure scrupulously:

1. Turn on the display and place the aid level in OFF mode

2. Press the [-] button on the handlebar 4/5 times until the number 0.5 appears on the display

3. 3. Move the [+ -] keys on the handlebar and enter the menu to be modied choosing between

1,2,3,4,5,6 (large number on display).

parameter [0.5] > For INTUVIAvisualization of total km done; for PURION/NYON the partial

•

and total km will be visible asusual on the display;

parameter [1.5] > Display Type (only Bosch) 1.1 Purion/Nyon (default) 2.2 Intuvia; 3.3 Nyon

•

parameter [2.5] > Choice of wheel circumference size:•

wheel circumference (default value > 21.7 equivalent to 2170 mm or 27.5” standard•

wheel) the value must be as close as possible to the real circumference in order to have a

correct reading of the speed. The use of automatic calibration is recommended (parameter

4.5);

parameter [3.5] > Choice of activation/deactivation unlock button: you can change the

•

default setting (default value> 4.4 WALK key) by choosing: 1.1 RESET key, 2.2 LIGHT key, 3.3

sequence+++ or 4.4 WALK.1.1 RESET button , 2.2 LUCI (LIGHTS) button , 3.3 sequence +++

or 4.4. WALK.

CHANG ES TO THE

YOUTUBE VIDEO:

https://youtu.be/qr_QfI5uDdc

10. INSTALLATION

FACTORY SETTINGS

parameter [4.5] > Automatic calibration of wheel circumference: If the bike is stopped, the•

message 55.6 will appear on the display for a few seconds, at the end of calibration 50.1

appears. If the bike is moving or the magnet on the spokes is positioned above the sensor,

calibration is NOT STARTED and 99.9 appears on the display;

parameter [5.5] > Km Reset ODO and TRIP calculated in unlocker mode;

•

parameter [6.5] > software version•

4. Make the choice and wait for about 5-10 seconds to enter the parameter to be modied.

5. Change the value with the [+ -] keys as desired: then wait a few seconds until the value is

positioned at 0.0.

For Intuvia displays

1. Modify the default parameters by specifying you will be using an Intuvia display ( see point 3,

parameter [1]

2. At rst use you’ll have to reset Trip.

3. For technical reasons, only on Intuvia display, the total distance will start from ‘0’ and will

increase until the bike is switched o . When you turn the bike on again, the value will restart

from ‘0’. In order to visualize the total kms travelled, it will be necessary to press the INFO button

and position on the ‘TOTAL KM’, then follow Point 3, parameter [0]

4. The partial Km will continue to increase until they are not put back to zero with the RESET

button.

Attention: the visualization of the total Km travelled will be possible only after having covered

at least 100 km

For Nyon display

it is necessary to change the factory parameters specifying that the Nyon display is used. See

point 3, parameter 1.5

Warning: the Nyon display will show the correct speed and the kilometers done with the unlock

activated halved.

YOUTUBE VIDEO:

https://youtu.be/qr_QfI5uDdc

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de Bosch

Bosch

Bosch 1 270 020 906 Manual de usuario

Bosch

Bosch Active Intuvia 1 270 020 906 Manual de usuario

Bosch

Bosch Active Line Manual de usuario

Bosch

Bosch BDU280P CX Manual de usuario

Bosch

Bosch Kiox BUI330 Manual de usuario

Bosch

Bosch PowerPack 300 Manual de usuario

Bosch

Bosch Kiox 300 Manual de usuario

Bosch

Bosch Purion BUI210 Manual de usuario

Bosch

Bosch Surly BDU330 Manual de usuario

Bosch

Bosch 1 270 020 909 Manual de usuario

Bosch

Bosch Intuvia BUI255 Manual de usuario

Bosch

Bosch 0 275 007 021 Manual de usuario

Bosch

Bosch BDU3360 Manual de usuario

Bosch

Bosch PowerTube 750 Manual de usuario

Bosch

Bosch 0 275 007 042 Manual de usuario

Bosch

Bosch KB069 RW Series Diagrama de cableado

Bosch

Bosch HERCULES E-Imperial I-F8 Manual de usuario

Bosch

Bosch BBS240 Manual de usuario

Bosch

Bosch BSP3200 Manual de usuario

Bosch

Bosch BDU280P CX Manual de usuario

Bosch

Bosch Kiox 300 Manual de usuario

Bosch

Bosch Intuvia eShift Manual de usuario

Bosch

Bosch Kiox BUI330 Manual de usuario

Bosch

Bosch Nyon BUI275 Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

Cateye

Cateye RAPID X2 Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

Cateye

Cateye V2C - Manual de instrucciones

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario

Bosch eplus ACTIVE LINE Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas